Sigma-delta modulators operating at a limit cycle

A new type of sigma-delta modulator that operates in a special mode named limit-cycle mode (LCM) is proposed. In this mode, most of the SDM building blocks operate at a frequency that is an integer fraction of the applied sampling frequency. That brings several very attractive advantages: a reduction of the required power consumption per converted bandwidth, an immunity to excessive loop delays and to digital-analog converter waveform asymmetry and a higher tolerance to clock imperfections. The LCMs are studied via a graphical application of the describing function theory. A second-order continuous time SDM with 5 MHz conversion bandwidth, 1 GHz sampling frequency and 125 MHz limit-cycle frequency is used as a test case for the evaluation of the performance of the proposed type of modulators. High level and transistor simulations are presented and compared with the traditional SDM designs.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

Recension des écrits sur l'impact des contacts sexuels précoces sur les hommes.

A review of the literature on the impact of sexual contacts between adults and boys reveals the existence of two principal outcomes: 1) some participants develop various disorders once in adulthood, such as behavioural problems, sexual disorders, or personality problems; 2) some participants do not present with any major disorders in the long run. These different outcomes may be associated with several moderating variables related to the sexual contacts, such as the level of coercion at the time of these contacts, the bond between the child and the adult, or the context of the sexual relation. However, the conclusions relating to the relations between early sexual contacts with adults and subsequent problems of adaptation in adulthood are difficult to determine. This is because of various methodological problems associated with relevant studies (i.e., definition of these contacts, nature of the sample, method evaluation, statistical analyses). In this article, we propose certain avenues of research that may help clarify this problem. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Influence of device engineering on the analog and RF performances of SOI MOSFETs

This work presents a systematic comparative study of the influence of various process options on the analog and RF properties of fully depleted (FD) silicon-on-insulator (SOI), partially depleted (PD) SOI, and bulk MOSFET's with gate lengths down to 0.08 /spl mu/m. We introduce the transconductance-over-drain current ratio and Early voltage as key figures of merits for the analog MOS performance and the gain and the transition and maximum frequencies for RF performances and link them to device engineering. Specifically, we investigate the effects of HALO implantation in FD, PD, and bulk devices, of film thickness in FD, of substrate doping in SOI, and of nonstandard channel engineering (i.e., asymmetric Graded-channel MOSFETs and gate-body contacted DTMOS).     

Desalination by distillation and by reverse osmosis — trends towards the future

As the requirement for fresh water increases worldwide, there is a need for more and more plants that are able to treat non-conventional water sources. Sea water has become an important source of fresh water in many arid regions. This feature provides an overview of recent process improvements in sea water desalination using reverse osmosis, multi-stage flash, multi-effect distillation and electrodialysis. Areas discussed include the use of alternative energy sources (wind energy, solar energy and nuclear energy) for reverse osmosis or distillation processes, and the impact of the different desalination process on the environment. Also covered are the implementation of hybrid processes in sea water desalination, and the pretreatment of desalination plants by pressure-driven membrane processes.     

Bio-layer management in anaerobic membrane bioreactors for wastewater treatment.

Membrane separation technology represents an alternative way to achieve biomass retention in anaerobic bioreactors for wastewater treatment. Due to high biomass concentrations of anaerobic reactors, cake formation is likely to represent a major cause of flux decline. In the presented research, experiments are performed on the effect of biomass concentration and level of gas sparging on the hydraulic capacity of a submerged anaerobic membrane bioreactor. Both parameters significantly affected the hydraulic capacity, with biomass exerting the most pronounced effect. After 50 days of continuous operation the critical flux remained virtually unchanged, despite an increase in membrane resistance, suggesting that biomass characteristics and hydraulic conditions determine the bio-layer formation rather than the membrane's fouling level. The concept of bio-layer management is introduced to describe the programmed combination of actions performed in order to control the formation of biomass layer over membranes.     

Role of Perceived Importance in Intergroup Contact.

Furthering G. W. Allport's (1954) contentions for optimal contact, the authors introduce a new construct: the perceived importance of contact. They propose that perceived importance is the best proximal predictor of contact's reduction of prejudice. If individuals have opportunities for contact at work or in the neighborhood, their chances to have intergroup acquaintances and friends increase. Intergroup contact among acquaintances and friends can be perceived as more or less important, which in turn determines intergroup evaluations. A 1st study shows that the new measure of perceived importance is indeed distinct from established quantity and quality indicators. The results are cross-validated in a 2nd study that also sheds light on the meaning of importance. In 3rd and 4th studies, structural equation analyses and a meta-analysis support the hypotheses. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Synchronous Full-Scan for Asynchronous Handshake Circuits

Handshake circuits form a special class of asynchronous circuits that has enabled the industrial exploitation of the asynchronous potential such as low power, low electromagnetic emission, and increased cryptographic security. In this paper we present a test solution for handshake circuits that brings synchronous test-quality to asynchronous circuits. We add a synchronous mode of operation to handshake circuits that allows full controllability and observability during test. This technique is demonstrated on some industrial examples and gives over 99% stuck-at fault coverage, using test-pattern generators developed for synchronous circuits. The paper describes how such a full-scan mode can be achieved, including an approach to minimize the number of dummy latches in case latches are used in the data path of the handshake circuit.     

The measurement of the diffusion coefficient and the sorption isotherm of water in paint films

An experimental technique together with a numerical model is proposed with which the diffusion coefficient and the sorption isotherm of water in paint can be measured. Inside a closed vessel, paint films are on stainless-steel plates. Water is present as water vapour in the air and in the paint. After blowing dry or wet air through the vessel for some time, the situation moves to a new equilibrium. The relative humidity of the air inside the vessel is measured as a function of time. From fitting the theoretical/numerical model against the experimental values, follow the diffusion coefficient and the sorption isotherm of water in the paint. The results show large scattering. When the independently measured sorption isotherm is used as an input parameter in the model, the fitting procedure gives much smaller scattering for the diffusion coefficient.