An experimental study of the thermodynamic properties of 1,1-difluoroethane

Experimental vapor pressures andP--T data of an important alternative refrigerant, 1, 1-difluoroethane (HFC-152a), have been measured by means of a constant-volume method coupled with expansion procedures. SixtyP--T data were measured along eight isochores in a range of temperaturesT from 330 to 440 K, at pressuresP from 1.6 to 9.3 MPa, and at densities from 51 to 811 kg·m^–3. Forty-six vapor pressures were also measured at temperatures from 320 K to the critical temperature. The uncertainties of the temperature and pressure measurements are within ±7mK and ±2kPa, respectively, while the uncertainty of the density values is within ±0.1%. The purity of the sample used is 99.9 wt%. On the basis of the measurements along each isochore, five saturation points were determined and the critical pressure was determined by correlating the vapor-pressure measurements. The second and third virial coefficients for temperatures from 360 to 440 K have also been determined.     

Preparation of spherical fine ZnO particles by the spray pyrolysis method using ultrasonic atomization techniques

An ultrasonic atomizer was used in the spray pyrolysis method to prepare fine, spherical and uniform ZnO particles. Almost spherical particles were obtained successfully which had a mean particle size of 0.15 m and had a very narrow particle size distribution. By using alcohol as the solvent, it was found that the particles do not have hollow shell layers which could usually be observed in the spray pyrolysis process by using water as the solvent. The morphology of the ZnO particles was strongly affected by the concentration of the starting solution.     

Co-crosslinking blend of incompatible polymers VI: Poly(vinyl chloride) toughened with polyethylene via a co-crosslinking technique

A binary blend which consists of two incompatible polymers such as poly(vinyl chloride) and polyethylene has been performed through a partial co-crosslinking reaction with peroxide to give a co-crosslinked blend with a uniform dispersion of small polyethylene particles and with an improved mechanical property. The results are obtained through the formation of a co-crosslinked product which acts as a potential solid phase dispersant as well as a well-bonded reinforcing interlayer on polyethylene particles uniformly dispersed in poly(vinyl chloride) matrix. The resulting blends (PVC/PE=10/90 wt) give carbon spherules of 0.5 to 1m diameter through pressure-carbonization at 650° C for 1 h.     

Autonomous Visual Measurement for Accurate Setting of Workpieces in Robotic Cells

This paper introduces a new method of adapting the virtual world of an offline programming model to an actual robotic cell by attaching a CCD camera to the robot. This method requires no specific camera attachment location or optical camera calibration. Furthermore, there is no operational requirement for setting robotic camera location. Robot motion is autonomously generated to identify the camera view line. The view line is adjusted to pass through the designated target point, utilizing visual feedback motion control. This method calibrates reference points between the virtual world of an offline model to an actual robotic cell.     

Use of LINbO3 for Design of Device-type Catalysts with Activity Controllable Functions

A poled ferroelectric LiNbO₃ single crystal with high spontaneous polarization was employed as a catalyst support, and the static and dynamic effects of the polar substrate surfaces on the adsorptive and catalytic properties of thin film catalysts deposited were shown. For the static effect, it was demonstrated that the surface conductivity of copper and metal-free phthalocyanine films increased by the adsorption of NO gas, to a larger extent, when the substrate was the negative polar surface, compared to the positive one. The role of the polar substrates is explained In terms of a band bending model. For the dynamic effect, the Rayleigh surface acoustic wave generated on the LiNbO₃ substrate was shown to enhance the catalytic activity for ethanol oxidation on Cu and Ag thin film catalysts deposited on the propagation path. It is proposed that the catalyst activation is mainly due to an electric Held produced. The use of poled LiNbO₃ is suggested to be effective for the development of a device-type catalyst with activity controllable functions.     

Mechanical Properties of Alumina/Silicon Carbide Whisker Composites

The improvement of mechanical properties of Al₂O₃/SiC whisker composites has been studied with emphasis on the effects of the whisker content and of the hot-pressing temperature. Mechanical properties such as fracture toughness and fracture strength increased with increasing whisker content up to 40 wt%. In the case of the high SiC whisker content of 40 wt%, fracture toughness of the sample hot-pressed at 1900° decreased significantly, in spite of densification, compared with one hot-pressed at 1850°. Fracture toughness strongly depended on the microstructure, especially the distribution of SiC whiskers rather than the grain size of the Al₂O₃ matrix.     

Ring hydrogenation of naphthalene and 1-naphthol over supported metal catalysts in supercritical carbon dioxide solvent

Catalytic ring hydrogenations of naphthalene and 1-naphthol were studied over several supported metal catalysts in supercritical carbon dioxide solvent at low temperature. Higher concentration of hydrogen in supercritical carbon dioxide and lower reaction temperature were responsible for higher catalyst activity and selectivities to the desired partial ring hydrogenated products as compared with those observed in organic solvent for the same catalyst.     

Studies on the nuclear magnetic resonance spectra of olefinic protons of conjugated fatty acid methyl esters

The NMR spectra of olefinic protons in the four representative conjugated fatty acid methyl esters, methylcis-9,trans-11-octadecadienoate, methyltrans-9,trans-11-octadecadienoate, methyl α eleostearate, and methyl β eleostearate, were studied. The chemical shift of each olefinic proton in these compounds was determined by considering their intramolecular environment. Coupling constants were also obtained as the results of spectral analysis.     

Role of Acetic Acid Added to the Reaction Media for the Enantio-differentiating Hydrogenation of Methyl Acetoacetate Over a Tartaric Acid-modified Nickel Catalyst

The role of acetic acid added to the reaction media for the enantio-differentiating hydrogenation of methyl acetoacetate over a (R,R)-tartaric acid-in-situ-modified nickel catalyst was studied from the viewpoint of the hydrogenation rate during repeated runs. The hydrogenation of methyl acetoacetate on the “enantio-differentiating sites” of a tartaric acid-modified nickel catalyst was specifically accelerated by the acetic acid added to the reaction media to increase the enantio-differentiating ability of the catalyst. In order to increase the enantio-differentiating ability, the addition of acetic acid to the reaction media was required in each run during the repeated use of the catalyst.     

Large macro-dipoles generated in a supramolecular polymer of N,N′,N″-tris(3,7-dimethyloctyl)benzene-1,3,5-tricarboxamide in n-decane

A supramolecular polymer formed by N,N′,N″-tris(3,7-dimethyloctyl)benzene-1,3,5-tricarboxamide (DO₃B) in n-decane (C₁₀) possesses large macro-dipoles naturally generated by three-fold inter-molecular hydrogen bonding aligned along its helical columnar structure connected by defective portions, which are DO₃B molecules containing failure in the hydrogen bond formation, in the order of head to tail arrangement without dipole inversion like type-A polymers.