Electrical properties of (Bi3.5La0.5)Ti3O12 thin-films prepared by liquid source misted chemical deposition

The ((Bi_3.5La_0.5)Ti₃O₁₂(BLT) thin-films used in this study were fabricated on a Pt(111)/SiO₂/Si(100) substrate by a Liquid Source Misted Chemical Deposition (LSMCD) technique. X-ray diffraction patterns showed that the BLT films were crystallized and no other phases were observed when annealed above 650 ‡C. Grain size and remnant polarizations increased with increase in the annealing temperature, while leakage current densities decreased. The remnant polarizations (Pr) increased from 2.0 to 4.8 and 19.0 μC/cm2 with increase in the annealing temperature from 650 to 700 and 750 ‡C, respectively. The BLT films annealed at 700 ‡C in O₂ showed a good fatigue resistance of reduced polarization by 10% after 10⁹ switching cycles when 9 V of bipolar voltage was applied at a frequency of 40 kHz.     

Measurement and modeling solubility of bioactive coumarin and its derivatives in supercritical carbon dioxide

To design a supercritical fluid extraction process for the separation of bioactive substances from natural products, a quantitative knowledge of phase equilibria between target biosolutes and solvent is necessary. How-ever, mostly no such information is available in literature to date. Thus in the present study, illustratively the solubility of bioactive coumarin and its various derivatives (i.e., hydroxy-, methyl-, and methoxy-derivatives) in supercritical CO₂ were measured at 308.15–328.15 K and 10–30 MPa. Also, the pure physical properties such as normal boiling point, critical constants, acentric factor, molar volume and standard vapor pressure for coumarin and its derivatives were estimated. By these estimated information, the measured solubilities were quantitatively correlated by an approximate lattice equation of state proposed recently by the present authors.     

Reynolds number scaling of flow in a Rushton turbine stirred tank. Part I—Mean flow, circular jet and tip vortex scaling

We consider scaling of flow within a stirred tank with increasing Reynolds number. Experimental results obtained from two different tanks of diameter 152.5 and 292.1 mm, with a Rushton turbine operating at a wide range of rotational speeds stirring the fluid, are considered. The Reynolds number ranges from 4000 to about 78,000. Phase-locked stereoscopic PIV measurements on three different vertical planes close to the impeller give phase-averaged mean flow on a cylindrical surface around the impeller. The scaling of θ- and plane-averaged radial, circumferential and axial mean velocity components is first explored. A theoretical model for the impeller-induced flow is used to extract the strength and size of the three dominant elements of the mean flow, namely the circumferential flow, the jet flow and the pairs of tip vortices. The scaling of these parameters with Reynolds number for the two different tanks is then obtained. The plane-averaged mean velocity scales with the blade tip velocity above a Reynolds number of about 15,000. However, parameters associated with the jet and tip vortices do not become Reynolds number independence until Re exceeds about 10⁵. The results for the two tanks exhibit similar Reynolds number dependence, however, a perfect collapse is not observed, suggesting a sensitive dependence of the mean flow to the finer details of the impeller.     

An analysis of muscles from ultrasound image using morphological information of fascia and thoracic vertebra

In this paper, we propose a new fully computerized image analysis method for measuring the thickness of muscles from ultrasound image obtained by muscle endurance test using morphological information of fascia and thoracic vertebra. Firstly, we divide the image into lumbar region and thoracolumbar region by the difference of density in image for measuring the thickness of muscles. In lumbar region, we notice that the intensity of fascia is relatively higher than other parts. Thus, we measure the thickness of muscles surrounding the fascia area. In the process, we apply median filter to candidate fascia areas for extracting candidate muscle layers between fascias. Then, the thickness of muscles we measure is that of the third layer. In thoracolumbar region, we apply region expansion method for classifying the region into subcutaneous fat part and part including thoracic vertebra. Then, we apply counting method and evolutionary computation search model to find the measuring location that is in between subcutaneous fat area and thoracic vertebra. In experiment, the proposed method is effective in measuring the thickness of muscles and avoids failures of previous studies. The performance of this approach is sufficiently comparable to that of medical experts.     

Case-based context ontology construction using fuzzy set theory for personalized service in a smart home environment

To provide context-based personalized services utilizing smart appliances in a smart home environment, we propose a framework for PersonAlized Service disCovery Using FuZZY-based CBR and Context Ontology (PASCUZZY). Basically, the PASCUZZY framework is implemented on case-based context ontology. To generate and manage the case instances on the case-based context ontology, we adopt the fuzzy set theory to transpose numerical-type context data sensed from the surrounding environment. The context is transposed to linguistic-type context instances on the context ontology. In addition, to formalize and manage the context and services as multi-attributed data, the context ontology was developed reflecting the structure of cases borrowed from case-based reasoning. Furthermore, we propose adaptation methods to adjust the generic fuzzy membership functions depending on the inhabitants’ context. It is performed by modifying the values of the membership number and/or modifying the numbers of the linguistic terms that are based on the inhabitants’ context to affect the membership numbers. The adapted membership functions return the personalized degree of memberships depending on the specialized context of a specific fuzzy variable. Inevitably, the number of cases on the case-based context ontology will be increased from time to time. We apply Ward’s method not only to reduce the search effort via a hierarchical clustering on the case-based context ontology but also to find the most similar service as a solution to the new context. To verify the superiority of the PASCUZZY framework, we perform two kinds of evaluations. First, we evaluate the effectiveness of the adaptation of the fuzzy membership functions. Second, we verify the effectiveness of the application of a clustering method to the case instances of the case-based context ontology to identify the most similar service. Results of the experiment verified the effectiveness and superiority of the PASCUZZY framework.     

CO hydrogenation over potassium-promoted Fe/carbon catalysts

The effects of potassium on the catalytic behavior in CO hydrogenation over K-promoted Fe/carbon catalysts having low K/Fe ratios were investigated. Even though the doses of potassium were low the promotional effects were pronounced, especially on the olefin-to-paraffin ratio, and theC ₃ toC ₄ olefin selectivities of the K-promoted catalysts were as high as 51 to 66 mol%. Over the catalysts having no or low potassium content the olefin-to-paraffin ratio and the ratio of the CO₂ formation rate to the rate of CO conversion to hydrocarbons remained roughly the same regardless of temperature, while over the K-promoted catalysts having higher potassium content they increased with temperature. Formation of significant amounts of filamentous carbon was observed in the K-promoted catalysts; however, the carbon deposition did not appear to affect the inherent activity and selectivity of the K-promoted catalysts.     

Synthesis and properties of acrylonitrile-CR-methyl methacrylate graft copolymer

Graft copolymerization of acrylonitrile (AN) and methyl methacrylate (MMA) onto polychloroprene (CR) was carried out using benzoyl peroxide as initiator. The effects of mole ratio of AN to MMA, reaction temperature, reaction time, solvent, and initiator concentration on the graft copolymerization were examined. It was found that the thermal stability and weatherability of the AN—CR—MMA graft copolymer (ACM) were considerably better than those of CR.     

Adhesion property of novel polyimides with 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride

Novel polyimides were synthesized from 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride (6FPPMDA) by a conventional two‐step process: the preparation of poly(amic acid) followed by solution imidization via refluxing in p‐chlorophenol. The diamines used for polyimide synthesis included bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide, bis(3‐aminophenyl)‐4‐trifluoromethylphenyl phosphine oxide, and bis(3‐aminophenyl)phenyl phosphine oxide. The synthesized polyimides were designed to have a molecular weight of 20,000 g/mol by off‐stoichiometry and were characterized by Fourier transform infrared, NMR, differential scanning calorimetry, and thermogravimetric analysis. In addition, their intrinsic viscosity, solubility, water absorption, and coefficient of thermal expansion (CTE) were also measured. The adhesion properties of the polyimides were evaluated via a T‐peel test with bare and silane/Cr‐coated Cu foils, and the failure surfaces were investigated with scanning electron microscopy. The 6FPPMDA‐based polyimides exhibited high glass‐transition temperatures (280–299°C), good thermal stability (>530°C in air), low water absorption (1.46–2.16 wt %), and fairly low CTEs (32–40 ppm/°C), in addition to good adhesion properties (83–88 g/mm) with silane/Cr‐coated Cu foils. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1801–1809, 2005     

Electrochemical studies of pyrite oxidation and reduction using freshly-fractured electrodes and rotating ring-disc electrodes

Oxidation and reduction processes on coal- and mineral-pyrite surfaces have been investigated to better understand the reactions that control the hydrophobicity and flotation behavior of pyrite. The incipient oxidation and reduction reactions were studied using fresh surfaces of pyrite that were created by in situ fracturing electrodes potentiostated at a predetermined potential. Chronoamperometry immediately after fracture and subsequent cyclic voltammetry have established that fresh fracture surfaces of pyrite instantaneously assume a unique potential (referred to as the “stable” potential) at which neither oxidation nor reduction takes place. For Peruvian and Chinese pyrites, the stable potential is −0.28 V (standard hydrogen electrode, SHE) at pH 9.2 and 0 V at pH 4.6. The initial oxidation of pyrite begins at potentials slightly positive of the stable potential and is believed to produce a hydrophobic sulfur-rich species, most likely a polysulfide or metal-deficient sulfide. A rotating ring-disc electrode (RRDE) was employed to study the kinetics and mechanisms of surface reactions on pyrite over moderate potential ranges. Two distinct soluble reduction products (ferrous hydroxide and HS⁻) and one distinct soluble oxidation product (ferrous hydroxide) were observed on pyrite in alkaline solutions. It is concluded that the initial oxidation of pyrite and the oxidation of ferrous to ferric hydroxide occur in a similar potential range. When the electrode is oxidized, e.g. by polishing, prior to experiments, the initial oxidation of pyrite is masked by the oxidation of ferrous hydroxide, making it difficult to study the oxidation of pyrite itself.     

Syntheses of new black dyes for ink-jet inks

Drop-on-demand ink-jet inks made from dyes generally show poor light and wet fastness. A number of studies have been carried out previously to improve the fastness of such inks by introducing novel dyes and new additives. Based on the research results, use of fast dyes could give ink-jet inks with good properties. This study describes new black dyes for aqueous ink-jet inks, which show better light and wet fastness and print quality, compared to an analogous ink formulated from CI Food Black 2.