Processing to optimize the strength of heavily drawn Cu-Nb alloys

Heavily drawn Cu-Nb alloys display quite high ultimate tensile strengths. A modification to the consumable arc-casting technique used to prepare these alloys is shown to decrease the as-cast niobium dendrite diameter,t ₀, and also increase strength. Evaluation of strength, niobium filament spacing and thickness data show that strength varies with as-cast niobium dendrite size as somewhere betweent _o ^–0.36 tot _o ^–0.50 . Splat-cooling techniques demonstrate that minimum niobium dendrite sizes as small as 0.22m are possible. These sizes are over a factor of 10 smaller than has been achieved by consumable arc casting, and it is therefore suggested that processing rapidly solidified powders of Cu-Nb alloys should have significant advantages for preparing high-strength heavily drawn Cu-Nb alloys.     

Extraction technique for the determination of oxygen-18 in water using preevacuated glass vials

The need for a rapid, inexpensive technique for routine 18O/16O extraction from water has arisen recently through applications in the medical sciences and in hydrology. The traditional experimental technique for determining the oxygen isotope composition of water, the CO2-H2O equilibration method, is tedious, time consuming, and involves the use of custom-made glass apparatus. Furthermore, because of potential memory effects from one sample to the next, the glassware needs to be thoroughly cleaned between runs. A few attempts have been made to improve upon the method. Attempts to analyze water directly in the source of the mass spectrometer produced large memory effects and questionable results. Commercially available apparatus for automated extraction of 18O/16O from water is generally prohibitively expensive and often is designed to interface only with the manufacturer's own mass spectrometer. The method described in this paper utilizes inexpensive, off-the-shelf, preevacuated, glass vials. Preevacuated vials have been used by others for the isotopic analysis of breath CO2 and are well tested. The vials can be purchased in bulk from scientific apparatus suppliers at a relatively low cost. These are coupled with a simplified extraction line consisting of a stainless steel syringe needle and a glass cold trap. Vials are filled with CO2 and H2O and shaken in a constant-temperature water bath for at least 90 min. Since the vials are discarded after use, no cleaning is necessary, essentially eliminating any memory effect. Reproducibility is generally better than +/- 0.05%. The only reagents required are gaseous CO2 for equilibration, a dry ice/alcohol mixture for trapping water, and liquid nitrogen for transferring the CO2.     

The dielectric response of doped semiconducting glasses

Measurements are reported of the dielectric properties of two semiconducting glasses of composition SiO₂ · Na₂O with admixtures of Sb_{2O 5} and SnO₂, covering a wide range of temperatures and a range of six decades of frequency 10^–2 to 10⁴ Hz. Both glasses show a gradual evolution of growing low frequency dispersion (LFD) with increasing temperature, with both the real and imaginary components of the complex susceptibility following a power law of the type ^n–1, with n 1 at the lowest frequencies. There are also clear indications of reversible phase transitions taking place which manifest themselves by changes in the spectral shape of the dielectric response.     

Characterization and Reconstitution of Human Lipoyl Synthase (LIAS) Supports ISCA2 and ISCU as Primary Cluster Donors and an Ordered Mechanism of Cluster Assembly

Lipoyl synthase (LIAS) is an iron–sulfur cluster protein and a member of the radical S-adenosylmethionine (SAM) superfamily that catalyzes the final step of lipoic acid biosynthesis. The enzyme contains two [4Fe–4S] centers (reducing and auxiliary clusters) that promote radical formation and sulfur transfer, respectively. Most information concerning LIAS and its mechanism has been determined from prokaryotic enzymes. Herein, we detail the expression, isolation, and characterization of human LIAS, its reactivity, and evaluation of natural iron–sulfur (Fe–S) cluster reconstitution mechanisms. Cluster donation by a number of possible cluster donor proteins and heterodimeric complexes has been evaluated. [2Fe–2S]-cluster-bound forms of human ISCU and ISCA2 were found capable of reconstituting human LIAS, such that complete product turnover was enabled for LIAS, as monitored via a liquid chromatography–mass spectrometry (LC–MS) assay. Electron paramagnetic resonance (EPR) studies of native LIAS and substituted derivatives that lacked the ability to bind one or the other of LIAS’s two [4Fe–4S] clusters revealed a likely order of cluster addition, with the auxiliary cluster preceding the reducing [4Fe–4S] center. These results detail the trafficking of Fe–S clusters in human cells and highlight differences with respect to bacterial LIAS analogs. Likely in vivo Fe–S cluster donors to LIAS are identified, with possible connections to human disease states, and a mechanistic ordering of [4Fe–4S] cluster reconstitution is evident.     

Some aspects of the analysis of coal by X-ray fluorescence spectroscopy

Bituminous coal samples from 84 distinct sources were analysed by conventional British Standards (BS) methods for phosphorus, sulphur, chlorine, ash and the ash-forming elements (calcium, silicon, aluminium, iron, sodium, magnesium, potassium, titanium and manganese). In most cases four determinations were made per element per source. Samples were crushed to ?212 μm (72 BS mesh) and pressed into aluminium cups at 20 t in^?2 (309 MPa) without binder or backing. Two pellets from each sample were analysed by wave-length dispersive X-ray fluorescence techniques, using a spectrometer equipped with a rhodium rube; the X-ray count took 60 s. The X-ray results were calibrated against the conventional results using multiple regression. The accuracy obtained was comparable with routine ‘wet chemical’ techniques. The X-ray technique is suitable for the routine determination of large numbers of samples.     

High resolution STEM/EDX spectral imaging to resolve metal distributions within ∼100 nm combustion generated ash particles

Ultrafine ash particles play an important role in establishing a sticky inner deposit layer on heat transfer surface for power plants, but it is still unclear whether a thin surface alkali coating on these ultrafine particles might control this deposition behavior. In this research, we used a high resolution FE-TEM/STEM equipped with twin SDD EDX detectors for high X-ray detection efficiency, to determine the presence and absence of surface enrichment of alkali metals on ultrafine solid fuel ash samples that had low bulk alkali compositions but high deposition rates. Results from two types of combustion generated nano-sized ash particles are presented. One was from the oxy-combustion of pulverized bituminous coal, the other from oxy-combustion of pulverized rice husks, both being burned in a 100?kW rated down-flow laboratory combustor. Elemental mapping results from STEM/EDX uncovered some surface enrichment of alkali metals in ultrafine ash particles, where it existed, as it did for combustion of rice husks. However, it was not able to discern similar alkali metal surface enrichment for the bituminous coal ultrafines that had resulted in even higher deposition rates. Since deposition rates from both of these cases lie on the same correlation with PM₁, one can conclude that although surface enrichment of alkali metals is present for some ～100?nm particles, it is not a prerequisite to achieve high inner surface deposition rates. This is in contrast to prevailing theories that point to alkali metals as “bad actors” as far as the sticky inner deposition rate is concerned.

Copyright © 2019 American Association for Aerosol Research     

Evidence for the Participation of Singlet Oxygen in the Vat–dye Photosensitized Degradation of Cellulose

A study has been made of the vat–dye photosensitized degradation of cellulose. Whilst the part played by the dyes in direct hydrogen abstraction from a cellulose substrate cannot be overlooked, it is apparent that the role played by singlet oxygen is important. The ability of a dye to produce singlet oxygen has been studied by measuring the amount of tetraphenylcyclopentadienone the dye can photo–oxidize. It would appear that the singlet oxygen is initially formed in its high energy g state by energy transfer from the triplet state of the dye to ground state molecular oxygen. Luminescence spectroscopy has been employed in order to gain information about the excited state energies of the dye molecules, and an electron spin resonance study of the dyes in rigid media has been carried out in order to obtain information about the triplet state.     

In Situ Processing of Silicon Carbide Layer Structures

A novel route to low-cost processing of silicon carbide (SiC) layer structures is desribed. The processing involves pressureless liquid-phase cosintering of compacted power layers of SiC, containing alumina (Al₂O₃) and yttria (Y₂O₃ sintering additives to yield and yttrium aluminum garnet (YAG) second phase. By adjusting the β:α SiC phase ratios in the individual starting powders, alternate layers with distinctively different microstructures are produced: (i) "homogeneous" microstructures, with fine equiaxed SiC grains, designed for high strength; and (ii) "heterogeneous: microstructures with coarse and elongate SiC grains, designed for high toughness. By virtue of the common SiC and YAG phases, the interlayer interfaces are chemically compatible and strongly bonded. Exploratory Hertzian indetation tests across a bilayer interface confirm the capacity of the tough heterogeneous layer to inhibit potentially dangerous cracks propagating through the homogeneous layer. The potential for application of this novel processing approach to other layer architectures and other ceramic systems is considered.     

Modeling solute diffusion in aqueous polymer solutions

There are numerous models describing solute diffusion in polymer solutions. An analysis of these models demonstrates that none can provide a consistent explanation of the phenomenon observed for solutes that can be modeled as essentially solid spheres. For this reason, a new model based on a physical obstruction approach is presented. In this model, solute movement in the presence of polymer chains is assumed to be governed by the probability of the solute molecule encountering a series of openings between the chains larger than its hydrodynamic radius. The model is tested against data taken from the literature for a series of polymer solutions and solute probes and found to provide good agreement to the effects of solute size, polymer concentration, and polymer flexibility.     

Determination of diffusion coefficients of water in cellulose acetate membranes

The determination of the diffusion coefficient for water in various porosity cellulose acetate membranes by a gravimetric method, using a humidified carrier gas, is described. It was found to be impossible to obtain meaningful results for very porous membranes, although dense membranes gave limiting values of diffusion coefficient at high carrier gas velocities. This phenomenon is explained in terms of the dissipation of the heat of sorption by the forced convection provided by the carrier gas. The variation of diffusion coefficient with concentration of water in dense cellulose acetate is explained in terms of clustering of water molecules in the polymer at high concentration.