Improved performances of a S-SEED using extremely shallowquantum-wells and asymmetric Fabry-Perot cavity structure

The authors report significantly improved performances of a symmetric self-electrooptic-effect device (S-SEED), with high on-off contrast ratio (>30:l) and large optical bistability loop widths (ΔP=44%) at an applied bias of V_a=0 V, i.e., with no power supply. The S-SEED is made of extremely shallow quantum wells (ESQWs) in an asymmetric Fabry-Perot (AFP) cavity structure. At V_a =5 V ΔP increased by up to 95%, preserving the high contrast ratio. The reflectivity changes at V_a=0 and 5 V were about 15% and 30%, respectively. These are believed to be the largest values ever reported for such structures     

Acidogenic fermentation of blended food‐waste in combination with primary sludge for the production of volatile fatty acids

The performance of a laboratory‐scale anaerobic acidogenic fermenter fed with a mixture of blended kitchen food‐waste and primary sludge from a sewage treatment plant was investigated for the production of volatile fatty acids (VFA). The operating variables for acidogenic fermentation were kitchen food‐waste content (10 and 25 wt %), hydraulic retention time (HRT: 1, 3 and 5 days), temperature (ambient: 18 ± 2 °C, and mesophilic: 35 ± 2 °C) and pH (varied from 5.2 to 6.7). The experimental results indicated that effluent VFA concentrations and VFA production rates were higher at ambient temperature than at mesophilic conditions. The net amount of VFA with 10 wt % food‐waste increased up to 920 mg dm^?3 with an increase of HRT, but contrasting results (a decrease of 2610 mg dm^?3) were found due to the conversion of VFA into biogas in the case of 25 wt % food‐waste, which increased significantly at HRT of 3–5 days. In terms of biogas composition (CO₂ and CH₄), the organic matter was converted into CO₂ through the oxidative pathway by facultative species at low temperature while mesophilic temperature and optimum pH (6.3–7.8) played a pivotal role in increasing rate of conversion of VFA into biogas by methanogenesis. Rates of VFA production and their conversion are dependent on the food‐waste content in the mixture. Yet, the higher concentration of food‐waste (25% compared with 10%) did not produce VFA proportionally due to the increased rate of conversion of VFA into gaseous products. The maximum VFA production rate (0.318 g VFA_produced g^?1 VS_fed day^?1) was achieved in the 10 wt % food‐waste at ambient temperature and at a 5‐day HRT. Copyright © 2005 Society of Chemical Industry     

Use of a neural network to link AFM etch patterns to plasma parameters

Plasmas play a critical role in depositing thin films or etching fine patterns while manufacturing integrated circuits. A new model for plasma diagnosis is presented. This was accomplished by linking atomic force microscopy (AFM) to plasma parameters using a neural network. Experimental AFM data were collected during the etching of silicon oxynitride films in C₂F₆ inductively coupled plasma. Surface roughness of etched patterns was characterized by means of discrete wavelet transformation. This led to the construction of three vertical (type I), diagonal (type II), and horizontal (type III) wavelet coefficient-based models. The performance of diagnosis models was evaluated in terms of the prediction and recognition accuracies. Both accuracies were optimized as a function of the number of hidden neurons. Comparisons revealed that the type I model yielded the largest recognition and the smallest prediction error. This was demonstrated even under stricter monitoring conditions. More improved diagnosis is expected by enhancing AFM resolution.     

Effects of reducing and oxidizing atmospheres on the PTCR characteristics of porous n-BaTiO3 ceramics by adding polyethylene glycol

Donor doped BaTiO₃ (n-BaTiO₃) ceramics were fabricated by adding polyethylene glycol (PEG) at 20 wt %. The effects of reducing and oxidizing atmospheres on the PTCR characteristics of the porous n-BaTiO₃ ceramics were investigated. The PTCR characteristics of the porous n-BaTiO₃ ceramics is strongly affected by chemisorbed oxygen at the grain boundaries and are recovered as the atmosphere is changed from the reducing gas to oxidizing gas. The low room-temperature resistivity of the porous n-BaTiO₃ ceramics in reducing atmospheres may be caused by the decrease in potential barrier height, which originates from an increase in the number of electrons owing to the desorption of chemisorbed oxygen atoms at the grain boundaries. In addition, the high room-temperature resistivity of the porous n-BaTiO₃ ceramics in oxidizing atmospheres may be caused by the increase in potential barrier height, which results from the adsorption of chemisorbed oxygen atoms at the grain boundaries.     

A 44-GHz monolithic waveguide plane-wave amplifier with improvedunit cell design [using pHEMTs]

A 44-GHz monolithic waveguide plane-wave amplifier (PWA) with improved unit cell design is presented in this paper. The unit cell is a two-stage direct-coupled design and satisfies size, bistability, and stability requirements of the waveguide PWA. The ultra-compact unit cell had a cell size of 0.8 mm², and showed a small-signal gain of 8 dB and an output power of 15 dBm at 44 GHz with a corresponding dc-to-RF efficiency of 10%. A monolithic waveguide PWA using these unit cells showed a “flange-to-flange” gain of 5 dB, an output power of 0.3 W, and an efficiency of 2% at 44 GHz     

Breakdown probabilities for thin heterostructure avalanche photodiodes

The recurrence theory for the breakdown probability in avalanche photodiodes (APDs) is generalized to heterostructure APDs that may have multiple multiplication layers. The generalization addresses layer-boundary effects such as the initial energy of injected carriers as well as the layer-dependent profile of the dead space in the multiplication region. Reducing the width of the multiplication layer serves to both downshift and sharpen the breakdown probability curve as a function of the applied reverse-bias voltage. In structures where the injected carriers have an initial energy that is comparable to the ionization threshold energy, the transition from linear mode to Geiger-mode is more abrupt than in structures in which such initial energy is negligible. The theory is applied to two recently fabricated Al/sub 0.6/Ga/sub 0.4/As-GaAs heterostructure APDs and to other homostructure thin GaAs APDs and the predictions of the breakdown-voltage thresholds are verified.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

Strength and fracture toughness of nano and micron-silica particles bidispersed epoxy composites: evaluated by fragility parameter

In this study, we discuss the composition effect of 240 nm and 1.56 μm-silica particles on strength and fracture toughness by examining two parameters, fragility and glass transition temperature, that were derived from the thermo-viscoelasticity measurements. Experimental results showed that the composites had a lower fragility with higher strength and fracture toughness as the content of nanoparticles was increased regardless of glass transition temperature. The improvement in mechanical properties from adding nanoparticles was definitely explained by the fragility represented the heterogeneity in polymer matrix, and this was related to the interaction between particles and matrix. The fragility was found to be an effective parameter for evaluating strength and fracture toughness of epoxy composite containing a bidispersion of nano and micron-silica particles.