全文获取类型
收费全文 | 6252篇 |
免费 | 391篇 |
国内免费 | 320篇 |
学科分类
工业技术 | 6963篇 |
出版年
2024年 | 64篇 |
2023年 | 196篇 |
2022年 | 216篇 |
2021年 | 188篇 |
2020年 | 196篇 |
2019年 | 230篇 |
2018年 | 219篇 |
2017年 | 105篇 |
2016年 | 129篇 |
2015年 | 162篇 |
2014年 | 368篇 |
2013年 | 299篇 |
2012年 | 337篇 |
2011年 | 401篇 |
2010年 | 368篇 |
2009年 | 353篇 |
2008年 | 318篇 |
2007年 | 317篇 |
2006年 | 335篇 |
2005年 | 251篇 |
2004年 | 226篇 |
2003年 | 214篇 |
2002年 | 155篇 |
2001年 | 174篇 |
2000年 | 139篇 |
1999年 | 113篇 |
1998年 | 76篇 |
1997年 | 88篇 |
1996年 | 84篇 |
1995年 | 96篇 |
1994年 | 91篇 |
1993年 | 54篇 |
1992年 | 54篇 |
1991年 | 61篇 |
1990年 | 58篇 |
1989年 | 50篇 |
1988年 | 21篇 |
1987年 | 21篇 |
1986年 | 24篇 |
1985年 | 16篇 |
1984年 | 18篇 |
1983年 | 10篇 |
1982年 | 15篇 |
1981年 | 17篇 |
1980年 | 11篇 |
1979年 | 9篇 |
1978年 | 4篇 |
1959年 | 2篇 |
1955年 | 3篇 |
1951年 | 1篇 |
排序方式: 共有6963条查询结果,搜索用时 15 毫秒
101.
102.
过共晶高硅铸造铝合金磷-稀土双重变质处理 总被引:10,自引:2,他引:10
采用正交实验方法研究了磷、混合稀土变质剂添加量和变质处理温度对Al-22Si-2cu-0.9Mg-1.0Ni过共晶高硅铸造铝合金变质效果的影响。结果表明:磷、稀土的添加量和磷变质处理温度对合金的变质效果起决定作用;稀土添加量对合金室温抗拉强度无明显影响,但能显著提高其高温强度;合金变质处理的最佳工艺如下:磷添加量为0.1%,稀土添加量为0.6%,磷变质温度为830℃,稀土变质温度为810℃。 相似文献
103.
The high cycle fatigue properties and fracture behavior of 2124-T851 aluminum alloy were investigated roundly, including the fatigue crack growth rate, fracture toughness and fatigue S--N curve. Furthermore, the fatigue crack growth rate was analyzed by fitting the curves. And the microstructure of the alloy was studied using by optical microscopy, transmission electron microscopy and X-ray diffractometry, scanning electron microscop1/2 The results show that the fatigue strength and the fracture toughness of 2124-T851 thick plate are 243 MPa and 29.6 MPa.m at room temperature and R=0. 1, respectively. At high cycle fatigue condition, the characteristics of fatigue facture were observed obviously. And the higher the stress amplitude, the wider the space between the fatigue striations, the faster the rate of fatigue crack developing and going into the intermittent fracture area and the greater the ratio between the intermittent fracture area and the whole fracture area. 相似文献
104.
In-plane anisotropy of 1545 aluminum alloy sheet 总被引:3,自引:0,他引:3
1 INTRODUCTIONThe in plane anisotropy of mechanical proper ties brings the limitation to the use of alloy sheet.At the same time, during the material processing,the difficulties of contour machining will also be in creased. For this reason, when designing high performance aluminum alloy sheets, the in planeanisotropy is an important performance parameterthat must be considered. Studies have shown thatminor Sc and Zr in the Al Mg Mn alloy can refinegrains of cast ingot, inhib… 相似文献
105.
106.
107.
108.
本文采用声发射能量技术研究低强度、高塑性材料α-Ti的形变、断裂特征。发现声发射总能量ΣE与长程应力场σ-σs间存在lgΣE-lg(σ-σs)的线性关系,曲线的拐点即为开裂点。因而有可能利用这种方法较精确地测定出低强度、高塑性材料的开裂点,为这类材料的断裂力学测试解决了一个难题。 α-Ti的形变、断裂过程中存在两种声发射源:位错运动引起的滑移和裂纹的徽开裂和长大。 相似文献
109.
采用氧乙炔喷焊工艺,以Ni60自熔合金粉末为喷焊材料,解决了锅炉膜式水冷壁局部严重磨损问题,现场检测和实践证明该工艺是可行的,经济的。 相似文献
110.
采用力学性能测试、扫描电子显微分析、透射电子显微分析和切削性能试验,研究了固溶-冷拉处理的含铅2011合金与Sn、Bi微合金化的新型无铅易切削Al-Cu合金棒材的组织和性能。结果表明:Sn、Bi微合金化的无铅易切削Al-Cu合金的力学性能比传统2011合金的略好;Sn能加快Al-Cu合金的人工时效,细化CuAl2相;与含铅2011合金相比,无铅易切削Al-Cu合金中低熔点相的尺寸分布更均匀,经切削加工后,切屑尺寸更细,表面光洁度更高,具有更好的切削性能。 相似文献