Excitation Function Calculations of Neutron-Induced Reactions of Some Zirconium Target Isotopes

Nuclear structures with high performance materials will be critical for the success of future fusion energy. Zirconium alloys are extensively used for nuclear reactor core materials as fuel cladding and guide tubes due to excellent radiation and corrosion resistant properties. In this paper, the excitation functions of ⁹⁰Zr(n,2n)⁸⁹Zr, ⁹⁰Zr(n,α)⁸⁷Sr, ⁹¹Zr(n,p)⁹¹Y and ⁹²Zr(n,p)⁹²Y nuclear reactions were calculated for energies up to 25 MeV. Besides, ALICE/ASH and TALYS 1.6 codes were used for the cross section calculations. The obtained calculations were compared with the experimental data in the literature.     

Improvement of Palm Oil Biodiesel Filterability by Adsorption Methods

Palm oil biodiesel (POB) is characterized by a very high cold soak filtration time (CSFT), which places the acceptability of this biofuel at risk. Therefore, the effect of four adsorbents, namely diatomaceous earth, natural silicate (NS), neutral bleaching earth (NBE), and acid activated bleaching earth (AABE), at two levels of addition (1 and 5 wt%) or two temperatures (25 and 110 °C) on the precipitate content and CSFT of POB was investigated. The impact on total glycerin content, moisture content, and oxidative stability was also examined. All treatments significantly decreased the precipitate content, total glycerin content, and moisture content, but only treatments with NS, NBE, and AABE at 5 wt% and 25 °C achieved acceptable filterability. The OSI value was also decreased; however, it remained above the ASTM limit. Operational conditions of treatment with AABE were further optimized in a two‐factor, five‐level center composite design. The combination of 0.65 wt% AABE and 10 min at 25 °C decreased CSFT to below the ASTM limit. Lower adsorbent concentrations could be effective down to 0.44 wt%, given a corresponding increase in the contact time up to 30 min.     

Monte Carlo Simulations of 17.9–22.3 MeV Energetic Proton Irradiation Effects on bcc-Zirconium Fusionic Materials

Advanced fusion structural materials (FSMs) have impact role in terms of efficiency of nuclear energy production. Besides engineering and design of fusion reactors, radiation durability of FSMs is another valuable issue that cannot be ignored. 17.9–22.3 MeV proton irradiation of bcc-Zirconium Fusion Structural Material was evaluated by using Monte Carlo based simulation tools. Total binary reaction cross sections were respectively calculated as 1167.6 and 1273.92 mb for 17.3- and 22.3 MeV proton energies via TALYS-1.6 version. Additionally, residual production cross sections and total particle production cross sections were obtained and analyzed by the TALYS code. Radiation damage parameters as Displacement Per Atom (DPA) and Stopping Power (SP) were studied by SRIM-2013 version. FLUKA 2011.1 used for only DPA calculations and making a complete comparison with the other calculation results. SP and Number of Secondaries were found by using GEANT4.10.p.04 version simulations. Natural Zr(p,x) reactions were studied in the given energy values in the plane of reaction probability and radiation damage calculations.     

A methodology for predicting regional freight traffic in developing countries

The prime concern of transportation planners in developing countries is how to collect and transfer data into models as simple and as effective as possible and obtain solutions in the shortest time.

In this study, a methodology which utilizes multivariate statistical analysis techniques for travel estimation is presented. The two simple and convenient techniques namely Cluster Analysis and Principal Component Analysis, are used for the evaluation of available data. The traffic demand is expressed as a function of principal components which are determined independently as a small set of variables to represent total system variability. A stepwise regression analysis is carried out to derive the traffic demand‐principal component relationship. The proposed methodology is then applied to Southeastern Anatolia Regional Development Project in Turkey.     

Effect of various pore formers on the microstructural development of tape-cast porous ceramics

Various types of pore formers have been used for the fabrication of ceramics with controlled porosity. This study addresses a detailed and systematic comparison of different pore formers (e.g. graphite, polymethyl methacrylate, sucrose and polystyrene) with distinct features such as size, distribution and morphology of particles and decomposition/oxidation behavior. Investigations also involve their effect on the rheological properties of the slurries and the microstructural development of laminated porous ceramic tapes.Morphological features of the pore former particles were characterized using laser diffraction, B.E.T. surface area measurement and scanning electron microscopy (SEM) techniques as their thermal decomposition/oxidation behavior were determined by thermogravimetric analysis (TGA) and differential thermal analysis (DTA) methods. Tape compositions were developed and optimized in order to incorporate identical volumetric loadings of the materials in the tape formulations with different pore formers for a reliable comparison of their pore forming characteristics. Porous yttria stabilized zirconia (YSZ) ceramics were fabricated without macroscopic defects (e.g. cracks, warpage and delamination) by developing heating profiles based on the identified thermal properties of the pore formers. Characterization of the sintered porous ceramics by SEM and mercury intrusion porosimetry techniques revealed novel relationships between the physical properties of the utilized pore formers, processing parameters and final pore structures.     

Diffusion bonding of electroless Ni plated WC composite to Cu and AISI 316 stainless steel

In this study, a composite containing WC (Tungsten Carbide) and Ni was produced by two different processing routes. Electroless Ni coated WC powders were consolidated and sintered at 1200 °C. Diffusion bonding couples of WC(Ni)-electrolytic Cu, WC(Ni)-AISI 316 stainless steel and WC(Ni)-WC(Ni) were manufactured by using a preloaded compression system under Ar atmosphere. Diffusion bonding was carried out at varying bonding temperatures; 750 °C for (WC)Ni-Cu diffusion couple and 1200 °C for (WC)Ni-(WC)Ni and (WC)Ni-AISI 316 stainless steel diffusion couples. Standard metallographic techniques, Scanning Electron Microscopy and a shear test were employed to characterize the microstructure of bondline and mechanical properties of each diffusion couple, respectively.