Identification of microstructural zones and thermal cycles in a weldment of modified 9Cr-1Mo steel

This paper presents the results of a study on the microstructural and microchemical variations in a multipass Gas Tungsten Arc weld (GTAW) of modified 9Cr-1Mo steel. The changes brought about in the steel due to the heating and cooling cycles during welding and the subsequent effects due to reheating effects during multipass welding are described. Detailed analytical transmission electron microscopy has been carried to study the type and composition of the primary and secondary phases in this steel. The systematic changes in microstructural parameters such as Prior Austenite Grain Size, martensite lath size, number density, size and microchemistry of carbides, have been understood based on the different transformations that the steel undergoes during the heating and cooling process. Based on the observed microstructure, an attempt has been made to identify distinct microstructural zones and possible thermal cycles experienced by different regions of the weldment.     

组合斩波器为便携式应用增加带宽

对于精确地放大非常小的信号，简单的斩波放大器很适用，不过带宽有限。通过“组合“一个斩波器，带宽就能增加，使斩波器在更多的便携式设备中都有用武之地。     

Parallel path consistency

Filtering algorithms are well accepted as a means of speeding up the solution of the consistent labeling problem (CLP). Despite the fact that path consistency does a better job of filtering than arc consistency, AC is still the preferred technique because it has a much lower time complexity. We are implementing parallel path consistency algorithms on multiprocessors and comparing their performance to the best sequential and parallel arc consistency algorithms.^(1,2) (See also work by Kerethoet al. ⁽³⁾ and Kasif⁽⁴⁾) Preliminary work has shown linear performance increases for parallelized path consistency and also shown that in many cases performance is significantly better than the theoretical worst case. These two results lead us to believe that parallel path consistency may be a superior filtering technique. Finally, we have implemented path consistency as an outer product computation and have obtained good results (e.g., linear speedup on a 64K-node Connection Machine 2).     

Nanostructured polymer blends: Synthesis and structure

Nanostructured polymer blends prepared via anionic ring opening polymerizations of cyclic monomers in the presence of a pre-made polymer melt exhibit a number of special properties over traditional polymer blends and homopolymers. Here, we report on a simple and versatile method of in situ polymerization of macrocyclic carbonates in the presence of a maleic anhydride polypropylene (mPP) matrix and a surface-active compatibilizer (i.e. PC grafted onto a mPP backbone generated in situ) to yield a micro- and nanostructured polymer blends consisting of a polycarbonate (PC) minor phase, and a polypropylene (PP) major phase. By varying the processing conditions and concentration of the macrocyclic carbonate it was possible to reduce the size of the PC dispersions to an average minor diameter of 150 nm. NMR and TEM characterizations indicate that the PC dispersions do not influence crystal content in the PP phase. Overall, the results point to a simple strategy and versatile route to new polymeric materials with enhanced benefits.     

Mechanical improvement of concrete by irradiated polypropylene fibers

Fiber reinforced concrete (FRC) contains fibers physically mixed with gravel, sand, cement, and water. So far, adequate mechanical performance of FRC has been obtained at high cost and using complex technologies; important here is the geometry and surface characteristics of the polymers. We have modified polymeric‐fiber surfaces by using gamma radiation. Irradiated polypropylene (PP) fibers were submitted to 0, 5, 10, 50, and 100 kGy of gamma irradiation dosages. First, tensile strength of PP fibers was evaluated, and then fibers blended at 0, 1.0, 1.5, and 2.0% in volume with Portland cement, gravel, sand, and water. The highest values of compressive strength were obtained with irradiated‐fibers at 10 kGy and 1.5% in volume of fiber. The result is 101 MPa, as compared to 35 MPa for simple concrete without fibers. POLYM. ENG. SCI., 45:1426–1431, 2005. © 2005 Society of Plastics Engineers     

Microcomputer Control of a Residential Photovoltaic Power Conditioning System

Microcomputer-based control of a residential photovoltaic power conditioning system is described. The microcomputer is responsible for array current feedback control, maximum power tracking control, array safe zone steering control, phase-locked reference wave synthesis, sequencing control, and some diagnostics. The control functions are implemented using Intel 8751 single-chip microcomputer-based hardware and software. The controller has been tested in the laboratory with the prototype power conditioner and shows excellent performance.     

Two interviews with Reik.

This article describes two interviews with Theodor Reik. Explored topics include Reik's relationship with Sigmund Freud, psychoanalytic literature, and the history of the psychoanalytic movement. The author concludes with an analysis of his impressions of Reik. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Peracetic acid pretreatment of sugarcane bagasse for enzymatic hydrolysis: a continued work

Previous work has shown that the enzymatic hydrolysis of sugarcane bagasse could be greatly enhanced by peracetic acid (PAA) pretreatment. There are several factors affecting the enzymatic digestibility of the biomass, including lignin and hemicelluloses content, cellulose crystallinity, acetyl group content, accessible surface area and so on. The objective of this work is to analyze the mechanism of the enhancement of enzymatic digestibility caused by PAA pretreatment. Delignification resulted in an increase of the surface area and reduction of the irreversible absorption of cellulase, which helped to increase the enzymatic digestibility. The Fourier transform infrared (FTIR) spectrum showed that the absorption peaks of aromatic skeletal vibrations were weakened or disappeared after PAA pretreatment. However, the infrared crystallization index (N.O'KI) was increased. X‐ray diffraction (XRD) analysis indicated that the crystallinity of PAA‐treated samples was increased owing to the partial removal of amorphous lignin and hemicelluloses and probable physical change of cellulose. The effect of acetyl group content on enzymatic digestibility is negligible compared with the degree of delignification and crystallinity. The results indicate that enhancement of enzymatic digestibility of sugarcane bagasse by PAA pretreatment is achieved mainly by delignification and an increase in the surface area and exposure of cellulose fibers. Copyright © 2008 Society of Chemical Industry