Investigation of the changes in physical properties of PES/PVC fabrics after aging

The aim of this work was to investigate the physical and mechanical performance of architectural polyester (PES)–poly(vinyl chloride) (PVC) membranes exposed to different artificial aging conditions. Two commercially available architectural membranes were chosen as research objects. The durability of the PES/PVC fabrics was evaluated by the loss in mechanical performance, scanning electron microscopy, and X-ray diffraction analysis in order to understand the effect of the degradation agents on the surface of the membranes. The mechanical performance of the PES/PVC membranes was unchanged. Scanning electron microscopy images of the tested materials showed initial cracks after aging. The X-ray fluorescence analysis showed that at the time of aging, the amount of Cl and Si decreased slightly, while Ti decreased by half, and Ca by volume increased twice. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47523.     

Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Mechanochemical synthesis of YNbO4:Eu nanocrystalline powder and its structural,microstructural and photoluminescence properties

In this research we prepared nanocrystalline YNbO₄:Eu³⁺ phosphor, i.e. nanophosphor, powder using an efficient mechanochemical method followed by annealing. X-ray diffraction analysis revealed that YNbO₄:Eu³⁺ crystallizes in monoclinic structure C2/c where, from the point of view of A and B in ABO₄ compounds, cation coordination can be noted as [6+2, 4+2]. Crystallite size of about 40 nm, was estimated using Debye Scherrer's equation. Raman spectroscopy with 785 and 532 nm excitation wavelengths is performed to record a majority of materials phonon modes and to provide more in depth understanding of the YNbO₄ structure. Scanning electron microscopy observations indicate that the mechanical treatment during synthesis is causing non-uniformity of the powder microstructure. High resolution photoluminescent measurements upon UV excitation showed intense emission coming from f–f transitions of the europium ion with the lifetime of 0.68 ms, suggesting that the obtained YNbO₄:Eu³⁺ is a good potential phosphor. A comparison of emissive properties with microcrystalline YNbO₄:Eu³⁺ was made and it showed higher values of emission intensity and lifetime of the nanocrystalline sample.     

Fluoride in teas of different types and forms and the exposure of humans to fluoride with tea and diet

Human exposure to the fluoride (F) from commercial teas was assessed. The efficacy of the F leaching was determined from the total F (F_t) contents in the teas (53–435 mg/kg) and the F concentrations in tea infusions (0.31–3.55 mg/l of free F available to human organism). Both were determined with a fluoride ion selective electrode. The efficacies of F leaching from the green, oolong and black teas were 55–90% with continuous, and 74–100% by repeated infusions, and were not affected by the type or the manufactured form. Lower efficacies were observed from Pu’erh teas, 21–38% with continuous, and 37–59% by repeated infusions. The daily intake of F with daily consumption of five cups of tea can represent 9–101% of the adequate intake (AI) for an adult person with 70 kg, and with tea and diet 25–173% of the AI in non-fluoridated and 35–210% of AI in fluoridated areas. The upper limits of these intakes can be already associated with a risk of developing F-related adverse effects.     

On the role of 2,3-dihydro-3,5-dihydroxy-6-methyl-(4<Emphasis Type="Italic">H</Emphasis>)-pyran-4-one in antioxidant capacity of prunes

Despite available reports on phenolic composition and antioxidant capacity (AOC) of fresh plums and prunes, there is a scarcity of published knowledge on the antioxidants formed and/or released during the drying process in the literature. To evaluate the compounds participating in reducing capacity of prunes, we compared aqueous and methanol extracts of fresh plums, commercial prunes and home-made prunes prepared at different drying temperatures using an HPLC method with amperometric detection (HPLC-ECD). The prunes dried at high temperature (90 °C, 18 h) in kitchen or laboratory oven with restricted ventilation gave up to 3.3 times higher electrochemical capacity (EC) than fresh plums (dry matter; P. domestica cv. Domestica) in dependence on production protocol. Drying at 60 °C (low-temperature drying) for 18 h did not change the EC significantly. Yet, lower EC was found in commercial tenderized prunes with sorbate; they were by a factor of 1.1–8.2 lower in EC than the prepared low-temperature prunes. The principle responsible for the increase in EC in the prunes prepared at high temperatures is 2,3-dihydro-3,5-dihydroxy-6-methyl-(4H)-pyran-4-one (DDMP). It was not detected until 74 °C was set during isothermal 18 h drying or until 6 h of drying passed at 90oC drying. The ultimate acceptable dwell-time for the preparation of conveniently eatable prunes dried at 90oC under the conditions used was assessed to 12 h. The EC of plums and prunes as well as the role of DDMP was confirmed by the use of several methods for the assessment of AOC-DPPH^• assay, β-carotene bleaching method, Oxipres test and Schaal oven test.     

Fatigue crack initiation and damage characterization in Brazilian test specimens for adhesive joints

The present study is focused on the fatigue failure initiation at bimaterial corners by means of a configuration based on the Brazilian disc specimens. These specimens were previously used for the generalized fracture toughness determination and prediction of failure in adhesive joints, carried out under static compressive loading. Under static loading, local yielding effects might affect the asymptotic two-dimensional linear elastic stress representation under consideration. Fatigue loading avoids this fact due to the lower load levels used. The present tests were performed using load control; video microscopy and still cameras were used for monitoring initiation and crack growth. The fatigue tests were halted periodically and images of the corner were taken where fatigue damage was anticipated. Damage initiation and subsequent crack growth were observed in some specimens, especially in those which presented brittle failure under static and fatigue tests. These analyses allowed the characterization of damage initiation for a typical bimaterial corner that can be found in composite to aluminium adhesive lap joints.     

New filtrate loss controller based on poly(methyl methacrylate‐co‐vinyl acetate)

The drilling of petroleum wells requires the use of suitable drilling fluids to ensure efficient operation without causing rock damage. Specific polymers have been used to control infiltration during drilling, to reduce operational problems. In this study, spherical microparticles of poly(methyl methacrylate‐co‐vinyl acetate) were synthesized (by suspension polymerization), characterized, and evaluated in terms of their performance in controlling filtrate loss of aqueous fluids. A filter press test with ceramic disk, simulating the rock, was used. The performance of the synthesized materials was compared with commercial polymers. It was observed that the performance of the material is directly associated with the relation between particle size and pore size of the rock specimen. Furthermore, for a suitable particle size, the rubbery characteristic of the material produces a more efficient filter cake, for filtrate control. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40646.     

Effect of Homogenization Pressure and Oil Load on the Emulsion Properties and the Oil Retention of Microencapsulated Basil Essential Oil (Ocimum basilicum L.)

The objective of this work was to evaluate the influence of oil concentration and homogenization pressure on the emulsion and particle properties during the microencapsulation of basil essential oil by spray drying, using gum arabic as the wall material. Experiments were planned according a 2² rotational central composite design. The independent variables were oil concentration with respect to total solids (10–25%) and homogenization pressure (0–100 MPa). Emulsions were analyzed for droplet mean diameter, stability, and viscosity, and particles were analyzed for oil retention, moisture content, particle size, and morphology. Emulsion viscosity was not affected by any of the independent variables. The increase in the homogenization pressure from 0 to 100 MPa resulted in smaller emulsion droplet size (down to 0.40 µm) and, consequently, higher oil retention (up to 95%). On the other hand, higher oil loads (25%) resulted in poorer oil retention (51.22%). Microencapsulation of basil essential oil using gum arabic as the wall material proved to be a suitable process to obtain powdered basil essential oil, presenting great oil retention with the use of lower oil concentration and higher homogenization pressure.