电子式电能表的接线方式及误差分析

针对电子式电能表与机械式电能表之间的不同结构和工作原理，提出应根据不同应用情况来决定其安装接线方式。另外通过对电子式电能表做线损、三相负荷平衡率和走字试验的实例分析，认为应根据两者不同的结构状况和工作原理才能保证正确计量。     

绕片式冷却器性能计算软件开发

介绍绕片式冷却器性能计算的原理，其软件开发的思路及软件的特点。图2     

New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.     

Hydrothermal Synthesis of Magnesium Aluminate Platelets

Magnesium aluminate (MgAl₂O₄) platelets were first synthesized by hydrothermal treatment of γ-AlO(OH) in a magnesium nitrate aqueous solution at 400°C. The platelets are 100–200 nm in width and 25 nm in thickness. The influence of temperature, the anions of the magnesium salt, the amount of magnesium salt, and precursor pH on the formation of such structure was investigated. The experimental results indicated that the anions of the magnesium salt and precursor pH could have a significant influence on the growth of MgAl₂O₄. MgAl₂O₄ formation followed the in situ transformation mechanism, which was the reason why the MgAl₂O₄ crystallites had a platelet morphology.     

Study of Liquid Phase Shifter for ICRF on EAST

A method of current drive with Ion Cyclotron Range of Frequency （ICRF） on Experimental Advanced Superconducting Tokomak （EAST） is described. A variety of liquid silicon oil heights in the phase shifter will bring the phase difference to the current drive. It is found that the current drive can be achieved by using the phase shifter. The liquid phase shifter is one of the impedance matching systems too.     

Effects of tube rupture modeling and the parameters on the analysis of multiple steam generator tube rupture event progression in APR1400

A multiple steam generator tube rupture (MSGTR) event in APR1400 has been investigated using the best estimate thermal hydraulic system code, MARS1.4. The effects of the parameters such as the number of ruptured tubes, rupture location, affected steam generator on the analysis of the MSGTR event in APR1400 are examined. In particular, tube rupture modeling methods, single tube modeling (STM) and double tube modeling (DTM), are compared. The APR1400 is found to have the capability of allowing more than 30 min to operators for the MSGTR event of five tubes. The effects of rupture location on the MSSV lift time is not significant in the case of STM, but the MSSV lift time for tube-top rupture is found to be 25.3% larger than that for rupture at the hot-leg side tube sheet in the case of DTM. The MSSV lift time for the cases that both steam generators are affected (4C5x, 4C23x) are found to be larger than that of the single steam generator cases (4A5x, 4B5x) due to a bifurcation of the primary leak flow. The discharge coefficient of Cd is found to affect the MSSV lift time only for a smaller value of 0.5. It is found that the most dominant parameter governing the MSSV lift time is the leak flow rate. Whether any modeling method is used, it gives the similar MSSV lift time if the leak flow rate is close, except in the case where both steam generators are affected. Therefore, the system performance and the MSSV lift time of the APR1400 are strongly dependent on the break flow model used in the best estimate system code.     

三氯乙酰氯的合成与应用

综述了三氯乙酰氯的合成方法及其在农药、医药等领域中的应用。     

提高干压各向异性SrM磁体磁性能的方法

以Y30H-1的SrM预烧料为原料,通过对二次添加剂、二次球磨及烧结曲线的调整,做出了Br≥380mT,Hcb≥240kA穖-1,Hcj≥250kA穖-1,(BH)max≥27.0kJm-3的干压各向异性锶铁氧体产品。     

Al2O3对唐钢高炉炉渣性能的影响

针对唐钢近2年提高进口矿配比后，Al2O3含量升高对炉渣流动性带来的不利影响，对唐钢高炉的炉渣性能进行了试验研究。并结合国内同行业的生产实践经验，从理论上分析了炉渣中Al2O3及MgO的适宜含量范围，着重论述了唐钢所处冀东矿区条件下降低Al2O3的主要途径及适应高Al2O3炉渣的具体措施。     

An anti-plane crack perpendicular to the weak/micro-discontinuous interface in a bi-FGM structure with exponential and linear non-homogeneities

Treated was an anti-plane crack perpendicular to the interface of an exponential-type FGM strip bonded to another linear-type FGM substrate with infinite thickness. Through Fourier integral transform, the problem was reduced as a Cauchy singular integral equation, which was further solved numerically by the Lobatto–Chebyshev collocation method. Based on the numerical solution, the effects of the geometrical and physical parameters on the stress intensity factor (SIF) were analyzed and the following conclusions were obtained: (a) A notable discrepancy between the interface-perpendicular crack and the interfacial one is that, to reduce the weak-discontinuity of interface or to make the interface micro-discontinuous will not necessarily decrease the SIF of the former, but will surely decrease that of the latter. (b) When a crack tip is situated very near to the interface (or free surface), its SIF will be high and totally dominated by the interface (or free surface). (c) To increase the stiffness of the FGM on one side of the interface is beneficial to preventing the crack on the other side from growing toward the interface. Besides, some practical suggestions were further given for material design in the field of composites.