Material and velocity effects on cavitation erosion pitting

Cavitation erosion during the incubation period was investigated via pitting tests conducted on three different materials: an Aluminum alloy, a Nickel Aluminum Bronze alloy and a Duplex Stainless Steel. Pitting tests were conducted in a cavitation tunnel in the velocity range 45–90 m/s at a constant cavitation number. The test section was made of a straight nozzle 16 mm in diameter discharged into the radial 2.5 mm space between two flat walls. Cavitation appears in the form of a toroidal cavity attached to the nozzle exit and damage on the samples facing the nozzle is concentrated in a circular ring centered in the cavity closure region. The exposure time was adjusted to avoid pit overlapping. The material surface was examined using a conventional contact profilometer which allowed us to identify the pits, count them, and measure their main characteristics such as depth, surface area, and volume. From these the pitting rate, the coverage rate, and the depth of deformation rate were defined. Pits were classified according to their diameter. For all materials and operating conditions, pitting rate appears to follow an exponential law in relation to the pit diameter. This law depends upon two parameters only, which were identified as the coverage time τ (i.e. the time required for the surface to be covered by erosion pits) and a characteristic pit diameter δ, which corresponds to the pits whose contribution to the coverage process is the highest. Scaling laws for pitting were derived accounting for both material properties and flow velocity, and a procedure to make pitting test results non-dimensional is proposed. The influence of the material on pitting test results was analyzed. It is shown that the damage is not correlated in simple terms with the elastic limit determined from conventional tensile tests and it is conjectured that other parameters such as the strain rate might play a significant role and should be included in the analysis. The effect of flow velocity on both parameters τ and δ was analyzed and a classical power law was found for the influence of the flow velocity on pitting rate for all three materials. Finally, some analysis and discussion is given concerning distributions of pit volume and pit depth.     

Dynamic Features of the Rumen Metabolism of Linoleic Acid,Linolenic Acid and Linseed Oil Measured in Vitro

The lipid quality of ruminant products is largely determined by the extent of rumen microbial biohydrogenation (BH) of polyunsaturated fatty acids (FAs) and the substances formed thereby. In vitro batch incubations with mixed rumen bacteria were tracked over 24 h to characterize the profiles and kinetics of the BH products from three lipid sources: pure linoleic acid (c9,c12–18:2), pure linolenic acid (c9,c12,c15–18:3) and linseed oil (mainly c9,c12,c15–18:3 in triacylglycerols). After 24 h of incubation biohydrogenation was more complete for c9,c12–18:2, which gave mainly stearic acid (18:0), than for c9,c12,c15–18:3, which yielded mainly trans-18:1 FAs. This suggests inhibition of the final BH step (18:1 to 18:0). Incubations of c9,c12–18:2 resulted in high levels of carbon 10- and 12-desaturated 18:1, t10,c12- and c9,t11-CLAs. Incubations of c9,c12,c15–18:3 resulted in high levels of t11–18:1, carbon 13- and 15-desaturated 18:1 as well as t11,c15–18:2 and 11,13-CLAs. A comparative study of linolenic acid and linseed oil kinetics revealed that the BH process was not significantly slowed by the esterification of polyunsaturated FAs, but may have been limited by the isomerization step in which the cis12 double bond goes to the trans11 position. The disappearance rates of c9,c12–18:2 and c9,c12,c15–18:3 ranged from 23.6 to 44.6%/h. The wide variety of BH intermediates found here underlines the large number of possible BH pathways. These data help provide a basis for dynamic approaches to BH processes.     

Reactive surfactants in heterophase polymerization. XVII. Influence of the surfactant on the mechanical properties and hydration of the films

In the context of a European union‐supported network on “Reactive Surfactants for Heterophase Polymerization,” different polymerizable surfactants (surfmers) have been synthesized and engaged in the emulsion polymerization of styrene, butyl acrylate, and acrylic acid. The thermomechanical properties of films cast from these different latices are reported in this article. The evolution of the mechanical properties with temperature and the effect of water molecules on these properties are studied. We observed that the studied surfactants do not influence the properties of the dry films. However, some differences due to grafting of reactive surfactants appeared when the films were wet. The amount of water uptake is drastically decreased when only reactive surfactants are present in the film. Concerning the mechanical behavior of the wet films, a decrease of the plastic flow stress is observed for all the samples whatever the nature of the surfactant (reactive or conventional). Hence, calorimetric measurements and dynamic mechanical analysis are used to identify the possible mechanisms that induce the change in the mechanical behavior of the latex films. In the case of reactive surfactant grafted to the polymer, the very low value of water uptake is accompanied by a plasticization of the polymer. In contrast, no plasticizing effect is observed in the case of nonreactive surfactant, even if the amount of water is very large. Finally, the tensile behavior of the styrene–butyl acrylate copolymer versus temperature is analyzed in the frame of the quasi point defects (qpd) model. Both rubber elasticity and chain orientation effects are taken into account to describe the behavior laws at large extensions (i.e., ? ≈ 1.2). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1686–1700, 2002; DOI 10.1002/app.10548     

Synthesis and Antiviral Evaluation of 3′-Fluoro-4′-modified-5′-norcarbocyclic Nucleoside Phosphonates

The synthesis and anti-HIV evaluation of hitherto unknown 3′-fluoro-5′-norcarbocyclic nucleoside phosphonates bearing adenine with modifications at the 4′ position (ethynyl, vinyl, ethyl, hydroxymethyl) is described. One of the synthesized compounds was found to be an inhibitor of HIV-1 replication, but with moderate efficiency relative to (R)-9-(2-phosphonylmethoxypropyl)adenine ((R)-PMPA, tenofovir), with no concomitant cytotoxicity.     

Electrical contact resistance between stainless steel bipolar plate and carbon felt in PEFC: A comprehensive study

Bipolar plate represents a key component of Proton Exchange Membrane Fuel Cell (PEFC) with several essential functions, among them the electric connection of elementary cells. Usually made of graphite, this component is studied worldwide in order to develop a commercially viable alternative: different ways have been being investigated, and to date, despite corrosion issues, stainless steel (SS) appears as a good candidate material, but its Electrical Contact Resistance (ECR) can reach unacceptable values when exposed to PEFC environment. This paper offers a comprehensive study of the parameters acting on ECR when using uncoated SS in PEFC: roughness, which influences the surface contact area with carbon baking, bulk composition of the alloy, which influences only partly the nature of passive films, and the composition and structure of passive films, strongly modified by surface treatments and ageing conditions.     

The effect of a scattering layer on the edge output of a luminescent solar concentrator

The effect of adding white scattering layers to the bottom side of luminescent solar concentrator waveguides is evaluated. It is determined that adding a rear scatterer separated from the waveguide by an air gap results in a large increase of energy output from the waveguides, and this enhancement persists over long (>30 cm) distances, although the magnitude of the enhancement decreases with distance. An attached scatterer resulted in the greatest improvement of light output for short (∼6 cm) distances, but actually reduced edge emissions over longer distances. We provide estimates for the relative contribution of dye-emitted light and scattered light to the total waveguide emission, as well as distinguishing between the contributions of direct and indirect scattering of light to the total output as a function of dye content of the waveguides.     

A hierarchical approach for planning a multisensor multizone search for a moving target

This paper deals with a well-known problem in the general area of search theory: optimize the search resources sharing so as to maximize the probability of detection of a (moving) target. However, the problem we consider here considerably differs from the classical one. First, there is a bilevel search planning and we have to consider jointly discrete and continuous optimization problems. To this perspective original methods are proposed within a common framework. Furthermore, this framework is sufficiently general and versatile so as to be easily and successfully extended to the difficult problem of the multizone multisensor search planning for a Markovian target.     

RFID behavior study in enclosed marine container for real time temperature tracking

The performance of radio waves in open environments has been studied for years. In contrast, the behavior of Radio Frequency Identification (RFID) inside metal enclosed areas is not yet understood. This research project focuses on the 3-D mapping of RFID signal strength inside a 12 m refrigerated marine container instrumented with three different types of radio frequency (RF) emitters: 915 MHz reader; 2.45 GHz reader and 433 MHz RF transmitter. The main goal is to find a frequency/configuration that would allow real time reading of the temperature in a shipment of perishable products using RFID. Only one frequency and one antenna were used at a time. The RF transmitter antenna was mounted at two different places inside the container; at the top of the front wall (facing back) and on the ceiling in the middle of the container (facing down). The signal strength was acquired by a spectrum analyzer and its antenna was mounted on a small electric cart inside the container. The cart was programmed to move along the length of the container and stop repeatedly, allowing three automated measures per position. All data were analyzed in terms of power level and attenuation. The maps showed that the RFID antenna positioned at the front of the container delivered slightly better results than the one in the middle of the ceiling. The results showed a significantly higher performance at the 433 MHz level. This article was presented at Food Processing Automation Conference, American Society of Agricultural and Biological Engineering (ASABE), Providence, RI, June 28–29 2008.