Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.     

Piezoelectrically actuated four-bar mechanism with two flexible links for micromechanical flying insect thorax

In this paper, a piezoelectrically actuated four-bar mechanism with two flexible links is proposed to be used in a micromechanical flying insect robot wing thorax for stroke amplification. PZT-5H- and PZN-PT-based unimorph actuators are utilized at the input link of the four-bar for a compact and lightweight thorax transmission mechanism. The kinematics and dynamics of the proposed wing structure with two parallel four-bar mechanisms are analyzed, optimal four-bar link size selection method is introduced, and quasistatic forces generated at the wing are computed for evaluating the feasibility of the design. Using laser micromachining and folding techniques, prototype four-bar structures are constructed. In the experiments, for a 10/spl times/1/spl times/0.12 mm/sup 3/ PZT-5H actuator-based four-bar mechanism, the stroke amplification of around 20 - 25 is held, and an attached polyester wing is resonated at 29 Hz with around 90/spl deg/ flapping motion. These results match closely with the predicted theoretical values.     

Extractive Properties of Synergistic Mixtures of Dipicolinic Acid Diamides and Chlorinated Cobalt Dicarbollide

Extraction of Cs, Sr, Eu, U, Np, and Am with mixtures of dipicolinic acid diamides with chlorinated cobalt dicarbollide was studied. A synergistic effect was revealed.     

Multilayer power printed structures suitable for controlling EMI noises generated in power converters

Electromagnetic interference (EMI) noises generated in power converters are diffused on the surface of conductors. This means influences occur from radiated EMI noises emitted from power transmission lines as well as conducted EMI noises transmitted from them. EMI noises diffusing on the surface of conductors are generally difficult to control using conventional concentrated constant theory. Thus, a new approach based on distributed constant circuit theory is needed in order to control EMI noises. A power converter structure to control EMI noises using multilayer power printed circuit technology is studied in this paper. A structure which can control EMI noises should simultaneously satisfy two conditions, i.e., one to shut down and one to attenuate EMI noises. The structure satisfying these conditions is studied through simulations using the Transmission-Line Modeling Method. The simulations show that the diffusion of EMI noises is controlled by dividing the flow of currents produced by EMI noises into the horizontal and perpendicular directions. That is, the horizontal current flow is controlled inside using the differences in the resistance produced from differences between inner and outer diameter of power transmission lines and the perpendicular current flow can be controlled by properly designing the thickness of the dielectric layer sandwiched between P-and N-power transmission lines with the symmetrical structure. Moreover, it is confirmed by simulations and experiments that the attenuation of EMI noises is affected by the width of the power transmission lines. It is expected that the results obtained in this paper can provide important rules when designing power converters with EMI noise control functions which use the multilayer power printed circuit technology.     

Analogue switch for very low-voltage applications

A new analogue switch suitable for operation at very low-voltage supply in a standard CMOS technology is presented. The proposed switch is based on 'quasi-floating-gate' transistors and has a simple and compact structure. For illustrative purposes, two sample-and-hold circuits operating from a single supply voltage close to the threshold voltage of a transistor, and using the proposed technique, are presented. Experimental results obtained from prototypes in a 1.5 /spl mu/m CMOS technology are provided.     

An investigation of sugar extraction methods and the use of microwave power for date syrup processing: efficiency and color related considerations.

This study investigates the effect of extraction methods on the color of date syrup and the potential use of microwave power for syrup processing. Sugar solutions were extracted from dates by boiling, soaking and blending. Color and sugar content of the extracted solutions were measured, and the percentage of sugar extracted form the total fruit sugar determined. Boiling was found to be the most efficient method of extraction whereby 74% of total samples sugar was extracted. In contrast, only 54.2% of fruit sugar was extracted by blending and 42% by soaking. In addition, solutions extracted by soaking and blending had a foaming problem in the subsequent concentration process. The extraction method had no effect on the product final color. The extracted solution was concentrated using two heating methods: conventional and microwave heating at a 600 W capacity and a frequency of 2450 MHz applied at three power levels: 10, 7, and 6. In the heating process, 180 minutes were needed to achieve a 77% degrees Brix using convective heating, while it took 81, 138, and 166 minutes of microwave heating at power level 10, 7, and 6, respectively to achieve the same concentration. Water activity of the syrup was measured within a sugar content range of 50 to 80% degrees Brix and the sugar concentration at which the product is shelf stable was determined at 76%.     

Preschool Competency in Context: An Investigation of the Unique Contribution of Child Competencies to Early Academic Success.

The present concurrent study combined developmental and ecological considerations to examine the unique contribution of multiple preschool competencies to an indicator of early academic success. Participants included 195 Head Start children from 32 classrooms representative of a large, urban Head Start program. Dimensional (variable-centered) analyses revealed 3 distinct classroom competency dimensions (i.e., General Classroom Competencies, Specific Approaches to Learning, and Interpersonal Classroom Behavioral Problems). The first 2 of these dimensions were found to be uniquely associated with early academic success. Findings from typological (person-centered) analyses supported the dimensional findings. Typological analyses revealed 7 profiles of classroom competency distinguished by high scores on the dimensions of General Competencies and Approaches to Learning, and these profiles were found to relate differentially to the indicator of early academic success. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Techniques for microstructural characterization of powder-processed nickel-based superalloys

Methods are described for sample preparation of polycrystalline Ni-based superalloys in order to perform a detailed microstructural characterization. Specific techniques for the precise definition of the various phases present are outlined and these are shown to be useful for the measurement of size, volume fractions and distribution. A number of optical, scanning and transmission microscopy techniques are used to provide the necessary information.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.