A 950-MHz rectifier circuit for sensor network tags with 10-m distance

This paper presents a 950-MHz wireless power transmission system and a high-sensitivity rectifier circuit for ubiquitous sensor network tags. The wireless power transmission offers a battery-life-free sensor tag by recharging the output power of a base station into a secondary battery implemented with the tag. For realizing the system, a high-sensitivity rectifier with dynamic gate-drain biasing has been developed in a 0.3-/spl mu/m CMOS process. The measurement results show that the proposed rectifier can recharge a 1.2-V secondary battery over -14-dBm input RF power at a power conversion efficiency of 1.2%. In the proposed wireless system, this sensitivity corresponds to 10-m distance communication at 4-W output power from a base station.     

Modeling of debris cooling with annular gap in the lower RPV and verification based on ALPHA experiments

For severe accident assessment in a light water reactor, heat transfer models in a narrow annular gap between the overheated core debris and the reactor pressure vessel (RPV) are important for evaluating RPV integrity and emergency procedures. Using existing data, the authors developed heat transfer models on the average critical heat flux (CHF) restricted by countercurrent flow limitation (CCFL) and local boiling heat fluxes, and showed that the average CHF depended on the steam–water flow pattern in the narrow gap and that the local heat fluxes were similar to the pool boiling curve. We evaluated the validity of heat transfer models by simple calculations for ALPHA experiments performed at Japan Atomic Energy Research Institute. Calculated results showed that heat fluxes on the crust surface were restricted mainly by thermal resistance of the crust after the crust formation, and emissivity on the crust surface did not have much effect on the heat fluxes. The calculated vessel temperature during the heat-up process and peak vessel temperature agreed well with the measurements, which confirmed the validity of the average CHF correlation. However, the vessel cooling rate was underestimated mainly due to underestimation of the gap size.     

Balance between genetic search and local search in memetic algorithms for multiobjective permutation flowshop scheduling

This paper shows how the performance of evolutionary multiobjective optimization (EMO) algorithms can be improved by hybridization with local search. The main positive effect of the hybridization is the improvement in the convergence speed to the Pareto front. On the other hand, the main negative effect is the increase in the computation time per generation. Thus, the number of generations is decreased when the available computation time is limited. As a result, the global search ability of EMO algorithms is not fully utilized. These positive and negative effects are examined by computational experiments on multiobjective permutation flowshop scheduling problems. Results of our computational experiments clearly show the importance of striking a balance between genetic search and local search. In this paper, we first modify our former multiobjective genetic local search (MOGLS) algorithm by choosing only good individuals as initial solutions for local search and assigning an appropriate local search direction to each initial solution. Next, we demonstrate the importance of striking a balance between genetic search and local search through computational experiments. Then we compare the modified MOGLS with recently developed EMO algorithms: the strength Pareto evolutionary algorithm and revised nondominated sorting genetic algorithm. Finally, we demonstrate that a local search can be easily combined with those EMO algorithms for designing multiobjective memetic algorithms.     

Current dependence of performance of TES microcalorimeters and characteristics of excess noise

We are developing transition edge sensor (TES) microcalorimeter arrays for future Japanese astronomy missions. Although 6.6 eV energy resolution for 5.9 keV and 74 μs decay time are achieved, our energy resolution was limited by the excess noise of unknown origin. The dominant noise showed 1/R dependence and it only appeared when the current through the TES, I, is larger than 10 μA. This is explained if we assume a constant voltage noise source with a level of 2(4kT_CR_n)^1/2. We also investigated the influence of I on the TES performance and found the TES sensitivity is reduced when the ratio of current to the critical current I/I_C is large. It can explain the reduction of observed when operated without a magnetic shield. We also found a strong correlation between I_C and or the baseline width. Thus, we conclude that I_C is an essential parameter for the TES performance.     

Ceramic matrix composites derived from CrSi2-filled silicone polycyclic network

Ceramic matrix composites (CMC) were prepared by the active-filler-controlled polymer pyrolysis, using a siloxane polycyclic network filled with CrSi₂. The starting CrSi₂-filled polysiloxane was pyrolyzed in both nitrogen and argon atmospheres, up to 1450°C. During the pyrolysis in nitrogen atmosphere, the CrSi₂ particles reacted with N₂, and also with carbon from the preceramic polymer binder, still complete consumption of the filler particles. Such reactions led to a dramatic change in the composition and microstructure of the resulting ceramic monoliths, which displayed linear expansion of 1.7%. In argon atmosphere, the CrSi₂ particles acted as inert filler during the pyrolysis process. The final CMC compositions obtained in N₂ and Ar atmospheres were Cr_0.62C_0.25N_0.03-Si₃N₄-Cr₃C₂ and SiO_xC_y-SiC-CrSi₂, respectively.     

Reduction of defects and improvement in the performance of blue phosphor for thick‐dielectric electroluminescent displays using Color‐by‐Blue

Abstract— Defect‐free large‐area inorganic thick‐dielectric EL (TDEL) displays using Color by Blue (CBB) technology have been successfully developed. We have achieved the world's highest blue‐phosphor luminance of 900 cd/m² for a single‐pixel device by using CBB and by optimizing the e‐beam gun configuration and the flow rate of H₂S in the vacuum chamber. By analyzing the defects on panels with triple‐pattern phosphors and CBB panels, we also found that the number of defects on CBB panels can be drastically reduced compared with those on triple‐pattern panels. The defect‐free 17‐in. VGA CBB panels show better characteristics, a high peak luminance of 600 cd/m² and a high contrast ratio of 1000:1, compared with those of triple‐pattern panels.     

A two-degree-of-freedom motor-powered gait orthosis for spinal cord injury patients

A number of orthoses have been developed to restore stance and walking in paraplegic subjects. Compliance, however, has been limited, mainly owing to walking effort. Use of the forces produced by actuators is an effective way to solve the problem of the considerable effort required for orthotic gait, namely high muscular effort and high energy expenditure. The purpose of the present study was to investigate the effects of assistance by external actuators on the orthotic gait of spinal cord injury (SCI) patients. Two kinds of linear actuator were developed by using direct current (d.c.) motors for assisting the knee and hip joint of a gait orthosis. They were mounted on the knee and hip joint of a commercial advanced reciprocating gait orthosis (ARGO), and a new two-degree-of-freedom externally powered gait orthosis was thus developed. The orthosis was assessed through inter-subject experiments on five male adult complete SCI patients. Owing to the short training period available for the assisted gait, simultaneous operation of both joint actuators was not conducted: either the knee actuation or the hip actuation was executed only. Thus, the knee actuator and the hip actuator were assessed with a T12 subject and with subjects for T5, T8, T11, and T12 respectively. The motions of the gaits, assisted by the linear actuators, were measured by a Vicon 370 system, and the general gait parameters and compensatory motions were evaluated. Results demonstrated that (a) all subjects could walk without falling, assisted either by the knee or the hip actuator; (b) both the knee and hip joint actuator increased the gait speed and the step length; (c) the knee flexion produced by the orthosis improved the dynamic cosmesis of walking; and (d) lateral compensatory motions as well as vertical ones tended to decrease when the hip joint was assisted, which could contribute to a reduction in walking effort.     

Macroscopic and microscopic changes in the surface layers of annealed and case-hardened steel rollers due to rolling contact

Measurements of the residual stress and observations of the microstructure at the surface and in the subsurface of rollers were performed during rolling contact fatigue tests of annealed 0.45% carbon steel and case-hardened nickel-chromium steel rollers. Compressive residual stresses in annealed rollers were induced by the rolling contact. With case-hardened rollers they were induced by heat treatment prior to the rolling contact fatigue tests. After the rolling contact fatigue tests the compressive residual stresses on the surface of the annealed rollers and in the subsurface of the case-hardened rollers relaxed; a characteristic substructure was formed by the stress cycles, which caused surface failure. It was confirmed that the microcracks leading to surface failure initiate on the surfaces of annealed rollers and in the subsurface of case-hardened rollers.     

Effect of chitosan-gluconic acid conjugate/poly(vinyl alcohol) cryogels as wound dressing on partial-thickness wounds in diabetic rats

We previously developed chitosan cryogels from chitosan-gluconic acid conjugate without using toxic additives for wound care. In this study, we improved physiological characteristics of the previous cryogels by incorporating poly(vinyl alcohol) that also form cryogels. Mechanical strength of the cryogels was more than two times higher than that of the previous cryogels. Furthermore, the incorporation of poly(vinyl alcohol) enhanced water retention and resistance to degradation of the gels by lysozyme. The cryogels retained the favorable biological properties of the previous cryogels that they accelerate infiltration of inflammatory cells into wound sites. Time period for repairing 50 % of initial area of partial-thickness skin wound treated with the cryogels (4.0 ± 1.1 days) was shorter than those with gauze (6.5 ± 0.3 days) or a commercial hydrogel dressing (5.7 ± 0.3 days). Finally, we confirmed that incorporation of basic fibroblast growth factor into the cryogels was effective to further accelerate wound healing (2.7 ± 1.0 days). These results demonstrate that the cryogels in this study are promising for wound care.