Methyl tert-butyl ether decomposition over heteropoly acid catalyst in a cellulose acetate membrane reactor

In this study the methyl tert-butyl ether (MTBE) decomposition over H₃PW₁₂O₄₀ was carried out in a cellulose acetate membrane reactor. The permeability of methanol through the cellulose acetate membrane was about 30 and 300 times higher than that of either isobutene or MTBE, respectively. The isobutene selectivity in the fixed bed reactor was only slightly higher than the methanol selectivity due to the side reaction. In the cellulose acetate membrane reactor, however, the isobutene selectivity in the rejected stream was 68% and the methanol selectivity in the permeated stream was up to 97%. The MTBE conversion in the membrane reactor was about 7% higher than that in the membrane-free fixed bed reactor under the same reaction conditions. The enhanced performance of the membrane reactor in this reversible reaction was mainly due to the selective permeation of methanol which resulted in a methanol-deficient condition suppressing MTBE synthesis reaction.     

Preparation and characterization of a proton‐exchange membrane by the radiation grafting of styrene onto polytetrafluoroethylene films

Radiation‐induced simultaneous grafting of styrene onto polytetrafluoroethylene (PTFE) films and the subsequent sulfonation in the chlorosulfonic acid/dichloroethane were investigated. The effects of the main radiation grafting conditions, such as the type of solvents, irradiation dose, dose rate, the styrene concentrations, etc., on the degree of grafting (DOG) were studied. To elucidate the influence of both the grafting and sulfonation conditions on the properties of the PTFE‐g‐polystyrene‐sulfonic acid (PSSA) membranes, the sulfonation conditions, including the sulfonation temperature and the concentration of the ClSO₃H with respect to the DOG, were systematically evaluated. The grafted and sulfonated membranes were characterized by FTIR–ATR spectra, ion‐exchange capacity (IEC), water uptake, thickness measurement, etc. The as‐prepared PTFE‐g‐PSSA membranes in this work showed a good combination of a high IEC (0.85–2.75 meq g^?1), acceptable water uptake (8.86–56.9 wt %), low thickness, and volume expansion and/or contraction. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1415–1428, 2006     

Synthesis and characterization of in situ polymerized segmented thermoplastic elastomeric polyurethane/layered silicate clay nanocomposites

Nanocomposites based on thermoplastic elastomeric polyurethane (TPU) and layered silicate clay were prepared by in situ synthesis. The properties of nanocomposites of TPU with unmodified clay were compared with that of organically modified clay. The nanocomposites of the TPU and organomodified clay showed better dispersion and exhibited superior properties. Exfoliation of the clay layers was observed at low organoclay contents, whereas an intercalated morphology was observed at higher clay contents. As one of major purposes of this study, the effect of the silicate layers in the nanocomposites on the order–disorder transition temperature (T_ODT) of the TPU was evaluated from the intensity change of the hydrogen‐bonded and free carbonyl stretching peaks and from the peak position change of the N? H bending peak. The presence of the organoclay increased T_ODT by approximately 10°C, which indicated improved stability in the phase‐separated domain structure. The layered silicate clay caused a tremendous improvement in the stiffness of the TPU; meanwhile, a reduction in the ultimate elongation was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3048–3055, 2006     

Molecular species of 1-O-alk-1′-enyl-2-acyl-, 1-O-alkyl-2-acyl- and 1,2-diacyl glycerophospholipids in Japanese oysterCrassostrea gigas (Thunberg)

Molecular species of 1-O-alk-1′-enyl-2-acyl-, 1-O-alkyl-2-acyl-, and 1,2-diacyl-sn-glycero-3-phosphoethanolamine (EPL) andsn-glycero-3-phosphocholine (CPL) of Japanese oysterCrassostrea gigas were analyzed by selectedion monitoring gas chromatography/mass spectrometry using electron impact ionization. The characteristic fragment ions, [RCH=CH+56]⁺ due to the alkenyl residue in thesn-1 position and [RCO+74]⁺ due to the acyl residue in thesn-2 position of alkenylacylglycerols, [R+130]⁺ due to the alkyl residue in thesn-1 position and [RCO+74]⁺ due to the acyl residue in thesn-2 position of alkylacylglycerols, [RCO+74]⁺ due to the acyl residues in thesn-1 and/orsn-2 positions of diacylglycerols, and [M−57]⁺ being indicative of the corresponding molecular weight, were used for structural assignments. For alkenylacyl EPL and CPL, 19 and 16 molecular species were determined, respectively. Two molecular species, 18∶0alkenyl-22∶6n−3 and 18∶0-alkenyl-22∶2-non-methylene interrupted diene (NMID), amounted to 53.2% and 47.9%, respectively. The alkylacyl EPL and CPL consisted of 16 and 20 molecular species, respectively, and the prominent components were 18∶0alkyl-22∶2NMID, 20∶1alkyl-20∶1n−11 (27.4%) and 20∶1alkyl-20∶2NMID (16.3%) in the former, and 16∶0alkyl-20∶5n−3 (23.0%) and 16∶0alkyl-22∶6n−3 (21.6%) in the latter. For the diacyl EPL and CPL, 14 and 51 molecular species were determined, respectively. The major molecular species were 18∶0–20∶5n−3 (37.4%), 16∶0–20∶5n−3 (14.2%) and 18∶1n−7–22∶2NMID (13.2%) in the former, and 16∶0–20∶5n−3 (33.4%) and 16∶0–22∶6n−3 (22.3%) in the latter. It was found that there were significant differences in the molecular species between the alkylacyl and diacyl EPL and the alkylacyl and diacyl CPL; the number of molecular species was larger in CPL than in EPL, while the number of total carbons and double bonds of the major molecular species were larger in the EPL than in the CPL. Alkenylacyl EPL were similar to alkenylacyl CPL in molecular species composition.     

Durable antimicrobial treatment of cotton fabrics using N‐(2‐hydroxy)propyl‐3‐trimethylammonium chitosan chloride and polycarboxylic acids

N‐(2‐hydroxy)propyl‐3‐trimethylammonium chitosan chloride (HTCC), a water‐soluble chitosan quaternary ammonium derivative, was used as an antimicrobial agent for cotton fabrics. HTCC has a lower minimum inhibition concentration (MIC) against Staphylococcus aureus, Klebsiella pneumoniae, and Escherichia coli compared to that of chitosan; however, the imparted antimicrobial activity is lost on laundering. Thus crosslinking agents were utilized to obtain a durable antimicrobial treatment by immobilizing HTCC. Several crosslinkers such as dimethyloldihydroxyethylene urea (DMDHEU), butanetetracarboxylic acid (BTCA), and citric acid (CA) were used with HTCC to improve the laundering durability of HTCC treatment by covalent bond formation between the crosslinker, HTCC and cellulose. The polycarboxylic acid treatment was superior to the DMDHEU treatment in terms of prolonged antimicrobial activity of the treated cotton after successive laundering. Also, the cotton treated with HTCC and BTCA showed improved durable press properties without excessive deterioration in mechanical strength or whiteness when compared to the citric acid treatment. With the addition of only 0.1% HTCC to BTCA solutions, the treated fabrics showed durable antimicrobial activity up to 20 laundering cycles. The wrinkle recovery angle and strength retention of the treated fabrics were not adversely affected with the addition of HTCC. Therefore, BTCA can be used with HTCC in one bath to impart durability of antimicrobial activity along with durable press properties to cotton fabric. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1567–1572, 2003     

Preparation and characterizations of interpenetrating polymer network hydrogels of poly(ethylene oxide) and poly(methyl methacrylate)

Interpenetrating polymer network (IPN) hydrogels based on poly(ethylene oxide) and poly(methyl methacrylate) were prepared by radical polymerization using 2,2‐dimethyl‐2‐phenylacetophenone and ethylene glycol dimethacrylate as initiators and crosslinkers, respectively. The IPN hydrogels were analyzed for sorption behavior at 25°C and at a relative humidity of 95% using dynamic vapor sorption. The IPN hydrogels exhibited a relatively high equilibrium water content in the range of 13–68%. The state of water in the swollen IPN hydrogels was investigated using differential scanning calorimetry. The free water in the hydrogels increased as the hydrophilic content increased. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 258–262, 2003     

Fabrication of a gradient refractive index preform using laminar shear mixing

A gradient refractive index rod was successfully prepared by a new fabrication method using laminar shear mixing, and a graded index polymer optical fiber that satisfied IEEE1394b was obtained from the method. To fabricate the gradient refractive index rod, a liquid monomer mixture with a relatively low refractive index was placed in a prepared cylindrical glass reactor and a transparent polymer rod with a higher refractive index was introduced at the center of the reactor. The reactor and the polymer rod were then rotated concurrently with a small rotating speed difference to generate a Couette flow in the liquid phase. The centrifugal force generated by rotation and the polymer diffusion into the liquid monomer mixture developed a graded concentration profile in a radial direction. The Couette flow could reduce the concentration fluctuation in a tangential direction. In addition, the graded index profile could be controlled by the copolymer composition of the rod and its diameter. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1100–1104, 2005     

Molecular modeling of antibody-antigen complexes between the Brucella abortus O-chain polysaccharide and a specific monoclonal antibody

A molecular model of the binding site of an anti-carbohydrateantibody (YsT9.1) has been developed using computer-assistedmodeling techniques and molecular dynamics calculations. Sequencehomologies among YsT9.1 and the Fv regions of McPC603, J539and human Bence-Jones protein REI, all of which have solvedcrystal structures, provided the basis for the modeling. Thegroove-type combining site model had a topography which wascomplementary to low energy confonners of the polysaccharide,a Brucella O-antigen, and the site could be almost completelyfilled by a pentasaccharide epitope in either of two dockingmodes. Putative interactions between this epitope and the antibodyare consistent with the known structural requirements for bindingand lead to the design of oligosaccharide inhibitors that probethe veracity of the modeled docked complex. Ultimately boththe Fv model and the docked complex will be compared with independentcrystal structures of YsT9.1 Fab with and without pentasaccharideinhibitor, currently at the stage of refinement.     

Electromechanical behavior of hybrid carbon/glass fiber composites with tension and bending

To understand the smart (i.e., good memory) characteristics of hybrid composites of carbon fibers (CFs) and glass fibers (GFs) with epoxy resin as a matrix, the changes in the electrical resistance of composites with tension and on bending were investigated. The electrical resistance behavior of composites under tension changed with the composition of the CF/GF, as well as with the applied strain. The fractional electrical resistance increased slowly with increasing strain within a relatively low strain region. However, with further loading it increased stepwise with the strain according to the fracture of the CF layers. The strain sensitivity of the samples increased with increasing CF weight percentage, and the samples incorporating more than 40 wt % CF showed a strain sensitivity higher than 1.54 for a single CF. The changes in the fractional electrical resistance with bending were not so dominant as those with tension. This difference was attributed to the action of two cancelling effects, which are the increasing and decreasing fractional electrical resistance due to tension and compression with bending, respectively. On recovery from a large applied bending, the fractional electrical resistance decreased slowly with unloading because of the increase of contacts between the fibers that resulted from the reorganization of ruptured CFs during the recovery. Even the composites incorporating a relatively small CF content showed an irreversible electrical resistance with both tension and bending. However, the strain sensitivity being larger with tension than with bending is ascribed to the difference in their mechanical behaviors. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2447–2453, 2002     

Degradation of a textile azo dye by pulsed arc discharge to the surface of wastewater

The pulsed arc discharge to the surface of wastewater was applied to the degradation of a textile azo dye (Acid Red 27). A high-voltage electrode (discharging electrode) was vertically placed above the surface of the wastewater while the wastewater itself was grounded. The pulsed arc discharge occurred between the tip of the discharging electrode and the surface of the wastewater, producing various oxidative species. Oxygen was used as the working gas instead of air to prevent nitrogen oxides from forming. The effect of several parameters on the chromaticity and chemical oxygen demand (COD) removal was examined. The results obtained showed that the chromaticity of the wastewater was completely removed by this process and the COD also decreased significantly. It has been found that ozone formed in the gas phase mainly affects the removal of the dye. The contribution of other effects such as ultraviolet light emission and OH radical formation during the arc discharge to the degradation of the dye was found to be less than 15%. For the present reactor system, the optimum pH, pulse repetition rate and agitation speed were found to be 3.0, 110 Hz and 300 rpm, respectively.