Dynamic modeling of a dual active bridge DC to DC converter with average current control and load‐current feed‐forward

Bidirectional power flow is needed in many power conversion systems like energy storage systems, regeneration systems, power converters for improvement of the power quality and some DC‐DC applications where bidirectional high power conversion and galvanic isolation are required. The dual active bridge (DAB) is an isolated, high voltage ratio DC‐DC converter suitable for high power density and high power applications, being a key interface between renewable energy sources and energy storage devices. This paper is focused on the modeling and control design of a DC‐DC system with battery storage based on a DAB converter with average current mode control of the output current and output voltage control. The dynamic response of the output voltage to load steps is improved by means of an additional load‐current feed‐forward control loop. An analytical study of the load‐current feed‐forward is presented and validated by means of both simulations and experimental results. Copyright © 2014 John Wiley & Sons, Ltd.     

Influence of deposited metal structures on the failure mechanisms of silicon-based components

Miniaturised silicon-based multilayer chips are nowadays widespread as semiconductor components for the mobile device technology. The use of special processing and integration procedures requires such materials to possess a definite mechanical strength to ensure the functionality of the entire device. The strength and mechanical reliability of such components can be described by the Weibull theory, and is highly influenced by the geometry of the metallisation and other near-surface functional layers. In this work, we attempt to clarify the mechanisms leading to the failure of the metallised side of Si-chip components. The combined use of Finite Elements (FE) and Focused Ion Beam (FIB) analyses allowed recognising that cracks are induced in the metal-oxide-silicon interfacial area well before complete failure of the component. Such cracks have a crucial role in the lower strength and higher Weibull modulus observed on the metallised side.     

An efficient microwave-assisted Suzuki reaction using Pd/MCM-41 and Pd/SBA-15 as catalysts in solvent-free condition

Palladium catalysts, Pd/MCM-41 and Pd/SBA-15 were prepared by impregnation of an aqueous solution of [Pd(NH₃)₄]Cl₂ on MCM-41 and SBA-15. Palladium contents of Pd/MCM-41 and Pd/SBA-15 are 8.4% and 8.7%, respectively. It has been shown that these catalysts are very suitable to microwave-assisted Suzuki reactions under solvent-free condition. It is also found that the base additives for this reaction are K₂CO₃, Cs₂CO₃ or CsF. Thus, phenylboronic acid and phenyl iodide with Pd/MCM-41 produce biphenyl by microwave irradiation for 10 min in 97.4% yield. Phenyl bromide, instead of phenyl iodide, also proceeds the reaction with phenylboronic acid using Pd/MCM-41 or Pd/SBA-15 yielding biphenyl by microwave irradiation for 10 min in excellent yield. Whereas the reaction of phenyl chloride with phenylboronic acid gives poor yield in same condition. Various aryl iodides and aryl bromides are tested. In this paper our recent results of microwave-assisted Suzuki reaction using Pd/MCM-41 and Pd/SBA-15 under solvent-free condition are described.     

Validation of SeaWiFS-derived chlorophyll for the Rio de la Plata Estuary and adjacent waters

The South Atlantic Ocean near the Río de la Plata Estuary is a highly dynamic region that encompasses four different water bodies: the Río de la Plata, the continental shelf and the Brazil and Malvinas currents. Bio-optical measurements obtained during 6–11 November 1999 provided the initial field data for validating Sea viewing Wide Field of view Sensor (SeaWiFS)-derived chlorophyll imagery for this region. The turbid waters of the Río de la Plata Estuary showed the highest variability and complexity in water optical properties, while the offshore waters of the Brazil Current had the lowest. In most cases, the estimates of chlorophyll using the SeaWiFS algorithm were higher than in situ measured values.     

Influence of pH on colour and iron content of peptide fractions obtained from bovine Hb concentrate hydrolysates

The effect of pH on colour and iron content (Fe) of peptide fractions obtained from bovine haemoglobin concentrate (BHC) hydrolysates was studied. Four hydrolysates were obtained using three enzymes: Protex‐6‐L (P), Fungal–Protease–Concetrate (FC) and Flavourzyme (F). BHC and its hydrolysates (P, FC, P + F, FC + F) were fractioned at pH 4.5, 7.0 and 9.5. Solubility and Fe from different fractions were measured. Correlations between CIELAB colour parameters and Fe from different fractions were analysed. The colour from different fractions varied from red to yellow (a* and b* positives). Lightness values (L*) ranged from twenty‐four to seventy. FC4.5 and FC + F4.5 fractions were the clearest and yellow (higher L*, b*, h), while BHC9.5 and P + F9.5 fractions had the lowest values of L*, b* and h. There was an inverse linear relationship between b* and L* parameters and Fe from fractions. This relationship could be associated with the pH of extraction. As pH increases Fe significantly increases and lower b* and L* values were obtained.     

Non‐minimum phase switched systems: HOSM‐based fault detection and fault identification via Volterra integral equation

In this paper, the problem of continuous and discrete state estimation for a class of linear switched systems with additive faults is studied. The class of systems under study can contain non‐minimum phase zeroes in some of their ‘operating modes’. The conditions for exact reconstruction of the discrete state are given using structural properties of the switched system. The state space is decomposed into the strongly observable part, the non‐strongly observable part, and the unobservable part, to analyze the effect of the unknown inputs. State observers based on high‐order sliding mode to exactly estimate the strongly observable part and Luenberger‐like observers to estimate the remaining parts are proposed. For the case when the exact estimation of the state cannot be achieved, the ultimate bounds on the estimation errors are provided. The proposed strategy includes a high‐order sliding‐mode‐based fault detection and a fault identification scheme via the solution of a Volterra integral equation. The feasibility of the proposed method is illustrated by simulations. Copyright © 2013 John Wiley & Sons, Ltd.     

Salt in food processing; usage and reduction: a review

Salt is one of the most widely used additives in food industries because of its low cost and varied properties. It has a preservative and antimicrobial effect as a direct consequence of the capacity of sodium chloride to reduce water activity values. In addition, sodium chloride is a flavour enhancer as a consequence of its effect on different biochemical mechanisms. It also has flavour enhancing effects from reducing or enhancing the enzymatic activity of some enzymes responsible for the development of different organoleptic parameters. Trends in sodium chloride use in food industries point to salt replacement or reduction by means of the use of sodium chloride substitutes such as KCl or phosphates; flavour enhancers and the optimisation of the physical form of salt. This trend has arisen as a result of the greater awareness of the negative effects of excess dietary intake of sodium, which has been linked to hypertension and consequently an increased risk of cardiovascular disease. The average total daily sodium intake per individual in developed countries is 4–5 g of Na, which is up to 25 times greater than the minimum adult requirement.     

Highly Stretchable and Sensitive Strain Sensors Using Fragmentized Graphene Foam

Stretchable electronics have recently been extensively investigated for the development of highly advanced human‐interactive devices. Here, a highly stretchable and sensitive strain sensor is fabricated based on the composite of fragmentized graphene foam (FGF) and polydimethylsiloxane (PDMS). A graphene foam (GF) is disintegrated into 200–300 μm sized fragments while maintaining its 3D structure by using a vortex mixer, forming a percolation network of the FGFs. The strain sensor shows high sensitivity with a gauge factor of 15 to 29, which is much higher compared to the GF/PDMS strain sensor with a gauge factor of 2.2. It is attributed to the great change in the contact resistance between FGFs over the large contact area, when stretched. In addition to the high sensitivity, the FGF/PDMS strain sensor exhibits high stretchability over 70% and high durability over 10 000 stretching‐releasing cycles. When the sensor is attached to the human body, it functions as a health‐monitoring device by detecting various human motions such as the bending of elbows and fingers in addition to the pulse of radial artery. Finally, by using the FGF, PDMS, and μ‐LEDs, a stretchable touch sensor array is fabricated, thus demonstrating its potential application as an artificial skin.