The Einstein relation in nanostructured materials: simplified theory and suggestion for experimental determination

An attempt is made to study the Einstein relation for the diffusivity–mobility ratio (DMR) in quantum wells (QWs) and quantum well wires (QWWs) of tetragonal compounds on the basis of a newly formulated electron energy spectrum taking into account the combined influences of the anisotropies in effective electron mass, the spin–orbit splitting, and the presence of crystal field splitting, respectively. The results for quantum-confined III–V compounds form a special case of our generalized analysis. The DMR has also been studied for QWs and QWWs of II–VI and IV–VI materials. Taking QWs and QWWs of CdGeAs₂, InAs, CdS and PbSe as examples, it was found that the DMR increases with increasing carrier statistics and decreasing film thickness respectively in various oscillatory manners emphasizing the influence of dimensional quantizations and the energy band constants in different cases. An experimental method of determining the DMR in nanostructures with arbitrary dispersion laws has also been suggested and the present simplified analysis is in agreement with the suggested relationship. The well-known results for nanostructures with parabolic energy bands have also been obtained as special cases from this generalized analysis under certain limiting conditions.     

The electrochemical behaviour of nitrogen-containing austenitic stainless steel in methanolic solution

The corrosion behaviour of nitrogen-containing austenitic stainless steel in methanol containing different concentrations of H₂SO₄, HCl, LiCl and H₂SO₄ + HCl has been investigated using a potentiostatic polarization method. The cathodic reaction in the H₂SO₄, HCl and H₂SO₄ + HCl solutions was proton reduction whereas in the neutral LiCl solution, oxygen reduction was the predominant cathodic reaction. Active, passive and transpassive behaviours were observed only for higher concentrations of H₂SO₄ (0.01–2.0 M) due to the inherent water content. A cathodic loop, characterized by measured negative current in the anodic region, was also observed in solutions, in which the concentration of H₂SO₄ was 1.0 M or higher. The relative stability of the passive films decreased as the H₂SO₄ concentration increased, and thus the steel suffered from mild pitting corrosion. In the chloride environment, the rate of corrosion increased as the Cl⁻ ion concentration increased. The presence of acid along with Cl⁻ ions enhanced corrosion, and the corrosion rate increased significantly. The steel suffered from mild intergranular corrosion in acidic chloride solutions of methanol. In the H₂SO₄ + HCl solutions, passive films were only formed when the H₂SO₄ to HCl concentration ratio was greater than ∼10:1.     

Copper(II) removal from aqueous solutions by fly ash

The removal of Cu(II) by adsorption on fly ash has been found to be concentration, pH and temperature dependent. The kinetics of adsorption indicates the process to be diffusion controlled. The Langmuir constants have been calculated at different temperatures, and the adsorption has been found to be endothermic (ΔH = 15.652 kcal mol^?1). The maximum removal is observed at pH 8.0, and variation in adsorption with pH has been explained on the basis of surface ionisation and complexation.     

On certain classes of exact solutions of Einstein equations for rotating fields in conventional and nonconventional form

Using the symmetry reduction approach we have herein examined, under continuous groups of transformations, the invariance of Einstein exterior equations for stationary axisymmetric and rotating case, in conventional and nonconventional forms, that is a coupled system of nonlinear partial differential equations of second order. More specifically, the said technique yields the invariant transformation that reduces the given system of partial differential equations to a system of nonlinear ordinary differential equations (nlodes) which, in the case of conventional form, is reduced to a single nlode of second order. The first integral of the resulting nlode has been obtained via invariant-variational principle and Noether’s theorem and involves an integration constant. Depending upon the choice of the arbitrary constant two different forms of the exact solutions are indicated. The generalized forms of Weyl and Schwarzschild solutions for the case of no spin have also been deduced as particular cases. Investigation of nonconventional form of Einstein exterior equations has not only led to the recovery of solutions obtained through conventional form but it also yields physically important asymptotically flat solutions. In a particular case, a single third order nlode has been derived which evidently opens up the possibility of finding many further interesting solutions of the exterior field equations.     

An analysis of the electrical conductivity in BaSO4-added Ag2SO4 solid electrolyte system

The compositions (1 −x)Ag₂SO₄−(x)BaSO₄, wherex=0·01 to 0·6, were prepared by slow cooling of the melt. The extent of the solid solubility of Ba²⁺ in Ag₂SO₄ was determined by X-ray powder diffraction and scanning electron microscopy. The bulk conductivity of each sample was obtained using a detailed impedance analysis. The partial substitution of Ba²⁺ results in the enhancement of conductivity in compliance with the classical aliovalent doping theory. A simplistic model based on lattice distortion (expansion) due to partial substitution of Ag⁺ by the bigger Ba²⁺ has been considered to explain enhanced conductivity. Beyond solid-solubility limit (5·27 mole%) the BaSO₄-dispersed Ag₂SO₄ conductivity follows the usual trend seen in binary systems. An increase in conductivity in this case is discussed in the light of interfacial reactions and surface defect chemistry. The maximum conductivity in 20 mole% BaSO₄ dispersed Ag₂SO₄ is due to percolation threshold.     

Methods used in dentin bonding tests: an analysis of 50 investigations on bond strength

Researchers have carried out a variety of investigations to determine the properties of available dentin bonding systems. The test methods and variables used in 50 published investigations of bond strength were analyzed. Among the studies analyzed, shear tests predominated, being used in 80% of the studies; dentin from human molar teeth was used most often (in 88% of investigations); and the most prevalent time of testing was 24 hours postcuring. However, a number of potential variables were not recorded in a high proportion of articles, among these the film thickness, the type of dentin tested, and the surface condition (moist or dry). The mode of failure was recorded in only 42% of the investigations assessed. It was found that there is little standardization of test methods in studies of dentin bond strength and that a number of variables are often either not recorded or reported.     

Micromanipulation and cloning studies on buffalo oocytes and embryos using nucleus transfer

1. Nine male volunteers were exposed to the pyrethroid insecticide cyfluthrin. The study was performed in an exposure room, where an aerosol containing cyfluthrin was sprayed to obtain atmospheres with mean cyfluthrin concentrations of 160 and 40 micrograms/m3. Four volunteers were exposed for 10, 30 and 60 min at 160 micrograms/m3 and another five volunteers were exposed for 60 min at 40 micrograms/m3. For 160 micrograms/m3 exposure urine samples were collected before and immediately after exposure as well as for the periods 1-2, 2-3, 3-4, 4-5, 5-6, 6-12 and 12-24 h after exposure. For 40 micrograms/m3 exposure urine samples were collected before and 2 h after exposure. 2. The main urinary cyfluthrin metabolites, cis-/trans-3-(2,2-dichlorovinyl)-2,2-dimethylycyclopropane carboxylic acid (DCCA) and 4-fluoro-3-phenoxybenzoic acid (FPBA), were determined. The limit of detection (LOD) for all metabolites was 0.0025 microgram in an urine sample of 5 ml (0.5 microgram/l). After inhalative exposure of 40 micrograms cyfluthrin/m3 air for 60 min, the amount of metabolites in urine collected in the first 2 h after exposure was less than the LOD, namely 0.14 microgram for cis-DCCA, 0.15-0.28 microgram for trans-DCCA and 0.12-0.23 microgram for FPBA. 3. Of the metabolites, 93% was excreted within the first 24 h (peak excretion rates between 0.5 and 3 h) after inhalative exposure of 160 micrograms/m3. The mean half-lives were 6.9 h for cis-DCCA, 6.2 h for trans-DCCA and 5.3 h for FPBA. 4. The mean trans-:cis-DCCA ratio was 1.9 for the time course as well as for each subject. 5. The amount of metabolites in urine depends on the applied dose, on the exposure time and shows interindividual differences.     

Response spectrum analysis of piping systems with elastic-plastic gap supports

A new seismic support device and its application in piping systems is described. The device, E-BAR (patented), can be cost effectively used for snubber replacement programs, mitigation of hydraulic transients, pipe whip and as a thermal stop. The device has pre-set gaps to allow free thermal movement. During a seismic or other dynamic load event, if the pipe movement exceeds the gap dimension, the device acts as an elastic or elastic-plastic restraint. The device also has a unique design feature for not exceeding the restraint force beyond a specified limit design value. To analyze piping systems with gap supports having elastic-plastic characteristics, modal analysis procedures for both response spectrum and time history methods are developed. The comparison of responses obtained from the procedures with nonlinear time history analysis and test results available in the literature shows excellent correlation. A pilot program conducted for snubber replacement with E-BARs demonstrates that the limit force feature of E-BAR makes them very attractive for snubber replacement. This is because a particular E-BAR with a specified limit design force can be selected, such that, the E-BAR replacing the snubber does not require any modifications be made to the existing support steel and hardware.     

Induction of superoxide dismutase isozymes by tumor necrosis factor-alpha and lipopolysaccharide in cultured normal and hyperplastic gingival fibroblasts

We studied 722 reexcision scars of benign and malignant lesions (except melanocytic lesions) excised over a 24-month period. The formalin-fixed, paraffin-embedded tissue sections were examined histologically and immunohistochemically. The histological features of melanocytic hyperplasia were present in 59 cases (8%), 56 from the sun-exposed skin of the face and neck and three from the trunk [p < 0.00001]. The most common sites were the nose and lower eyelids, but the forehead was also frequently involved. Of the 59 patients, 41 were women (p < 0.0001). Basal cell carcinoma was the most frequent original lesion in both sexes (80%). No melanocytic hyperplasia was found in 663 cases (298 on the trunk and extremities and 365 on the head and neck). We have seen this reaction pattern following reexcision of melanocytic lesions as well. Thus, interpreting reexcision margins when lentigo maligna or similar lesions are reexcised may be fraught with difficulty. It is important for pathologists and dermatopathologists to recognize this phenomenon because histologically the presence of increased numbers of large melanocytes could be misinterpreted as melanoma in situ.     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities