Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Effect of vibration condition and inter-particle frictions on the packing of uniform spheres

We present a numerical study of the packing of uniform spheres under three-dimensional vibration using the discrete element method (DEM), focusing on the effects of vibration condition (amplitude and frequency) and inter-particle frictions (sliding and rolling frictions). The results are analysed in terms of packing density, coordination number (CN), radial distribution function (RDF) and pore structure. It is shown that increasing either the vibration amplitude or frequency causes packing density to increase initially to a maximum and then decrease. Both vibration frequency and amplitude should be considered to characterize the effect of vibration process on packing structure. The sliding and rolling frictions between particles can decrease packing density since they dissipate energy, although the effect of rolling friction is less significant. In line with the change of packing density, microstructural properties such as CN, RDF and pore distribution also change: a looser packing often corresponds to smaller CN, less peaked RDF and larger but more widely distributed pores.     

MSP-G320240DBCW-211N大规模点阵式LCD与PIC单片机接口技术

介绍了大规模点阵式液晶显示器MSP-G320240DBCW-211N的特点及其与PIC18F6620单片机的接口技术，提出了应用过程中可能遇到的问题和解决方法．给出相关的C程序设计并在研制的智能光电检测仪器上得以成功地应用。     

Application of Support Vector Machines in Assessing Conceptual Cost Estimates

Total conceptual cost estimates and the assessment of the quality of these estimates are critical in the early stages of a building construction project. In this study, the support vector machine (SVM) model for assessing the quality of conceptual cost estimates is proposed, and the application of SVM in construction areas is investigated. The results show that the SVM model assessed the quality of conceptual cost estimates slightly more accurately than the discriminant analysis model. This shows that using the SVM has potential in construction areas. In addition, the SVM model can assist clients in their evaluation of the quality of the estimated cost and the probability of exceeding the target cost, and in their decision on whether or not it is necessary to seek a more accurate estimate in the early stages of a project.     

钻井液固相化学清洁剂ZSC-201的合成及性能

介绍了钻井液用固相化学清洁剂ZSC－201的室内合成及性能评价，结果表明，固相化学清洁剂ZSC－201具有较强的抑制性，可有效抑制粘土水化分散，保证钻井液清洁，在钻井液体系中与阴、阳离子型钻井液处理剂配伍性好，同时具有较好的抑制增效作用，在有效的加量内对钻井液滤矢量和流变性等影响小，固相化学清洁剂ZSC－201已在中原油田近30口井中应用，具有良好的推广应用前景。     

Control of calcium hexaluminate grain morphology in in-situ toughened ceramic composites

The influence of processing conditions on the morphology of calcium hexaluminate (CA₆) grains in Al₂O₃: 30 vol% CaO·6Al₂O₃ (CA₆) ceramic composites was investigated. Specimens were prepared by in-situ reaction sintering using precursor powders of alumina, and either calcium carbonate or calcium oxide. In some samples, 1 vol% anorthite glass was added as a sintering aid. X-ray diffraction was used to study the phase development in the as-calcined and sintered states. The resultant microstructures were characterized using both scanning electron microscopy (SEM), and imaging secondary ion mass spectrometry (SIMS). It was found that the CA₆ grains developed a platelike morphology when CaCO₃ was used as the starting calcium-rich powder. In contrast, samples prepared using CaO resulted in equiaxed CA₆ grains. This result was observed to be independent of the anorthite glass addition. The findings are rationalized in terms of distinct CA₆ reaction mechanisms, resulting from differences in the reactivity of the powders during the early stages of calcining.Cement Nomenclature C CaO - A Al₂O₃     

混酸PEG酯的合成及性能研究

用从大豆油脚水解制得的脂肪酸合成混酸聚乙二醇酯，通过测定酸值的方法确定了最佳反应时间为16h。与油酸聚乙二醇酯相比，混酸聚乙二醇酯具有更优良的乳化性、润湿性，可以替代油酸聚乙二醇酯用于纺织、农药和化妆品工业中。     

铸铁热分析用试样新型激冷剂的实验研究

从冷却曲线上相变段倾角最小原则出发，研究了新型激冷剂的配比与热分析法检测铸铁成分精度的关系，实验结果表明，能使相变段倾角最小的成分配比，也能提高对铸铁成分的热分析和检测精度。     

片状陶瓷材料高低温电性能参数的自动检测

由进口电性能仪配上自制的高温系统，计算机自动采集数据，配置成一套高低温电性参数测定装置，该装置的特点是，升温快，炉体小巧，炉芯可更换盛液氮装置，屏蔽良好，等温区长，温工及参数测量精确可靠。     

海底沉积物中天然气水合物生成和分解规律研究进展

对国内外有关海底沉积物中天然气水合物生成和分解规律方面的研究进行了详细调研,得到如下结论:天然气水合物的生成和分解条件在海底沉积物中与在井筒、管道中有明显不同,其主要原因是多孔介质中流体与孔隙壁面间的界面效应对海底沉积物中天然气水合物的形成条件会产生明显影响;在海底沉积物中天然气水合物生成和分解条件的数值模拟技术研究方面,研究者大都假设以天然气水合物作为盖层的成藏类型,借助常规油气藏数值模拟技术进行模拟研究;影响海底沉积物中天然气水合物生成和分解条件的因素很多,因此海底沉积物中天然气水合物生成和分解规律研究必须借助试验模拟、数值模拟和现场测试相结合的综合方式进行。该调研成果可为今后天然气水合物经济有效开采技术方案选择和进行天然气水合物危害控制等提供参考。