Effect of processing method on microstructure,electrical conductivity and electromagnetic wave interference (EMI) shielding performance of carbon nanofiber filled thermoplastic polyurethane composites

In this study, effect of processing method on microstructure formation and related electrical conductivity and electromagnetic interference shielding effectiveness of carbon nanofiber (CNF) filled thermoplastic polyurethane (TPU) composites, prepared via three different processing techniques; (i) melt compounding (MC) in a twin screw extruder, (ii) simple solution mixing (SM) on a magnetic stirrer, and (iii) solution mixing with sonication (SM-U) were investigated. It was found that the electrical conductivity values of samples decreased in the order of SM > SM-U > MC for a particular amount of CNF. The electromagnetic test results showed that the samples prepared with SM and SM-U methods yielded higher total shielding effectiveness (SE_T) values than those prepared with MC. SE_T values of samples including of 20 phr of CNF prepared with MC, SM-U and SM methods were varied in the range of 10–30 dB, 20–60 dB and 20–80 dB, respectively within a frequency range of 1–12 GHz.     

The interleukin-10 promoter genotype predicts diastolic dysfunction in maintenance hemodialysis patients

Interleukin-10 (IL-10) predominantly acts as an anti-inflammatory factor. Polymorphisms in the IL-10 gene promoter determine quantitative cytokine production. Doppler echocardiography and tissue Doppler imaging (TDI) are superior to conventional echocardiography to evaluate diastolic dysfunction. The IL-10 gene promoter polymorphism at position (-1082) was studied for its association with conventional and Doppler echocardiographic and TDI parameters in 112 hemodialysis (HD) patients. Blood pressure, serum C-reactive protein (CRP), and albumin levels were also examined for the association study. The genetic association study showed that among the HD patients, there was no difference in the prevalence of systolic and diastolic dysfunction between genotypes on conventional echocardiography. However, using Doppler echocardiography and TDI, high producers for the IL-10 -1082 promoter (-1082/GG) have higher E velocities, E/A values, lateral, and septal E' velocities and a lower isovolumic ventricular relaxation time than low (-1082/AA) and intermediate producers (-1082/GA). Significantly higher levels of serum CRP levels and lower plasma albumin levels were found in low and intermediate producers for the IL-10 -1082 promoter than high producers. The IL-10 genotype may balance the effects of inflammatory cytokines on the myocardium and may be a determinant of LV function in HD patients.     

Dendrimer–Palladium Complex Catalyzed Oxidation of Terminal Alkenes to Methyl Ketones

Silica‐supported polyamidoamine (PAMAM) dendrimers with different spacer lengths were prepared. After the introduction of diphenylphosphino groups, complexation to dibenzylidenepalladium(0) gave the desired silica‐supported dendrimer–palladium catalyst complexes G0 to G4‐C2‐Pd. These catalysts showed activity towards the oxidation of terminal alkenes to methyl ketones. A dependence of catalytic activity on the spacer length of the diamine in PAMAM was observed.     

Lp norm approaches for estimating voltage flicker

It is important to accurately estimate instantaneous voltage flicker magnitudes and frequencies in order to correctly evaluate voltage fluctuations. Voltage flicker is a problem in electric power quality. Different approaches used to determine the magnitude of the voltage flicker have been presented: measurement methods generally use a flickermeter device. Simulation methods require a computer model of the disturbing load and the flickermeter. Calculation methods necessitate a simplified empirical formula. Estimation algorithms are based on the estimation of the voltage flicker components. In this paper, two models of voltage flicker are discussed: L_p estimation algorithms utilizing L₁, L₂ and L_∞ norms are used to estimate the voltage magnitudes of the flicker signals as well as the fundamental voltage magnitude. The main result is that it is possible to design an L_p estimator to identify flicker frequency and amplitude from time series measurements.     

Bending strength of piezoelectric ceramics and single crystals for multifunctional load-bearing applications

The topic of multifunctional material systems using active or smart materials has recently gained attention in the research community. Multifunctional piezoelectric systems present the ability to combine multiple functions into a single active piezoelectric element, namely, combining sensing, actuation, or energy conversion ability with load-bearing capacity. Quantification of the bending strength of various piezoelectric materials is, therefore, critical in the development of load-bearing piezoelectric systems. Three-point bend tests are carried out on a variety of piezoelectric ceramics including soft monolithic piezoceramics (PZT-5A and PZT-5H), hard monolithic ceramics (PZT-4 and PZT-8), single-crystal piezoelectrics (PMN-PT and PMN-PZT), and commercially packaged composite devices (which contain active PZT-5A layers). A common 3-point bend test procedure is used throughout the experimental tests. The bending strengths of these materials are found using Euler-Bernoulli beam theory to be 44.9 MPa for PMN-PZT, 60.6 MPa for PMN-PT, 114.8 MPa for PZT- 5H, 123.2 MPa for PZT-4, 127.5 MPa for PZT-8, 140.4 MPa for PZT-5A, and 186.6 MPa for the commercial composite. The high strength of the commercial configuration is a result of the composite structure that allows for shear stresses on the surfaces of the piezoelectric layers, whereas the low strength of the single-crystal materials is due to their unique crystal structure, which allows for rapid propagation of cracks initiating at flaw sites. The experimental bending strength results reported, which are linear estimates without nonlinear ferroelastic considerations, are intended for use in the design of multifunctional piezoelectric systems in which the active device is subjected to bending loads.     

Co-Fe films: effect of Fe content on their properties

The characterizations of Co-Fe films electrodeposited on Ti substrates under potentiostatic conditions were investigated as a function of the Fe content in the films. The compositional analysis was carried out by energy dispersive X-ray spectroscopy. Scanning electron microscopy used to analyze the surface morphology of the films revealed that the film surface became rather smooth with the increase of the Fe contents. X-ray diffraction patterns showed that the crystal structure changed depending on the Co:Fe ratio in the films. It was observed that the crystal structure converted from the predominant face-centered-cubic to the body-centered-cubic with increasing Fe content. All films showed anisotropic magnetic resistance, but their magnitudes decrease as the Fe content increases. Magnetic data obtained from by vibrating sample magnetometer revealed that the changes observed in the saturation magnetization and coercivity values may arise from the Fe content of the films. The different magnetic and magnetotransport properties may come from the structural differences caused by the Fe content.     

The effect of Fe content in electrodeposited CoFe/Cu multilayers on structural, magnetic and magnetoresistance characterizations

A series of CoFe/Cu multilayers were electrodeposited on Ti substrates from the electrolytes containing their metal ion under potentiostatic control, but the Fe concentration in the electrolytes was changed from 0.0125 M to 0.2 M. The deposition was carried out in a three-electrode cell at room temperature. The deposition of Cu layers was made at a cathode potential of -0.3 V with respect to saturated calomel electrode (SCE), while the ferromagnetic CoFe layers were deposited at -1.5 V versus SCE. The structural studies by X-ray diffraction revealed that the multilayers have face-centered-cubic structure. The magnetic characteristics of the films were investigated using a vibrating sample magnetometer and their easy-axis was found to be in film plane. Magnetoresistance measurements were carried out using the Van der Pauw method at room temperature with magnetic fields up to +/- 12 kOe. All multilayers exhibited giant magnetoresistance (GMR) and the GMR values up to 8% were obtained.     

Towards full-structure determination of bimetallic nanoparticles with an aberration-corrected electron microscope

To fully understand the properties of functional nanostructures such as catalytic nanoclusters, it is necessary to know the positions of all the atoms in the nanostructure. The catalytic properties of metal nanoclusters can often be improved by the addition of a second metal, but little is known about the role of the different metals in these bimetallic catalysts, or about their interactions with each other and the support material. Here we show that aberration-corrected scanning transmission electron microscopy of supported rhodium-iridium clusters, combined with dynamic multislice image simulations, can identify individual atoms, map the full structure, and determine changes in the positions of metal atoms in sequential images. This approach could help in the development of new and improved catalysts and other functional nanostructures.     

Subjective wear trials to evaluate thermal comfort of the foot clothing system including a sweat pad

Subjective wear trials were conducted to evaluate effects of disposable antibacterial sweat pads on foot thermal comfort. Sweat pads were produced with polypropylene and polylactic acid nonwoven topsheet layers which were treated with different herbal antibacterial materials. Trials were carried out with 10 male subjects under 10 °C and 50% relative humidity simulating sweating during a moderate activity in cold environments. Besides microclimate temperature and relative humidity measurements, subjective thermal (coolness, dampness, and comfort) and other sensations (stickiness, slippiness, etc.) were obtained by five point rating scales. Bending rigidity, friction coefficients, and moisture management properties of the topsheet fabrics and pads were tested. Results show that foot sweat pads enabled drier microclimate, warmer sensations, and higher comfort evaluations. Antibacterial treatments did not affect bending rigidity values of the nonwoven topsheet fabrics, but some applications decreased spreading speed, increased roughness of the pad surfaces, and wetting time values which are not preferable.     

Differences observed in properties of ternary NiCoFe films electrodeposited at low and high pH

Ternary NiCoFe films were potentiostatically electrodeposited from the electrolytes with low (3.0) and high (3.6) pH levels, and differences in their compositional, structural, magnetic and magnetoresistance properties were studied. The compositional analysis demonstrated that the Ni content in the films decreased, and Co and Fe content increased while electrolyte pH was changed from low to high level. The structural analysis of the films was carried out using the X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The XRD data revealed that the films have a strong (111) texture of the face-centred cubic (fcc) structure at low pH, while for the films at high pH a mixture of dominantly fcc and hexagonal closed packed structure was observed. The SEM studies showed that films grown at low pH level had comparatively larger grains than those at high pH. The magnetic characteristics studied by a vibrating sample magnetometer and magnetotransport properties were seen to be changed by the electrolyte pH. However, all films have in-plane magnetic anisotropy. The differences observed in the magnetic and magnetotransport properties were attributed to the microstructural changes caused by the electrolyte pH.