Deformation-Strength Relationships in Short-Term Tension of Heat-Resistant Materials

The analysis of 124 curves obtained in short-term tensile tests demonstrate that they can be described by varying strain hardening and softening characteristics. Different stress–strain curves can be produced at invariable yield strength and ultimate strength and interrelated proportional variations of the above characteristics. To determine some specific stress–strain curve, it is necessary to take account of yield strength and ultimate strength as well as strain corresponding to the latter. The relations between yield strength, ultimate strength and hardening and their practically complete absence between these parameters and softening were statistically established.     

Comparison of Two Statistical Models for the Calculation of Collisions of Particles in Isotropic Turbulence

Two models are given for determining the collision rate of inertial particles in a homogeneous isotropic turbulence. The advantages and disadvantages of the known models of particle collisions are discussed. One of the models suggested by us is based on the assumption that the joint probability density function of gas and particle velocities is a Gaussian distribution. The second model follows from the kinetic equation for the probability density of the relative velocity of two particles. These two models are compared with each other and with the available data of direct numerical simulation.     

Dynamic Effects of Submillimeter Wave Radiation on Biological Objects of Various Levels of Organization

We have presented an overview of the literature and of our experimental data on the influence of electromagnetic radiation in the submillimeter spectral region on biological objects of molecular, cellular, and organism levels. Possible physical mechanisms involved and the reasons for limited development of the research in this spectral range are discussed.     

Stress-strain relations in elastoplastic solids with Dugdale-type cracks

Mechanical behavior of a two-dimensional elastoplastic solid with rectilinear cracks is investigated. Plastic strip model is used to reduce plasticity problem to the equivalent linear elasticity formulation. Two realizations of the mixed mode plastic strip model are considered: in-line plastic strips as proposed by Becker and Gross [Int. J. Fract. 37 (1988) 163], and inclined plastic strips of Panasyuk and Savruk [Appl. Mech. Rev. 47 (1994) 151]. The effective mechanical response predictions are based on the procedure presented in Kachanov et al., [Appl. Mech. Rev. 47 (1994) 151]. Stress-strain relations are obtained for parallel and randomly oriented non-interacting cracks. Results are compared with known elastic solutions.     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

A 1.5-V 45-mW direct-conversion WCDMA receiver IC in 0.13-/spl mu/m CMOS

A 2-GHz direct-conversion receiver for wide-band code division multiple access (WCDMA) is presented. It includes two low-noise amplifiers (LNAs), an I/Q demodulator, and two sixth-order baseband channel select filters with programmable gain. Quadrature local oscillator (LO) signals are generated on chip in a frequency divider flip-flop. An external interstage filter between the LNAs rejects transmitter leakage to relax demodulator linearity requirements. A low-voltage demodulator topology improves linearity as well as demodulator output pole accuracy. The active-RC baseband filter uses a programmable servo loop for offset compensation and provides an adjacent channel rejection of 39 dB. Programmable gain over 71-dB range in 1-dB steps is merged with the filter to maximize dynamic range. An automatic on-chip frequency calibration scheme provides better than 1.5% corner frequency accuracy. The receiver is integrated in a 0.13-/spl mu/m CMOS process with metal-insulator-metal (MIM) capacitors. Measured receiver performance includes a 6.5-dB noise figure, IIP2 of +27 dBm, and IIP3 of -8.6 dBm. Power consumption is 45 mW.     

Effect of Strain Rate on Discontinuous Flow and Mechanical Characteristics of High-Nitrogenous Steel

Experimental study on the effect of strain rate on discontinuous flow and mechanical characteristics of the high-nitrogenous steel Kh23AG19F has been performed. Within the range of strain rates from 4.62 · 10^-5 to 1.85 · 10 ^-4 s^-1, discontinuous flow, reflected by serration on the tensile diagram, is chiefly determined by intergranular deformation mechanisms. Under strain rates over 1.85 · 10^-2 s^-1, combined deformation modes prevail, which cause a change in the character of discontinuous flow and transform a serrated tensile diagram into a wavy graph, with the yield stress of steel increased significantly.     

The effect of photon energy and temperature on the persistent tunneling photoconductivity effect in Al/δ(Si)-GaAs structures

The phenomenon of persistent tunneling photoconductivity was studied using the tunneling spectroscopy technique at liquid-helium temperature: the separation between the unoccupied levels in a δ-doped layer at the GaAs surface decreased after illumination. This decrease was due to an increase in the width of the quantum well of the δ-doped layer. For photon energies hv exceeding the GaAs band gap E _g , this increase in the width of the quantum well was related to the accumulation of positive charge in the depth of GaAs induced by the generation of the electron-hole pairs and photoionization of deep centers. For hv < E _g (including the case of CO₂ laser), only photoionization is important. The experimental data agree with the self-consistent calculations. The critical temperature for the effect has been determined (T _c = 45 K); at higher temperatures, the effect disappears.     

Mean vs. variance trade-off analysis in multi-antenna multi-user channels

In multi-user communications, the access point (AP) has several alternatives for distributing the scarce resources among users. Since there exists a trade-off between the global performance and the individual needs, an analytical framework to study fairness is derived, which completes the scope given by the existing fairness indexes in the literature. The framework proposed in this paper is a way to interpret fairness that has been inspired by portfolio selection; basically, it analyzes the mean vs. standard deviation trade-off. In this work, the target application is a multi-antenna AP transmitting simultaneously to several single-antenna terminals, although this framework is valid to analyze other procedures in multi-user communications.