Reduction of frequency noise and frequency shift by phase shifting elements in frequency modulation atomic force microscopy

We recently reported the analysis of the frequency noise in the frequency modulation atomic force microscopy (FM-AFM) both in high-Q and low-Q environments [Rev. Sci. Instrum. 80, 043708 (2009)]. We showed in the paper that the oscillator noise, the frequency fluctuation of the oscillator, becomes prominent in the modulation frequency lower than f(0)∕2Q, where f(0) and Q are the resonance frequency and Q-factor. The magnitude of the oscillator noise is determined by the slope of the phase versus frequency curve of the cantilever at f(0). However, in actual FM-AFM in liquids, the phase versus frequency curve may not be always ideal because of the existence of various phase shifting elements (PSEs). For example, the spurious resonance peaks caused by the acoustic excitation and a band-pass filter in the self-oscillation loop increase the slope of the phase versus frequency curve. Due to those PSEs, the effective Q-factor is often increased from the intrinsic Q-factor of the cantilever. In this article, the frequency noise in the FM-AFM system with the PSEs in the self-oscillation loop is analyzed to show that the oscillator noise is reduced by the increase of the effective Q-factor. It is also shown that the oscillation frequency deviates from the resonance frequency due to the increase of the effective Q-factor, thereby causing the reduction in the frequency shift signal with the same factor. Therefore the increase of the effective Q-factor does not affect the signal-to-noise ratio in the frequency shift measurement, but it does affect the quantitativeness of the measured force in the FM-AFM. Furthermore, the reduction of the frequency noise and frequency shift by the increase of the effective Q-factor were confirmed by the experiments.     

The study of the effect of external additives on the synthesis of fumed TiO2 with a high content of rutile structure by the novel natural dropping thermal treatment

The effect of external additives on the synthesis of fumed TiO₂ with a high rutile structure content was studied. The focus of this investigation was on the external additive species, agglomerates of the fumed TiO₂ before and after the thermal treatment. The transformation ratio from the anatase to rutile structure of the thermally-treated fumed TiO₂ was investigated as a function of the fumed TiO₂ agglomerate before the thermal treatment. Small agglomerated powders resulted in a decrease of transformation temperature. Two novel results were obtained in this investigation. One was a new fumed TiO₂ with a 100% rutile structure having an excellent dispersibility being successfully synthesized by the thermal treatment of AEROXIDE® TiO₂ P 25 with a small portion of AEROSIL® R 972. The other was the remarkable acceleration of the transformation from the anatase to rutile structure and grain growth/sintering of the thermally-treated fumed TiO₂ observed at a relatively low thermal treatment temperature by the oxidation reaction of calcium stearate as an external additive.     

Effect of a low-fat diet enriched with oleic acid on postprandial lipemia in patients with type 2 diabetes mellitus

The aim of the present study was to compare the effects of a low-fat diet enriched with oleic acid to those of a low-fat diet enriched with linoleic acid on fasting lipids, postprandial lipemia, and oxidative susceptibility of low-density lipoprotein (LDL) in patients with type 2 diabetes mellitus (DM). In a 3-wk randomized crossover study, eight patients with type 2 DM were given an experimental low-fat diet enriched with either oleic acid or linoleic acid. The oleic-acid-enriched diet contained 5, 15, and 5% energy from saturated, monounsaturated, and polyunsaturated fatty acids, and the linoleic-acid-enriched diet contained 5, 5, and 15% energy from saturated, monounsaturated, and polyunsaturated fatty acids, respectively. In addition to evaluating the fasting lipids and oxidative susceptibility of LDL, we evaluated postprandial lipemia using an oral fat load at the end of each 3-wk dietary phase. There were no significant differences in fasting lipid profile or lag time of LDL oxidation between the two experimental dietary phases. The average and maximal increments of remnant-like particle (RLP) cholesterol levels during oral fat load were significantly higher after the oleic-acid-enriched dietary phase than after the linoleic-acid-enriched dietary phase. The area under the curve of RLP cholesterol was also significantly larger after the oleicacid-enriched dietary phase than after the linoleic-acid-enriched dietary phase. These results suggest that the oleic-acidenriched diet was associated with increased formation of postprandial chylomicron remnants compared with the linoleicacid-enriched diet.     

A surface motor-driven planar motion stage integrated with an XYθZ surface encoder for precision positioning

This paper describes a surface motor-driven XY planar motion stage equipped with a newly developed XYθ_Z surface encoder for sub-micron positioning. The surface motor consists of four linear motors placed on the same surface, two pairs in the XY-axes. The magnetic array and the stator winding of the linear motor are mounted on the platen (the moving element) and the stage base, respectively. The platen can be moved in the X-direction by the X-linear motors, and in the Y-direction by the Y-linear motors. It can also be rotated about the Z-axis if the X- or Y-linear motors generate a moment about the Z-axis. The surface encoder consists of two two-dimensional angle sensors and an angle grid with two-dimensional sinusoidal waves on its surface. The angle grid is mounted on the platen of the stage which is levitated by air-bearings. The angle sensors and the air-bearing pads are fixed on the stage base so that the motion of the platen is not affected by the electronic cables and air hoses. The XY-positions and θ_Z rotation of the platen can be obtained from the angle sensor outputs with resolutions of approximately 20 nm and 0.2′′, respectively. The surface encoder is placed inside the stage so that the stage system is very compact in size. Experimental results indicate that precision positioning can be carried out independently in X, Y and θ_Z with resolutions of 200 nm and 1′′, respectively.     

Understanding the Structural Evolution and Redox Mechanism of a NaFeO2–NaCoO2 Solid Solution for Sodium‐Ion Batteries

Na‐ion batteries have become promising candidates for large‐scale energy‐storage systems because of the abundant Na resources and they have attracted considerable academic interest because of their unique behavior, such as their electrochemical activity for the Fe³⁺/Fe⁴⁺ redox couple. The high‐rate performance derived from the low Lewis‐acidity of the Na⁺ ions is another advantage of Na‐ion batteries and has been demonstrated in NaFe_1/2Co_1/2O₂ solutions. Here, a solid solution of NaFeO₂‐NaCoO₂ is synthesized and the mechanisms behind their excellent electrochemical performance are studied in comparison to those of their respective end‐members. The combined analysis of operando X‐ray diffraction, ex situ X‐ray absorption spectroscopy, and density functional theory (DFT) calculations for Na_{1– x} Fe_1/2Co_1/2O₂ reveals that the O3‐type phase transforms into a P3‐type phase coupled with Na⁺/vacancy ordering, which has not been observed in O3‐type NaFeO₂. The substitution of Co for Fe stabilizes the P3‐type phase formed by sodium extraction and could suppress the irreversible structural change that is usually observed in O3‐type NaFeO₂, resulting in a better cycle retention and higher rate performance. Although no ordering of the transition metal ions is seen in the neutron diffraction experiments, as supported by Monte‐Carlo simulations, the formation of a superlattice originating from the Na⁺/vacancy ordering is found by synchrotron X‐ray diffraction for Na_0.5Fe_1/2Co_1/2O₂, which may involve a potential step in the charge/discharge profiles.     

The effect of hydrogen evolution reaction on conductance quantization of Au, Ag, Cu nanocontacts

We have mechanically fabricated Au, Ag, and Cu nanocontacts in solution under electrochemical potential control. At the hydrogen evolution potential, fractional conductance peaks appeared near 0.5 G(0) (G(0) = 2e(2)/h) in the conductance histogram of Au and Cu. This fractional conductance peak was not observed in the conductance histogram of Ag. In the case of Au nanocontacts in 50?mM H(2)SO(4) solution, a 0.1 G(0) peak appeared in the conductance histogram, as well as the 0.5 G(0) peak. The origin of the fractional conductance peak and its metal dependence are discussed based on previously reported values of metal-hydrogen binding energy, which was estimated by the exchange current density for the hydrogen evolution reaction.     

Organic nanowire-templated fabrication of alumina nanotubes by atomic layer deposition

Alumina nanotubes were fabricated by a template method. Tris-(8-hydroxyquinoline) gallium (GaQ3) organic nanowires were used as a soft template for coating with alumina using an atomic layer deposition technique. The deposition was conducted at 25 degrees C by using trimethylaluminum and distilled water as the precursors of Al2O3. Amorphous alumina nanotubes were obtained after removing the GaQ3 by dissolving in toluene or by heat treatment at 350 degrees C. The amorphous nanotubes could be crystallized by heating at 900 degrees C for 1 h in vacuum.     

Electrochemically grown Pd nanoparticles used for synthesis of carbon nanotube by microwave plasma enhanced chemical vapor deposition

Pd nanoparticles of well-defined shapes with face centered cubic structure were grown electrochemically on silicon substrates with high degree of reproducibility. As direct application of these electrochemically grown Pd nanostructures they have been used as catalyst for the growth of multi wall carbon nanotube (MWCNT). It is observed that the MWCNTs are filled with a Pd based material during growth by microwave plasma enhanced chemical vapor deposition (MPECVD) technique. High-resolution transmission electron microscopy, used to study the material inside MWCNT suggests the formation of PdH0.649 or Pd2Si during the growth of carbon nanotube. Raman spectroscopy has been used to study the structure of the MPECVD grown carbon nanotubes.     

Development of incremental deep drawing process

This paper deals with development of an incremental deep drawing process. On a newly developed incremental deep drawing set-up, the aluminium sheets are formed; the forming is carried out by deep-drawing the blank as in the conventional method but incrementally. Fractures at the punch or die corner in the blank may or may not occur depending on the conditions; the process parameters involved are punch size, punch corner radius, increment in punch displacement, blank holding force or pressure, etc. It is thus shown that different shapes are formed by one set of common tools. It is thereby confirmed that incremental deep drawing is possible without using a particular tool set for a particular shape.     

Suppression of Bone Necrosis around Tooth Extraction Socket in a MRONJ-like Mouse Model by E-rhBMP-2 Containing Artificial Bone Graft Administration

Medication-related osteonecrosis of the jaw (MRONJ) is related to impaired bone healing conditions in the maxillomandibular bone region as a complication of bisphosphonate intake. Although there are several hypotheses for the onset of MRONJ symptoms, one of the possible causes is the inhibition of bone turnover and blood supply leading to bone necrosis. The optimal treatment strategy for MRONJ has not been established either. BMP-2, a member of the TGF-β superfamily, is well known for regulating bone remodeling and homeostasis prenatally and postnatally. Therefore, the objectives of this study were to evaluate whether cyclophosphamide/zoledronate (CY/ZA) induces necrosis of the bone surrounding the tooth extraction socket, and to examine the therapeutic potential of BMP-2 in combination with the hard osteoinductive biomaterial, β-tricalcium phosphate (β-TCP), in the prevention and treatment of alveolar bone loss around the tooth extraction socket in MRONJ-like mice models. First, CY/ZA was intraperitoneally administered for three weeks, and alveolar bone necrosis was evaluated before and after tooth extraction. Next, the effect of BMP-2/β-TCP was investigated in both MRONJ-like prevention and treatment models. In the prevention model, CY/ZA was continuously administered for four weeks after BMP-2/β-TCP transplantation. In the treatment model, CY/ZA administration was suspended after transplantation of BMP-2/β-TCP. The results showed that CY/ZA induced a significant decrease in the number of empty lacunae, a sign of bone necrosis, in the alveolar bone around the tooth extraction socket after tooth extraction. Histological analysis showed a significant decrease in the necrotic alveolar bone around tooth extraction sockets in the BMP-2/β-TCP transplantation group compared to the non-transplanted control group in both MRONJ-like prevention and treatment models. However, bone mineral density, determined by micro-CT analysis, was significantly higher in the BMP-2/β-TCP transplanted group than in the control group in the prevention model only. These results clarified that alveolar bone necrosis around tooth extraction sockets can be induced after surgical intervention under CY/ZA administration. In addition, transplantation of BMP-2/β-TCP reduced the necrotic alveolar bone around the tooth extraction socket. Therefore, a combination of BMP-2/β-TCP could be an alternative approach for both prevention and treatment of MRONJ-like symptoms.