A fast method for the determination of the efficiency coefficient of bare CR-39 detector

A fast and simple method for the determination of the efficiency coefficient (η) of bare CR-39 detector is presented and discussed. The efficiency coefficient of bare CR-39 detector is then calculated by different ways and the obtained values are found to be comparable to each other. The average value of η of bare CR-39 is found to be 0.20 ± 0.01 tracks cm⁻² day⁻¹ per Bq m⁻³.     

Accelerated weathering-induced degradation of poly(lactic acid) fiber studied by near-infrared (NIR) hyperspectral imaging

Hydrolysis degradation of a set of drawn poly(lactic acid) (PLA) fibers was induced by an accelerated weathering test, radiating ultraviolet (UV) light under a certain temperature and humidity. The fine features of the transient behavior of the PLA fibers were captured by near-infrared (NIR) hyperspectral imaging. The PLA fibers showed a gradual decrease in mechanical property (e.g., tensile strength), indicating hydrolysis degradation. Thus, the detailed analysis of the spectral variation, in turn, offers useful information on the molecular-level degradation behavior of the drawn PLA fibers. The variation of the spectral intensity as well as band position shift of the crystalline band of PLA was analyzed. The spectral intensity of the crystalline band of PLA showed gradual decrease, suggesting the decrease in molecular weight induced by the hydrolysis degradation. In addition, the crystalline band also exhibited a coinciding shift to the lower wavenumber direction with the weathering test, revealing cleavage-induced crystallization of the PLA samples. Consequently, the hydrolysis degradation induced by the weathering test substantially accelerates predominant degradation of the amorphous structure of the PLA and such variation of the molecular structure, in turn, brings less ductility to the PLA fiber.     

High-intensity multi-bunch beam generation by a photo-cathode RF gun

A multi-bunch photo-cathode RF gun system has been developed as an electron source for the production of intense quasi-monochromatic X-rays based on inverse Compton scattering. The desired multi-bunch beam is 100 bunches/pulse with a total charge of 500 nC and a bunch spacing of 2.8 ns. We modified the gun cavity of a ‘BNL-type IV’ RF gun to allow a CsTe cathode plug in the end plate. The system uses a four-dipole chicane beam line to allow the injection of laser light normal to the cathode surface. We compensate the gun cavity beam loading caused by the high-intensity multi-bunch electron beam by injecting the laser pulse before RF power has filled the cavity. We have achieved a total intensity of 220 nC in 100 bunches with a bunch-to-bunch energy spread under 1.3% (peak-to-peak). This paper concentrates on experiments to generate the high-intensity multi-bunch beam with compensation of the bunch-to-bunch energy spread due to heavy beam loading.     

Fabrication of silicon nitride nanoceramics—Powder preparation and sintering: A review

Fine-grained silicon nitride ceramics were investigated mainly for their high-strain-rate plasticity. The preparation and densification of fine silicon nitride powder were reviewed. Commercial sub-micrometer powder was used as raw powder in the “as-received” state and then used after being ground and undergoing classification operation. Chemical vapor deposition and plasma processes were used for fabricating nanopowder because a further reduction in grain size caused by grinding had limitations. More recently, nanopowder has also been obtained by high-energy milling. This process in principle is the same as conventional planetary milling. For densification, primarily hot pressing was performed, although a similar process known as spark plasma sintering (SPS) has also recently been used. One of the advantages of SPS is its high heating rate. The high heating rate is advantageous because it reduces sintering time, achieving densification without grain growth. We prepared silicon nitride nanopowder by high-energy milling and then obtained nanoceramics by densifying the nanopowder by SPS.     

The complex aerodynamic footprint of desert locusts revealed by large-volume tomographic particle image velocimetry

Particle image velocimetry has been the preferred experimental technique with which to study the aerodynamics of animal flight for over a decade. In that time, hardware has become more accessible and the software has progressed from the acquisition of planes through the flow field to the reconstruction of small volumetric measurements. Until now, it has not been possible to capture large volumes that incorporate the full wavelength of the aerodynamic track left behind during a complete wingbeat cycle. Here, we use a unique apparatus to acquire the first instantaneous wake volume of a flying animal''s entire wingbeat. We confirm the presence of wake deformation behind desert locusts and quantify the effect of that deformation on estimates of aerodynamic force and the efficiency of lift generation. We present previously undescribed vortex wake phenomena, including entrainment around the wing-tip vortices of a set of secondary vortices borne of Kelvin–Helmholtz instability in the shear layer behind the flapping wings.     

A 60-ns 16-Mbit DRAM with a minimized sensing delay caused by bit-line stray capacitance

Discusses three new techniques that were implemented in a CMOS 60-ns 16-Mbit DRAM device. (1) A two-step half-conductive-state technique was used to control the conductivity of latch transistors, thus minimizing the time delay caused by bit-line stray capacitance. (2) The 'split-block row decoder' technique enabled the decoder layout within the 2.9- mu m cell pitch required for 16-Mbit integration density. The three transistors that are required per word line were split into two and one, placed on both sides of each word line, and alternately reversed on each side of the 2-Mbit cell array. (3) Additional dummy cells were added to the vacant spaces resulting from use of a twisted bit-line architecture, which reduces stray capacitance between adjacent bit lines. The overhead space required for all the dummy cells and twisted bit lines was thus held at 2.6 percent of the entire chip area.<>     

Coordinate-Based Evaluation of Two Dimensional Artefact Calibration Value as the Reference Standards for Coordinate Measuring Machines

Two dimensional standards are important materials which are used in the calibration and the verification of coordinate measuring machines. In several countries, the national metrology institutes or accredit laboratories provide the calibration services of the two dimensional standards such as ball plates, hole plates and grid plates. The metrological equivalence of the measurement standards among the calibration providers is validated through the key comparison program. In the previous key comparison for a ball plate and a hole plate, the equivalences among the participants’ calibration results were verified on the distances between the No. 1 ball/hole (i.e., the origins of the workpiece coordinates) and other balls/holes on the plates respectively. The essential measurands of the two dimensional standards are the coordinates of the feature points, however, the measurement equivalences on them have not been verified. In this study, the authors propose the coordinates-based evaluation of the reference values and their uncertainty in two dimensional standard calibration comparison.     

Multi-class grasping classifiers using EEG data and a common spatial pattern filter

This paper describes the classification of various human actions from brain activity. In particular, we focus on grasping movements and estimate grasping patterns from electroencephalogram (EEG) data. EEG data is converted to grasping features by using a common spatial pattern filter (CSP filter), and the features are subsequently classified into grasping categories by using the k-nearest neighbor method. We tested the pipeline of feature extraction and classification on the EEG dataset. The EEG data were acquired while participants grasped an object according to the Cutkosky’s grasping taxonomy, in which grasping movements are categorized into nine power-type grasping patterns and seven precision-type grasping patterns. The best classification rate for 9-class power-type grasping patterns was 48% and for 7-class precision-type grasping patterns was 40%.     

Numerical Flow Simulation in Turbine Mode of Counter-Rotating Type Pumping Unit to Cooperate with Wind Turbine

This serial research has proposed the hybrid power system combined the wind power unit with the counter-rotating type pump-turbine unit, to provide the constant output for the grid system, even at the suddenly fluctuating/turbulent wind circumstance. In this paper, the tandem impellers prepared for the counter-rotating type pumping unit were operated at the turbine mode, and the performances and the flow conditions were investigated numerically with accompanying the experimental results. Even though providing the pumping unit for the turbine mode, the maximum hydraulic efficiency is close to one of the counter-rotating type hydroelectric unit designed exclusively for the turbine mode. Besides, the runners/impellers of the unit work evidently so as to coincide the angular momentum change through the front runners/impellers with that through the rear runners/impellers, namely to take the axial flow at not only the inlet but also the outlet, without the guide vanes. From these results, it can be concluded that this type unit is effective to work at not only the pumping but also the turbine modes.