Production of rapidly solidified Al/SiC composites

Rapidly solidified metal matrix composites have been produced on a laboratory scale either by (1) melt spinning a composite after introduction of the ceramic phase and extrusion of the flakes obtained, or (2) blending melt-spun powder (basic alloy) with the ceramic phase and subsequent extrusion. AlMg(Si) alloys were used as matrix material while SiC particles with diameters of 3 or 20 m were used as the ceramic phase. For the composites prepared by route 1 it was found that the basic alloy was reinforced by the addition of 3 m particles whereas for the 20m particles reinforcement was observed only for very ductile matrices. The bond between SiC particles and matrix was good. A diffusion and wetting bond was formed. For the composites prepared by route 2 it was found that reinforcement did not occur and that the bond between particles and matrix was weak. Debonding of the particles took place in the case of tensile fracture. The advantage of a rapidly solidified matrix for these composites is that relatively high ductilities are combined with good reinforcement effects. Prior contact of the ceramic phase and the aluminium melt is needed for a good bond between SiC and the matrix material. It is concluded that route 1 should be preferred for the production of rapidly solidified aluminium matrix composites.     

On the solubility of aluminum in cryolitic melts

The solubility of aluminum in NaF-AlF₃-Al₂O₃ melts with various additives was found to increase with increasing NaF/AlF₃ molar ratio (CR) and increasing temperature and to decrease with additions of A1₂O₃, CaF₂, MgF₂, and LiF to the melts. With the use of literature data for the activities of NaF and A1F₃ in cryolitic melts, three dissolution reaction models were found to give a good fit to the experimental solubility data. According to the most probable of these models the total concentration of dissolved aluminum (aluminum and sodium species) is given by c_Al = c_Na(diss) + c_AlF2- + c_Al2F3- + c_Al3F4- + c_Al4F5- In NaF rich melts, aluminum will dominantly dissolve as sodium, while at cryolite ratios commonly used in aluminum electrowinning (CR = 2.25 to 2.7) the AlF _-2 ^- -ion is the predominant dissolved metal species. Other species (A1₂F₃ ^-, A1₃F₄-, A1₄F₅-) were found to be of some significance only in melts with high excess A1F₃ (CR < 2).     

Fourier Transform Spectrometer for the 1 to 10mm region

A Fourier Transform Spectrometer using a 250 Watt Mercury lamp, a lamellar grating and a pumped He-cooled detector is applied to the millimeter wave spectral region. The pure rotation spectrum of CH₂F, the transmission of graphite particles in a cloud chamber, the interference on round copper dots and the absorption of iron whiskers have been observed.     

The effect of appraisers in estimating metabolic rate with the Edholm scale

A study was made of the appraisers' effect on the estimation of metabolic rate with the Edholm scale and a table of the ISO 7243 heat stress standard. The appraisers, five experienced and five inexperienced persons, estimated the metabolic rate of three different work tasks from videotapes. Analysis of variance indicated significant ( [Formula: see text] ) differences in the appraisers' recordings of the activities. The appraisers were grouped according to the similarity of the estimated values they gave. The groups thus contained both experienced and inexperienced appraisers, and it was not possible to classify the appraisers into experienced and inexperienced groups according to their earlier experience. The metabolic rates according to the Edholm scale were higher than according to the ISO 7243 table. The differences in metabolic rates given by the individual observers varied from 38 to 118 W/m(2). The variations in the estimation of metabolic rates were greater when the Edholm scale was used. This variation caused considerable variation also in the predicted mean vote, PMV index. It is recommended that the appraisers be selected carefully, because it is not possible to know whether a randomly selected appraiser is an 'average' or an 'extreme' appraiser without a test. Before conducting extensive field surveys where several appraisers estimate the metabolic rates, it would be useful to arrange training in order to calibrate the levels of the Edholm scale as well as ISO method among the appraisers because training clearly unified the estimation.     

Majority gates vs. general weighted threshold gates

In this paper we study small depth circuits that contain threshold gates (with or without weights) and parity gates. All circuits we consider are of polynomial size. We prove several results which complete the work on characterizing possible inclusions between many classes defined by small depth circuits. These results are the following:

Variation in light scattering and water-holding capacity along the porcine Longissimus dorsi muscle

The meat quality of M. longissimus muscle was evaluated in 851 pigs by using the Fibre Optic Probe (FOP) at three sites in the muscle and in both halves of the carcass. A systematic difference between sites was found, with the lowest light scattering (indicating the best meat quality) in the mid-part of the muscle and higher light scattering in the anterior and posterior parts. A non-systematic variation was also observed, with the opposite pattern in some animals, even though it was not frequent. A negative influence of the shackling was found, yielding higher FOP values in the shackled half.

Drip loss measurements in the Longissimus muscle, taken from another 100 pig carcasses, were evaluated using three methods. Drip loss, too, showed a considerable variation along the Longissimus muscle, with minimum losses around the last rib. Repeatability estimates, calculated from two non-consecutive pieces of the Longissimus dorsi muscle from each carcass, varied from 0·4 when keeping samples vacuum packed for 2 days, to 0·5 when the samples were either kept in plain plastic bags for 2 days or in a meat container with a squared inset for 1 or 2 days.     

Crystallization of Fe-Si-B metallic glasses studied by X-ray synchrotron radiation

We have studied the crystallization kinetics of Fe_90-x Si _x B₁₀ amorphous alloys withx ranging from 7 to 21, by synchrotron X-ray radiation. Using energy- dispersive X-ray diffraction, the kinetics of the different crystalline phases evolving during isothermal annealing were followed. These crystalline phases were identified as precipitation of-Fe(Si) and/or Fe₃Si in the amorphous matrix. At a later time or at a higher temperature, Fe₂B starts to crystallize (x < 21 ). Only at low iron concentration (x = 21) was the second phase different, namely Fe₅SiB₂ The hypo- and hyper-eutectic Fe-Si-B glasses were found to crystallize differently. The crystallization processes are discussed in some detail.     

Enthalpies of formation of transition-metal lanthanide laves phases with the MgCu2 structure

Experimental information and theoretical estimates for the enthalpy of formation at 298 K for the RM₂ (whereM = Fe, Co,orNi andR = La, Ce, Pr, Nd, Sm, Gd, Tb, Dy, Ho, Er, Tm, Yb, or Lu) lanthanide Laves phases with the MgCu₂ (C15) structure are reviewed and discussed in the light of information on lattice parameters and atomic volume. The purpose of the present study is to analyze all the available experimental information on enthalpies of formation for transition-metal lanthanide Laves phases and then plot the data in order to reveal tendencies and allow reliable estimates of data that have not yet been measured. It is concluded that as the lanthanide atomic number increases the enthalpy of formation is almost constant or becomes slightly more negative. The accompanying volume contraction is slightly larger than expected from the lanthanide contraction, 7.6 %. From the so-called Gschneidner correlation one would have expected the contrary behavior, that is, that the bonding strength would become slightly lower when going from LaM₂ to LuM₂. An increase in the transition-metal atomic number has a stronger effect on the enthalpy of formation and atomic volume than an increase in the lanthanide atomic number.     

In Vivo Analysis of the Biocompatibility and Bone Healing Capacity of a Novel Bone Grafting Material Combined with Hyaluronic Acid

The present in vivo study analyses both the inflammatory tissue reactions and the bone healing capacity of a newly developed bone substitute material (BSM) based on xenogeneic bone substitute granules combined with hyaluronate (HY) as a water-binding molecule. The results of the hyaluronate containing bone substitute material (BSM) were compared to a control xenogeneic BSM of the same chemical composition and a sham operation group up to 16 weeks post implantationem. A major focus of the study was to analyze the residual hyaluronate and its effects on the material-dependent healing behavior and the inflammatory tissue responses. The study included 63 male Wistar rats using the calvaria implantation model for 2, 8, and 16 weeks post implantationem. Established and Good Laboratory Practice (GLP)-conforming histological, histopathological, and histomorphometrical analysis methods were conducted. The results showed that the new hyaluronate containing BSM was gradually integrated within newly formed bone up to the end of the study that ended in a condition of complete bone defect healing. Thereby, no differences to the healing capacity of the control BSM were found. However, the bone formation in both groups was continuously significantly higher compared to the sham operation group. Additionally, no differences in the (inflammatory) tissue response that was analyzed via qualitative and (semi-) quantitative methods were found. Interestingly, no differences were found between the numbers of pro- and anti-inflammatory macrophages between the three study groups over the entire course of the study. No signs of the HY as a water-binding part of the BSM were histologically detectable at any of the study time points, altogether the results of the present study show that HY allows for an optimal material-associated bone tissue healing comparable to the control xenogeneic BSM. The added HY seems to be degraded within a very short time period of less than 2 weeks so that the remaining BSM granules allow for a gradual osteoconductive bone regeneration. Additionally, no differences between the inflammatory tissue reactions in both material groups and the sham operation group were found. Thus, the new hyaluronate containing xenogeneic BSM and also the control BSM have been shown to be fully biocompatible without any differences regarding bone regeneration.