Effects of cubic BN addition and phase transformation on hardness of Al2O3-cubic BN composites

The Vickers hardness of dense Al₂O₃-cubic BN (cBN) composites prepared by spark plasma sintering under a moderate pressure of 100 MPa at 1200-1600 °C was investigated at indentation loads of 0.098-19.6 N. The BN grains in the Al₂O₃-BN composite prepared at 1300 °C showed no transformation from the cBN to hBN phase, and the hardness was 59 GPa at 0.098 N. The hardness of the Al₂O₃ matrix in the Al₂O₃-BN composites containing 10-30 vol% cBN prepared at 1300-1400 °C was around 25 GPa at 0.098 N, which was higher than monolithic Al₂O₃ bodies prepared at the same temperatures. The hardness of the Al₂O₃ matrix in the Al₂O₃-BN composites decreased with increasing sintering temperature. The increase in the hardness of the Al₂O₃ matrix may be due to the decrease in the size of Al₂O₃ grains in the Al₂O₃-BN composites owing to the addition of cBN particles and the decrease in sintering temperature. The Meyer exponents of the monolithic Al₂O₃ bodies and Al₂O₃-BN composites were 1.90-1.94 independent of cBN content.     

Lead(II)‐ion removal by ethylenediaminetetraacetic acid ligand functionalized magnetic chitosan–aluminum oxide–iron oxide nanoadsorbents and microadsorbents: Equilibrium,kinetics, and thermodynamics

Novel nanosized and microsized chitosan–Al₂O₃–Fe₃O₄ (CANF and CAMF, respectively) adsorbents were functionalized with ethylenediaminetetraacetic acid (EDTA) ligands and applied to the removal of Pb(II) ions. The prepared adsorbents were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and Brunauer–Emmett–Teller analysis, and their adsorption potentials were investigated with Pb(II) as a target metal under various experimental conditions. Our results show that the EDTA functionalization of CANF and CAMF increased their adsorption capacities about 31.5 and 38 times, respectively. The optimum dosage obtained was 1.0 g/L for both EDTA‐functionalized adsorbents, and the maximum adsorption took place at pH = 5.3. The kinetic results revealed that the adsorption obeyed the pseudo‐second‐order model and that the pore diffusion process played a key role in the adsorption kinetics. Also, the results of equilibrium isotherms indicate the good fit of the experimental data by the Langmuir isotherm model under the studied concentration and temperature ranges, and the adsorptions of Pb(II) ions from aqueous solution followed the monolayer coverage of the adsorbents. The maximum Pb(II)‐ion adsorption capacities of EDTA–CANF and EDTA–CAMF were 160 and 157 mg/g, respectively. These metal‐loaded adsorbents could be readily recovered from aqueous solution by magnetic separation and reused. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44360.     

Textile‐surface interfacial asymmetric polymerization

This research demonstrated that polymerization of aniline on cellulose produces chiroptically active composites. Polymerization of aniline in the presence of cotton fibers consisting of chiral cellulose are performed to prepare a polyaniline (PANI)/cotton composite. The polymerization is conducted at the cotton interface. The resultant PANI/cotton composite shows chiroptical activity elucidated with diffuse reflectance circular dichroism. In this reaction, textile‐surface interfacial asymmetric polymerization is performed with imprinting of chiral structure from the cotton as a natural chiroptically active polymer to the PANI. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41118.     

Chemical Synthesis of a Synthetic Analogue of the Sialic Acid‐Binding Lectin Siglec‐7

As a basis for the development of an artificial carbohydrate‐binding lectin, we chemically synthesized a domain of siglec‐7, a well‐characterized sialic‐acid‐binding lectin. The full polypeptide (127 amino acids) was constructed by sequential native chemical ligation (NCL) of five peptide segments. Because of poor cysteine availability for NCL, cysteine residues were introduced at suitable ligation sites; these cysteine residues were alkylated in order to mimic native glutamine or asparagine residues, or converted to an alanine residue by desulfurization after NCL. After folding the full‐length polypeptide, the sialic‐acid‐binding activity of the synthetic siglec‐7 was clearly demonstrated by STD NMR and ELISA experiments. We succeeded in the synthesis of siglec‐7 by installing three extra cysteine residues with side‐chain modifications and found that these modifications did not affect the binding activity.     

Preparation of (110)-oriented SrTiO3 film on quartz glass by laser chemical vapor deposition

SrTiO₃ (STO) film was prepared on quartz glass by laser chemical vapor deposition at a deposition temperature (T_dep) ranged from 760 to 1104 K. Effect of the T_dep on the orientation, crystallinity, texture, and microstructure of the STO film was investigated. As the T_dep was increased, the preferred orientation of the STO film tended to be (110)-orientated with corresponding texture coefficient (TC) on the (110) reflection enhanced from 2.3 to 6; meanwhile, the full width at half maximum of the ω-scan on the (110) reflection decreased from 0.85° to 0.59°. The (110)-oriented grains were in wedge shape about 60 × 150 nm in size, which tended to be flat at an elevated T_dep of 1104 K.     

Heteroepitaxial growth of thick 3C-SiC (110) films by Laser CVD

Previously, we found 3C-SiC films favor to grow in <111> orientation on Si (110) ( https://doi.org/10.1111/jace.15260 ). However, epitaxial growth of thick <110>-3C-SiC is still a big challenge. In this study, thick 3C-SiC (110) epitaxial films were prepared on Si (110) substrate by laser chemical vapor deposition (LCVD) using hexamethyldisilane (HMDS) in H₂ atmosphere. The investigation of growth mechanism showed that the laser of LCVD played an important role during the depositions. Observation by high-resolution transmission electron microscopy (HRTEM) revealed that the interface of 3C-SiC (110)/Si (110) exhibited rough texture at atomic level. The atomic roughness on Si (110) surface could be a key factor for 3C-SiC (110) nucleation. The growth of thick 3C-SiC (110) epitaxial films could be very promising for new development in power electronics applications.     

Positive-temperature-coefficient effect of electrical resistivity below melting point of poly(vinylidene fluoride) (PVDF) in Ni particle-dispersed PVDF composites

This paper discusses the positive-temperature-coefficient effects of resistivity in Ni particle-dispersed poly(vinylidene fluoride) (PVDF) composites based on experiment results from SEM, DSC, and pressure-volume-temperature (PVT) measurements. The melting points of composites with Ni content of 20, 30, 40, and 50vol.% were equal to that of pure PVDF. The PTC effects in composites with Ni content of 40 and 50vol.% occurred at temperatures near the melting point of the PVDF matrix, whereas those in composites with Ni content of 20 and 30vol.% occurred at temperatures below the melting point of the PVDF matrix. We found that the PTC effect occurs even without melting of the matrix polymer. Moreover, we determined that a slight increase in specific volume at temperatures below the melting point of the matrix polymer acts fully as a driving force for forming a gap between fillers. This suggestion was backed up by theoretical analyses using percolation theory and a thermal-fluctuation-induced tunneling model.     

NAD+‐Dependent Dehydrogenase PctP and Pyridoxal 5′‐Phosphate Dependent Aminotransferase PctC Catalyze the First Postglycosylation Modification of the Sugar Intermediate in Pactamycin Biosynthesis

The unique five‐membered aminocyclitol core of the antitumor antibiotic pactamycin originates from d ‐glucose, so unprecedented enzymatic modifications of the sugar intermediate are involved in the biosynthesis. However, the order of the modification reactions remains elusive. Herein, we examined the timing of introduction of an amino group into certain sugar‐derived intermediates by using recombinant enzymes that were encoded in the pactamycin biosynthesis gene cluster. We found that the NAD⁺‐dependent alcohol dehydrogenase PctP and pyridoxal 5′‐phosphate dependent aminotransferase PctC converted N‐acetyl‐d ‐glucosaminyl‐3‐aminoacetophonone into 3′‐amino‐3′‐deoxy‐N‐acetyl‐d ‐glucosaminyl‐3‐aminoacetophenone. Further, N‐acetyl‐d ‐glucosaminyl‐3‐aminophenyl‐β‐oxopropanoic acid ethyl ester was converted into the corresponding 3′‐amino derivative. However, PctP did not oxidize most of the tested d ‐glucose derivatives, including UDP‐GlcNAc. Thus, modification of the GlcNAc moiety in pactamycin biosynthesis appears to occur after the glycosylation of aniline derivatives.     

Syntheses of group 4 transition metal complexes bearing 2-pyridinethiolate ligands and their catalytic activities for ethylene polymerization

Titanium bis(2-pyridinethiolate) complexes, Ti(6-R-SPy)₂(NMe₂)₂ (6-R-SPy = 6-R-2-pyridinethiolate, 3a: R = H; 3b: R = Me; 3c: R = Ph; 3d: R = C₆H₄-4-Me; 3e: R = C₆H₄-4-t-Bu; 3f: R = C₆H₃-3,5-Me₂), and the titanium bis(2-pyridinolate) complexes, Ti(6-Ph-OPy)₂(NMe₂)₂ (6-Ph-OPy = 6-phenyl-2-pyridinolate, 8) were prepared by treating Ti(NMe₂)₄ with 2 equiv. of 6-R-2-pyridinethiol or 6-Ph-2-pyridinol. The cis-configuration of the diamido moieties in the pseudo octahedral geometry was elucidated by X-ray crystallography for 3a. Reaction of M(NMe₂)₄ (M = Ti, Zr) with 4 equiv. of 2-pyridinethiol cleanly gave tetrakis(pyridinethiolate) complexes, M(6-H-SPy)₄·THF (6: M = Ti; 7: M = Zr). The triangular dodecahedral geometries of 6 and 7 were also revealed by X-ray crystallography. These complexes catalyzed ethylene polymerization upon activation with MAO (methylaluminoxane) or MMAO (modified MAO). The catalytic activities of titanium bis(6-aryl-pyridinethiolate) systems were found to be remarkably higher than that of titanium bis(6-methyl-pyridinethiolate) system. Among the complexes synthesized in this study, Ti[6-(C₆H₃-3,5-Me₂)-SPy]₂(NMe₂)₂ (3f)/MMAO showed the highest activity (1200 kg/Ti-mol h atm) for ethylene polymerization at 60 °C under atmospheric pressure. In contrast, the activity of the corresponding 6-aryl-pyridinolate system 8/MMAO was rather low (9.3 kg/Ti-mol h atm). Both the N-S chelating structure and the bulky aryl substituents are essential for the high activities of the 6-aryl-pyridinethiolate complexes.     

What Types of Defects Are Really Discovered in Code Reviews?

Research on code reviews has often focused on defect counts instead of defect types, which offers an imperfect view of code review benefits. In this paper, we classified the defects of nine industrial (C/C++) and 23 student (Java) code reviews, detecting 388 and 371 defects, respectively. First, we discovered that 75 percent of defects found during the review do not affect the visible functionality of the software. Instead, these defects improved software evolvability by making it easier to understand and modify. Second, we created a defect classification consisting of functional and evolvability defects. The evolvability defect classification is based on the defect types found in this study, but, for the functional defects, we studied and compared existing functional defect classifications. The classification can be useful for assigning code review roles, creating checklists, assessing software evolvability, and building software engineering tools. We conclude that, in addition to functional defects, code reviews find many evolvability defects and, thus, offer additional benefits over execution-based quality assurance methods that cannot detect evolvability defects. We suggest that code reviews may be most valuable for software products with long life cycles as the value of discovering evolvability defects in them is greater than for short life cycle systems.