Reduction of Vibration in Concentrated Winding Permanent Magnet Synchronous Motor by Means of Skew Effects of Rotor

Global warming and the problem of successfully incorporating environmental safeguards are promoting the need for a more power‐efficient motor. Therefore, as a driving source, permanent magnet synchronous motors (PMSMs) with concentrated winding are widely used in a variety of fields. However, a PMSM with a concentrated winding generates more vibration than one with a distributed winding because of the radial electromagnetic force. This paper describes the effect of a new skewed rotor on the characteristics of a concentrated winding PMSM. We investigated this effect by three‐dimensional finite element method (3D FEM) analysis and measurement. We also demonstrate that the proposed rotor is effective in reducing the radial electromagnetic force without decreasing motor efficiency. © 2014 Wiley Periodicals, Inc. Electr Eng Jpn, 187(2): 33–43, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22400     

Colored amorphous silica-based powder with TiN nanocrystals precipitated by ammonolysis of Ti–Si–O ternary glass

Coloration of amorphous silica powder containing titania was investigated by nitridation in an ammonia flow. The oxide precursors were obtained by the hydrolysis of a mixture of tetraethyl orthosilicate (TEOS) and tetrabutoxy titanium (TBT). The color changed with the amount of TBT in the mixture, the hydrolysis pH and the ammonolysis temperature. The original white color of the 8 mol% TBT powder hydrolyzed under basic pH conditions changed to pale goldenrod at 700°C, then to dark olive green at 800°C, and further darkened with increasing ammonolysis temperature. A steel-blue color appeared at 900°C for the powder obtained with 3 mol% TBT, and increased in darkness at 1000°C. A similar bluish color was observed for powders obtained by acidic hydrolysis after ammonolysis above 900°C, and this was independent of the amount of titania, although the chroma decreased with increasing firing temperature for the powder with 3 mol% TBT. The ammonolysis powder products were characterized using X-ray diffraction (XRD), electron probe micro analysis (EPMA), transmission electron microscopy-electron energy-loss spectroscopy (TEM-EELS), scanning transmission electron microscopy-high-angle annular dark-field imaging (STEM-HAADF) and Ti–K edge X-ray absorption fine structure (XAFS). The color change was related to both precipitated TiN nanocrystals and residual titanium in the amorphous silica matrix. The TiN exhibited a goldish reflection and also plasmonic absorption from light blue to gray depending on the TiN crystallite size. The plasmonic absorption and resonance of nanocrystalline TiN will be useful similarly to that of gold in nanotechnology for various kinds of energy application.     

Influence of design and operating conditions on the performance of tandem photoelectrochemical reactors

Solar-driven photoelectrochemical water splitting technology is a promising avenue for a sustainable hydrogen production. In this work, a comprehensive 2-dimensional model is developed and numerically simulated with hematite (α-Fe₂O₃) as the principal photoelectrode. The model evaluates light absorption, charge transport and electrochemical reactions to elucidate the effects of light transmitting materials, electrolyte height and electrolyte velocity on hydrogen and oxygen gas production. Results indicated that major losses in photocurrents are attributed to the transparent conducting oxide while losses due to the electrolyte increase with its height. Gas concentrations increase with increasing photocurrent densities and also in the direction of the flow. Gas bubbles however decrease with increasing electrolyte velocity. From these results, light reception in the reactor is uneven and poses a bigger challenge due to the bias in gas bubble distribution. Prospects of upscaling tandem schemes hence not only lie in the semiconductor material combinations but rather in the proper integration of system components and operating conditions.     

Bag of local landscape features for fitness landscape analysis

Evolutionary computation is a research field dealing with black-box and complex optimization problems whose fitness landscapes are usually unknown in advance. It is difficult to select an appropriate evolutionary algorithm and parameters for a given problem due to the black-box setting although many evolutionary algorithms have been developed. In this context, several landscape features have been proposed and their usefulness examined for understanding the problem. In this paper, we propose a novel feature vector by focusing on the local landscape in order to characterize the fitness landscape. The proposed landscape features are a vector form and composed of a histogram of quantized local landscape features. We introduce two implementation methods of this concept, called the bag of local landscape patterns (BoLLP) and the bag of evolvability (BoEvo). The BoLLP uses the fitness pattern of the neighbors of a certain candidate solution, and the BoEvo uses the number of better candidate solutions in the neighbors as the local landscape features. Furthermore, the hierarchical versions of the BoLLP and the BoEvo, concatenated feature vectors with different sample sizes, are considered to capture the landscape characteristic with various resolutions. We extract the proposed landscape feature vectors from well-known continuous optimization benchmark functions and the BBOB benchmark function set to investigate their properties; the visualization of the proposed landscape features, clustering and running time prediction experiments are conducted. Then the effectiveness of the proposed landscape features for the fitness landscape analysis is discussed based on the experimental results.     

Wide Color Variation in SiNO Thin Films Dispersed with Precipitated TiN Nano Particles

Amorphous thin films of Ti_1?ySi_y(N,O) with y ≥ 0.38 were prepared by reactive sputter deposition in a nitrogen atmosphere. Thermal annealing of the films in an ammonia flow above 800°C yielded Si(N,O) amorphous thin films dispersed with precipitated TiN nanosized particles. The film color changed with Si content y and the annealing conditions, from carrot orange to cream yellow in the as‐deposited films due to their oxynitride nature, and from dark green to canary yellow and from iron blue to horizon blue at respective annealing temperatures of 800°C and 900°C due to metallic nature of the TiN nanosized particles precipitated in the annealing.     

Additive Sintering,Postannealing, and Dielectric Properties of SrTaO2N

The maintaining of the chemical composition and electrical insulativity of SrTaO₂N ceramics was investigated during sintering and annealing, using powders prepared by the nitridation of Sr₂Ta₂O₇. Due to the low thermal stability of SrTaO₂N, the partial loss of SrO and nitrogen induced the formation of a TaO_0.9 impurity after heat‐treating at above 1100°C. The sintering additive SrCO₃ and postannealing in NH₃ were employed to compensate for the loss of SrO and nitrogen to obtain ceramics with the original chemical composition. The as‐sintered SrTaO₂N ceramics with various relative density (RD) were annealed in NH₃ to observe the recovery of color and electrical insulativity. It was found that the inner part of the well‐sintered samples with RD = 95.1% could not be recovered by annealing, and continued to exhibit semiconducting behavior and a black color. On the other hand, for the as‐sintered SrTaO₂N ceramics with RD < 84%, both the nitrogen content and electrically insulating behavior were completely recovered after annealing. The postannealed SrTaO₂N ceramics (RD = 83.3%) possessed a relatively large dielectric constant of 450 with a low dielectric loss of less than 0.1 at 100 Hz, almost independent of frequency and temperature.     

Enzymatic Analysis of Positional Distribution of Fatty Acids in Solid Fat by 1,3-Selective Transesterification with Candida antarctica Lipase B

A protocol for the analysis of the positional distribution of fatty acids (FA) in solid triacylglycerols (TAG) was developed using sn-1(3) selective alcoholysis catalyzed by immobilized Candida antarctica lipase B (CALB). One part by weight of solid fat and ten parts by weight of ethanol (99.5 %) were warmed to liquefy the fat. After adding 0.44 parts by weight of CALB, the mixture was shaken at 50 °C for 10 min then at 30 °C for 2.8 h. The recovery of 2-MAG after the 3-h transesterification reaction was ca. 85 % of the maximum theoretical yield (33 mol%), with the loss of 15 % attributable to the acyl migration from sn-2 to sn-1(3). The recovery was similar to that of the solvent-free alcoholysis of structured lipids, 1,3-dipalmitoyl, 2-oleoyl glycerol and 1,3-dioleoyl, 2-palmitoyl glycerol, conducted at 30 °C for 3 h. In contrast, the acyl migration from sn-1(3) to sn-2 was hardly observed. Because the detected acyl migration was only in the direction of sn-2 to sn-1(3), and not vice versa, it is proposed to determine the FA composition of the sn-2 position of TAG by the gas chromatographic analysis of 2-MAG fraction recovered from the enzymatic reaction mixture, and the FA composition of sn-1(3) position by a mass balance using the FA composition of TAG and of the sn-2 position as inputs. The procedure was successfully applied to palm oil and shea butter, and docosahexaenoic acid (DHA)-rich single cell oil from Aurantiochytrium sp. KH105 for the first time.     

Small-angle X-ray scattering studies on melting and recrystallization behaviors of poly(oxyethylene) crystallites in poly(d,l-lactide)/poly(oxyethylene) blends

Direct determination of the discrete distribution for crystalline lamellar thickness has been performed for poly(d,l-lactic acid)/poly(oxyethylene) (PDLLA/PEG) blends by conducting small-angle X-ray scattering (SAXS) measurements using synchrotron radiation. The PDLLA used was an random (racemic) copolymer of bio-based poly(l-lactic acid) (PLLA) and poly(d-lactic acid) (PDLA) with the lactide monomer ratio of l:d = 50:50. It is known that PLA is miscible with PEG in the amorphous state. In the current paper, we report comprehensive results on structural analyses of PDLLA/PEG blends in the course of heating and cooling process using SAXS to elucidate the change in the thickness distribution of the lamellae. As a consequence, it was found that the distribution of the lamellar thickness moves toward the larger value (in other words, lamellar thickening) as temperature approaches the melting point. Typically, the thickness distribution was dispersed in the range of 10–20 nm at room temperature and it changed toward 40 nm in the vicinity of the melting temperature. To the best of our knowledge, this is the first report of direct determination of the discrete distribution for the crystalline lamellar thickness and their in-situ changes in the course of the lamellar thickening process. As a result, the lamellar thickening was found to occur at much lower temperature for the blend samples with 10% and 20% of PDLLA contents as compared to the PEG 100% sample. This phenomenon can be ascribed to the melting point depression owing to the miscibility between PEG and PDLLA. Thereby, thinner lamellae were melted and thicker ones appeared at much lower temperature for the blends than for the PEG 100% sample. As for the average repeating distance (long period) of the lamellar stacks, an abrupt increase similar to the critical divergence was observed (from 25 nm to 50 nm) in the heating process. Not only for the melting behavior but also in the course of recrystallization, change in the lamellar-thickness distribution was uncovered, which shows strong hysteresis depending on what temperature the sample was cooled down from.     

Perpendicular oriented cylinders via directional coalescence of spheres embedded in block copolymer films induced by solvent annealing

Polystyrene-b-poly(methyl acrylate) (PS-b-PMA) block copolymer with PS volume fraction of 25.2 vol% was synthesized by atom transfer radical polymerization. Non-pretreated silicon wafers were used as the substrates to prepare perpendicular oriented PS cylinders in PMA matrix via solvent annealing which could induce the transformation of spheres to vertically oriented and hexagonally packed cylinders. The spherical microdomains were formed after the evaporation of solvents from the solutions of the block copolymer in selective solvents mixed from methanol, acetone and dichloromethane. The thickness of films could be as thick as 1000 nm, which were much thicker than usual cases and the cylinders came from the directional coalescence of the spheres, thus any pre-treatments of the substrates were not required for perpendicular orientation. The structures were characterized by small angle X-ray scattering (SAXS), transmission electron microscope (TEM), atom force microscopy (AFM) and grazing incidence small angle X-ray scattering (GISAXS).