Zur kinetik der acrylnitril-polymerisation

The heterogeneous bulk polymerization of acrylonitrile initiated by AIBN has been studied by means of an improved dilatometric technique and a new method of analysis, where the initial reaction rate (v_w)₀ results from the intercept of a straight line in a \documentclass{article}\pagestyle{empty}\begin{document}$ \frac {\ln \left( 1 \hbox{---} {\rm U} \right)} {{\rm e}^{{- 0,5} {\rm k}_{\rm s}{\rm t} \hbox{---} 1}}$\end{document} versus t plot. It has been found that the initial reaction rate is proportional to the square root of the initial catalyst concentration S₀. The ratio of the rate coefficients of propagation and termination\documentclass{article}\pagestyle{empty}\begin{document}$\frac { {\rm k}_{\rm a} } { {\rm k}_{ {\rm w}^{2} } } $\end{document} could be calculated from the slope of a straight line passing through the origin in a plot of (v_w)₀ versus \documentclass{article}\pagestyle{empty}\begin{document}$\sqrt { {\rm S}_{0} }$\end{document} and yielded a value of 280 mol 1^?1.     

Dehydrogenation of Light Alkanes Over Rhenium Catalysts on Conventional and Mesoporous MFI Supports

Recently, Re/HZSM-5 (Si/Al = 15) was shown to be an efficient catalyst for ethane dehydrogenation and aromatization at 823 K and atmospheric pressure. In this reaction, the major initial products were benzene, toluene and xylene (BTX), but increasing amounts of ethene were produced with time on stream due to deactivation of the catalyst. We show that by use of rhenium impregnated MFI supports with very few or no acidic sites (Si/Al > 500), highly selective ethane dehydrogenation catalysts are obtained with ethene selectivities of 98%. By use of mesoporous MFI supports (Si/Al >500) the lifetime of the catalyst appears to be slightly improved compared to conventional MFI crystals. The beneficial effect of a mesoporous MFI support is convincingly demonstrated in propane dehydrogenation, where both conversion and selectivities on the mesoporous MFI (Si/Al > 500) impregnated with Re are significantly higher than on Re supported on a comparable conventional MFI support.     

Mandibular gland secretions of the male beewolvesPhilanthus crabroniformis,P. barbatus,andP. pulcher (Hymenoptera: Sphecidae)

The composition of the territorial marking pheromones from mandibular glands of males of the beewolvesPhilanthus crabroniformis, P. barbatus, andP. pulcher have been determined. The structures of the components were elucidated by gas chromatography-mass spectrometry and gas chromatography-Fourier transform infrared spectroscopy. The major compound ofP. crabroniformis is isopropyl tetradecanoate, with somewhat lesser amounts of 2-tridecanone, 3-methyl-3-butenyl tetradecanoate, and 928 (Z)(E)-11-eicosen-1-ol. The major compounds ofP. barbatus are ethyl tetradecanoate and hexadecanal, which are present in approximately a 6040 ratio. These two compounds comprise over 95% of the neutral lipids. Also present in lesser amounts are ethyl dodecanoate, tetradecanal, hexadecan-1-ol, a ^x -octadecen-1-ol, and octadecan-1-ol. The major compounds ofP. pulcher are ethyl (Z)-7-hexadecenoate and geranylgeraniol acetate, which comprise nearly 90% of the neutral lipid fraction, with smaller amounts of tetradecanal, pentadecanal, and ethyl hexadecanoate; trace amounts of ^x hexadecenal, hexadecanal, and octadecanal are also present.     

Organic Nanoparticles with Polypropyleneoxide Chains as Support for Metallocene Catalysts: Ethylene Homopolymerization and Ethylene/α-olefin Copolymerization

Summary Novel organic nanoparticles functionalized with nucleophilic polypropyleneoxide (PPO) chains on their surfaces for supporting metallocene catalysts in heterogeneous olefin polymerization are presented. The nanoparticles (60–100 nm) were obtained by miniemulsion polymerization of styrene, divinylbenzene and PPO functionalized styrene. It is demonstrated that Me₂Si(2MeBenzlnd)₂ZrCl₂/MAO supported on these nanoparticles is suitable for the homopolymerization of ethylene, resulting in excellent product morphologies and high activities. lt is shown that by varying the MAO/Zr ratios and Zr concentrations the activities and productivities of the catalysts as well as the qualities of the polyethylene products can be tuned. These new supported catalysts are also suitable for the copolymerization of ethylene with several comonomers (1-hexene, 1-octene, 1-decene or norbornene). As the obtained product properties like crystallinity, melting temperature or bulk density match the results of silica supported systems, these organic nanoparticles can be considered as alternative carriers in comparison to the established inorganic ones.     

Compatibilization of polymer blends from poly(styrene‐co‐acrylonitrile) and polycarbonate by oxazoline modification of poly(styrene‐co‐acrylonitrile) in the melt

A good way of achieving compatibility in polymer blends of poly(styrene‐co‐acrylonitrile) (S/AN) and bisphenol A polycarbonate (PC) is the chemical modification of S/AN in the melt. A catalyzed reaction of the nitrile groups with a substituted 2‐amino alcohol or 2‐amino phenol resulted in a conversion of nitrile groups of 55–75% in 60 min. The introduced heterocyclic structures were ethyl hydroxymethyl oxazoline (EHMOXA) and benzoxazole (BenzOXA), respectively. The use of dibutyltin oxide as a catalyst led to the highest efficiency. The modified polymer was characterized by Fourier transform infrared and NMR spectroscopy, elemental analysis, and reactions with organic acids and anhydrides. The modified S/AN showed good technical compatibility (single glass‐transition temperature) with PC in blends made from solution and from the melt. All blends were characterized with oscillating rheometry and differential scanning calorimetry. Rheological measurements showed that EHMOXA–S/AN reacted with PC and had crosslinked structures, whereas BenzOXA–S/AN showed compatibilization without any (crosslinking) reaction. The melt blends of BenzOXA–S/AN and PC showed a downward shift in the complex viscosity due to the influence of the BenzOXA group. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2322–2332, 2003     

Closed‐Loop Identification for Control of Linear Parameter Varying Systems

This paper deals with system identification for control of linear parameter varying systems. In practical applications, it is often important to be able to identify small plant changes in an incremental manner without shutting down the system and/or disconnecting the controller; unfortunately, closed‐loop system identification is more difficult than open‐loop identification. In this paper we prove that the so‐called Hansen scheme, a technique known from linear time‐invariant systems theory for transforming closed‐loop system identification problems into open‐loop‐like problems, can be extended to accommodate linear parameter varying systems as well. We investigate the identified subsystem's parameter dependency and observe that, under mild assumptions, the identified subsystem is affine in the parameter vector. Various identification methods are compared in direct and Hansen Scheme setups in simulation studies, and the application of the Hansen Scheme is seen to improve the identification performance.     

Phase stability and magnetic properties of SrFe18O27 W-type hexagonal ferrite

W-type ferrite is a member of the hexagonal ferrite family and a potential permanent magnet material. However, its synthesis conditions are not fully understood yet. Samples were sintered either at 1400°C in air and quenched, or at 1300°C at reduced oxygen partial pressure. The precise stability conditions of this W-type ferrite were investigated in the temperature range of 1200°C-1400°C using thermogravimetry, XRD, and electron microscopy. At 1300°C, the ferrite is stable at oxygen partial pressures of . At more oxidizing conditions, the ferrite decomposes into M-type ferrite and hematite, while at more reducing atmospheres Sr₄Fe₆O₁₃ and magnetite are formed. The nonstoichiometry δ of SrFe_18−δO₂₇ was derived from thermal analysis data at 1300°C as function of oxygen partial pressure and was found to be mainly due to cation vacancies. Magnetization measurements show that this W-type ferrite exhibits M_s = 103 emu/g at T = 4 K, which agrees well with a ferrimagnetic spin arrangement according to Gorter's model. As alternative, Zn-substituted W-ferrite was found to be stable in air at 1200°C with a large M_s = 123 emu/g at 4 K.     

Small-angle neutron scattering from branched epoxide resins

Small-angle neutron scattering experiments in the range of q² from 0.01 to 25 nm⁻² have been carried out on branched epoxide resins based on bisphenol-A at the Institute Laue—Langevin (I.L.L) in Grenoble (q=(4π/λ) sin(θ/2)). Measurements were made with six samples in the range of M_W from 1500 to 19 000 and four concentrations between 1.3 and 10% (w/w) in deuterated diglyme. The results are as follows: (i) The mean square radius of gyration follows a relationship S²_z=4.69×10⁻⁴M^1.20_W (nm²). (ii) In all cases fairly large second virial coefficients A₂ are obtained which, however, decrease strongly with molecular weight. Above M_W=2500, the virial coefficient follows the relationship A₂=1.6M^−0.85_W (mol cm³g⁻²). (ii) The reciprocal particle scattering factor as a function of q² exhibits only a slight upturn and otherwise shows the behaviour of a randomly branched polycondensate. The slight upturn is discussed as being caused by the finite volume of the monomeric unit. Possible reasons for the high exponent in the S²_z versus M_W dependence are briefly discussed.     

Stretching and deformation vibrations of CH2, C(CH3) and O(CH3) groups of poly(methyl methacrylate)

Infrared and Raman spectra of atactic PMMA and infrared spectra of stereoregular PMMA and of its four deuterated derivatives

, were measured. They were used to assign the bands of stretching and deformation vibrations of CH₂, CCH₃ and OCH₃ groups in the infrared and Raman spectra and to discuss the effect of stereoregularity on these bands in the infrared spectra.