Effect of phonon scattering from neutral and charged impurity centers on the lattice heat conductivity of PbTe:(Tl, Na)

Experimental data on the effect of thallium and sodium impurities on the lattice heat conductivity of PbTe at room temperature are reported. Because the lattice of lead chalcogenides is strongly polarized near charged impurities, the effect of impurities on the lattice heat conductivity depends substantially on their charge state. This property of the material has been used to determine the charge state of the thallium impurity in PbTe. The results obtained argue for a model of quasi-local thallium-impurity states which assumes low electron-correlation energy at an impurity center. Fiz. Tverd. Tela (St. Petersburg) 40, 1206–1208 (July 1998)     

Interactions between the components in isotactic polypropylene blended with EPDM

The interaction of isotactic polypropylene with ethylene propylene diene terpolymer in their blends has been investigated by use of differential scanning calorimetry, dynamic mechanical analysis, wide- and small-angle x-ray scattering, and by investigating the nucleation and kinetics of crystallization of the iPP component under the polarization microscope. It is found, that the dispersion of the EPDM component in the iPP matrix is dependent on blend composition and is maximal at 10% EPDM content. An interface layer between the two components is formed by migration of iPP molecules into the EPDM phase. A model for this interface is proposed.     

Thoms Effect as Influenced by the Concentration and Molecular Parameters of the Cationic Copolymer of Acrylamide

The Thoms effect observed with water-soluble cationic copolymer of acrylamide was studied in relation to the concentration, molecular weight, and molecular weight polydispersity of the polymeric additive, with its composition and composition polydispersity being constant.     

Alloying by high dose ion implantation of iron into magnesium and aluminium

Alloys of the systems Fe–Al (mixable over the whole concentration range) and Fe–Mg (insoluble with each other) were produced by implantation of Fe ions into Al and Mg, respectively. The implantation energy was 200 keV and the ion doses ranged from 1 × 10₁₄ to 9 × 10₁₇cm^-2The obtained implantation profiles were determined by Auger electron spectroscopy depth profiling. Maximum iron concentrations reached were up to 60 at.% for implantation into Al and 94 at.% for implantation into Mg. Phase analysis of the implanted layers was performed by conversion electron Mössbauer spectroscopy and X‐ray diffraction. For implantation into Mg, two different kinds of Mössbauer spectra were obtained: at low doses paramagnetic doublets indicating at least two different iron sites and at high doses a dominant ferromagnetic six‐line‐pattern with a small paramagnetic fraction. The X‐ray diffraction pattern concluded that in the latter case a dilated αiron lattice is formed. For implantation into Al, the Mössbauer spectra were doublet structures very similar to those obtained at amorphous Fe–Al alloys produced by rapid quenching methods. They also indicated at least two different main iron environments. For the highest implanted sample a ferromagnetic six‐line‐pattern with magnetic field values close to those of Fe₃Al appeared.     

Evolved gas analysis (EGA) of brick clays

Using a system based on non-dispersive infrared (NDIR) detectors, evolved gas analysis (EGA) was able to identify and quantify the principal volatiles produced by heating powdered samples of UK brick clays. From these results, atmospheric emissions likely to result from brick production can be predicted. In addition, EGA results for extruded brick clay test pieces are significantly different from those of powdered samples. Within an extruded brick clay body, evolved gases are contained within a pore system and evolved gas-solid phase reactions also occur. This EGA study provides further evidence on the nature of firing reactions within brick clay bodies. The qualitative and quantitative influence of heating rate — a key process condition in brick manufacture — on gas release is also outlined.Dedicated to Dr. Robert Mackenzie on the occasion of his 75th birthday