Effects of material combination on laser beam drilling of a metal foil using a cover plate

This research investigated the microdrilling characteristics of metal foils depending on the materials of the cover plates and metal foils in the cover plate-laser beam machining (c-LBM) process, which is a method to achieve better quality in metal foil machining with a given piece of equipment. Laser beam drilling using a nanosecond pulsed laser was carried out on 10-µm-thick stainless steel 304 (STS304), nickel, and copper foils with 100-µm-thick cover plates of each material. Consequently, STS304 was found to be an effective cover plate material for reducing the hole diameter and spatter deposition on metal foils. Compared to the results without using a cover plate, the average hole diameter and the area of spatter deposition decreased by up to 77% and 96%, respectively, by using the STS304 cover plate. Meanwhile, the thermal deformation of the STS304 and nickel foils was prevented by using a cover plate, while the copper foil was barely deformed even without a cover plate. Lastly, it was remarkable that the copper foil was drilled with approximately 67% lower pulse energy than the effective minimum pulse energy required to drill it by using the STS304 cover plate, resulting in a smaller hole with little spatter.     

Effect of stents coated with a combination of sirolimus and alpha-lipoic acid in a porcine coronary restenosis model

The aim of this study was to evaluate antiproliferative sirolimus- and antioxidative alpha-lipoic acid (ALA)-eluting stents using biodegradable polymer [poly-l-lactic acid (PLA)] in a porcine coronary overstretch restenosis model. Forty coronary arteries of 20 pigs were randomized into four groups in which the coronary arteries had a bare metal stent (BMS, n = 10), ALA-eluting stent with PLA (AES, n = 10), sirolimus-eluting stent with PLA (SES, n = 10), or sirolimus- and ALA-eluting stent with PLA (SAS, n = 10). A histopathological analysis was performed 28 days after the stenting. The ALA and sirolimus released slowly over 30 days. There were no significant differences between groups in the injury or inflammation score; however, there were significant differences in the percent area of stenosis (56.2 ± 11.78 % in BMS vs. 51.5 ± 12.20 % in AES vs. 34.7 ± 7.23 % in SES vs. 28.7 ± 7.30 % in SAS, P < 0.0001) and fibrin score [1.0 (range 1.0–1.0) in BMS vs. 1.0 (range 1.0–1.0) in AES vs. 2.0 (range 2.0–2.0) in SES vs. 2.0 (range 2.0–2.0) in SAS, P < 0.0001] between the four groups. The percent area of stenosis based on micro-computed tomography corresponded with the restenosis rates based on histopathological stenosis in different proportions in the four groups (54.8 ± 7.88 % in BMS vs. 50.4 ± 14.87 % in AES vs. 34.5 ± 7.22 % in SES vs. 28.9 ± 7.22 % in SAS, P < 0.05). SAS showed a better neointimal inhibitory effect than BMS, AES, and SES at 1 month after stenting in a porcine coronary restenosis model. Therefore, SAS with PLA can be a useful drug combination for coronary stent coating to suppress neointimal hyperplasia.     

Revisiting Statistical Design and Analysis in Scientific Research

Statistics is essential to design experiments and interpret experimental results. Inappropriate use of the statistical analysis, however, often leads to a wrong conclusion. This concept article revisits basic concepts of statistics and provides a brief guideline of applying the statistical analysis for scientific research from designing experiments to analyzing and presenting the data.     

Characterization of centrifugally atomized Al-12Si-5Fe-3Cu-1Mg(wt%) alloy powder and extruded rod

The Al-12Si-5Fe-3Cu-1Mg(wt%) alloy was rapidly solidified by centrifugal atomization. The microstructural characteristics of rapidly solidified powder and the microstructure changes with heat treatment were investigated in terms and related to powder size. The microstructures of the powder consisted of dendritic -Al, eutectic phase, Cu-rich phase, and needle-like intermetallic compounds. These phases were much finer than that of ingot cast structure and the size decreased with increasing cooling rate. The X-ray diffraction of the atomized powders revealed the presence of non-equilibrium 3-(AlFeSi) intermetallic phase. This phase appeared to transform to an equilibrium -(AlFeSi) phase by heating at temperatures above 470°C. The extruded rod which was hot extruded at 360°C with an extrusion ratio of 40:1 also revealed the presence of the -(AIFeSi) intermetallic phase. Using DSC, the exothermic peak due to precipitation from the supersaturated -Al matrix was observed in the range of 200–250°C during continuous heating of atomized powder, and the size of the peaks increased with decreasing powder size.     

Transformation of a thin-walled solid model into a surface model via solid deflation

A simplified geometric model with lower dimensionality, such as a mid-surface model, is often preferred over a detailed solid model for the analysis process, if the analysis results are not seriously impacted. In order to derive a mid-surface model from a thin-walled solid model, in this paper, we propose a novel approach called the solid deflation method. In this method, a solid model is assumed to be created by using air to inflate a shell that comprises the surface of the solid model. First, the model is simplified by the removal of any detailed features whose absence would not alter its overall shape. Next, the solid model itself can be converted into a degenerate solid model with zero thickness. Finally, a surface model is generated by splitting large faces paired in the thinned solid model, selecting one face per pair for creating a sheet model, and sewing the selected faces. Using this method, a more practical and usable mid-surface model can be very efficiently generated from a solid model because it can circumvent not only the tedious trimming and extension processes of the medial axis transformation method but also the time-consuming patch joining process of the mid-surface abstraction approach.     

Theoretical and experimental characterization of wettability of various nanolens arrayed polymer surfaces replicated with nanodimpled aluminum mold insert

Various types of polymer surfaces with a nanolens array, which has an entrant shape with a low aspect ratio, were fabricated and the wettability of the fabricated surfaces was evaluated in both theoretical and experimental ways. The nanolens array was replicated on three different polymer surfaces of polydimethylsiloxane (PDMS), cyclic olefin copolymer (COC), and polymethylmethacrylate (PMMA) by means of replica molding and hot embossing with a nanodimpled aluminum mold that was manufactured by a chemical oxidation process. From the theoretical and experimental evaluations of the wettability it was found that the measured contact angles were very similar with the theoretically estimated ones and also the hydrophilicity and hydrophobicity of the hydrophilic PMMA and hydrophobic PDMS, respectively, surfaces were reinforced by the nanolens array within the Wenzel wetting state.     

Device reliability under electrical stress and photo response of oxide TFTs

Abstract— The stability of oxide TFTs has been the main focus of this research and is probably the most crucial requirement for the successful application to flat‐panel displays. Although the high Fermi level of oxide semiconductors makes TFTs basically stable under electrical stress, the device reliability under diverse variations of electrical stress is affected by materials such as active semiconductors and gate insulators, processes for the formation of back/front channels and passivation layers, and device configurations among other things. How these factors affect the device reliability have been investigated and a review of the stability is presented. In addition, several categories of the light instability of oxide TFTs is presented and the origin is discussed.