Methanation of CO2 with the oxygen-deficient Ni(II)-ferrite under dynamic conditions

The continuous methanation of CO₂ has been accomplished over hydrogen-reduced Ni(II)-bearing ferrite (Ni_xFe_3–xO_4–; x=0.39, > 0) in a mixed gas flow of CO₂ and H₂ at 250–375 °C. The yield and the selectivity for the methanation were larger than 50% and 95%, respectively, at the initial stage of the process. They decreased to 31% and 89%, respectively, after 6 h methanation. The innovative results can be ascribed to the use of the new material; hydrogen-reduced Ni(II)-bearing ferrite. Its formation was evinced by chemical analyses and the increase in the lattice constant; the lattice constant of the Ni(II)-bearing ferrite (a₀ 0.8375 nm) was enlarged to 0.8379 nm by hydrogen reduction. The enlarged lattice constant was not changed during the methanation. These findings suggest that the methanation occurs at the oxygen-deficient site of the hydrogen-reduced Ni(II)-bearing ferrite, as well as the formation of water by combination of the incorporated oxygens with hydrogen. The methanation consists of three steps of the elementary reaction. First, the oxygen-deficient sites are formed by hydrogen reduction; second, CO₂ is reduced to elementary carbon and two oxygen ions which are incorporated into the oxygen-deficient sites; and third, the carbon deposited on the surface of the reduced ferrite is selectively hydrogenated to CH₄.     

Disposition of diadenosine 5',5"'-P1,P4-tetraphosphate (Ap4A) in rats

The disposition of diadenosine 5'5"'-P1,P4-tetraphosphate (Ap4A), an endogenous dinucleotide, was investigated in rats. The degradation of Ap4A in rat plasma was very rapid and could be explained by a Michaelis-Menten equation: Km and Vmax values were 1.69 micrograms/ml and 4.32 micrograms/min/ml, respectively. Ap4A was degraded in rat plasma to ATP and AMP, but not to 2 ADP molecules, and these nucleotides were further degraded through adenosine. The degradations kinetics were examined. After intravenous bolus injection, Ap4A in plasma declined rapidly and the rate of elimination was dose-dependent: the biological half-life was about 3s at the dose of 1 mg/kg and was longer at 3 mg/kg. When Ap4A was administered by intravenous infusion (0.5 or 1.0 mg/kg/min), the plasma level rapidly reached a steady-state, which then rapidly declined after stopping the infusion.     

Active sensing control improving SLAM accuracy for a vehicle robot

Artificial Life and Robotics - This study considers an autonomous mobile vehicle using SLAM technology in an unknown environment. The focused problem is the decrease of trajectory following...     

Synchronization of pulsed Tksapphire lasers and its application to difference frequency mixing for tunable infrared generation

A simple and effective technique for synchronizing two independent Ti: sapphire lasers was developed and used for difference-frequency generation. By control of pump intensity, buildup times of these lasers were adjusted to coincide for any combination of wavelengths that was needed for the production of a desired difference frequency. Synchronized pulses were mixed at a AgGaS(2) crystal, producing infrared pulses from 6.2 to 9.7 μm. Characteristic features of the method as well as its possible extension of the tuning range are discussed.     

Generation of uniform drops via through-hole arrays micromachined in stainless-steel plates

This study investigated the generation of oil drops using new symmetric and asymmetric through-hole-array devices made of stainless steel. The through-hole-array devices were built by piling up six stainless-steel plates, each having circular micro-holes with a diameter of 300 or 500 μm or micro-slots with a shorter line of 300 or 500 μm. Drops were generated by injecting a dispersed phase (refined soybean oil) via the through-hole array into a compartment filled with a continuous phase (Milli-Q water solution containing one of two emulsifiers). The drop detachment from symmetric and asymmetric through holes was observed in real time and analyzed. Uniform oil drops with average diameters of 1.0–4.1 mm and coefficients of variation of typically less than 6% were generated using symmetric and asymmetric through-hole-array devices. The resultant drop diameters for asymmetric through-hole arrays were significantly smaller than those for symmetric through-hole arrays. This paper also discusses experimental results regarding the effects of the microstructure, the dimensions of the through holes, and the type of emulsifier on drop generation and the resultant drop diameter.     

Straight-through microchannel devices for generating monodisperse emulsion droplets several microns in size

The authors recently proposed a promising technique for producing monodisperse emulsions using a straight-through microchannel (MC) device composed of an array of microfabricated oblong holes. This research developed new straight-through MC devices with tens of thousands of oblong channels of several microns in size on a silicon-on-insulator plate, and investigated the emulsification characteristics using the microfabricated straight-through MC devices. Monodisperse oil-in-water (O/W) and W/O emulsions with average droplet diameters of 4.4–9.8 μm and coefficients of variation of less than 6% were stably produced using surface-treated straight-through MC devices that included uniformly sized oblong channels with equivalent diameters of 1.7–5.4 μm. The droplet size of the resultant emulsions depended greatly on the size of the preceding oblong channels. The emulsification process using the straight-through MC devices developed in this research had very high apparent energy efficiencies of 47–60%, defined as (actual energy input applied to droplet generation/theoretical minimum energy input necessary for making droplets) × 100. Straight-through MC devices with numerous oblong microfluidic channels also have great potential for increasing the productivity of monodisperse fine emulsions.     

Inside Front Cover: Fabrication of Ideally Ordered Nanoporous Alumina Films and Integrated Alumina Nanotubule Arrays by High‐Field Anodization (Adv. Mater. 17/2005)

A simple, low‐cost approach to fabricating large‐area highly ordered nanoporous alumina films in sulfuric acid solutions through a single‐step high‐field anodization, without the assistance of any additional process, is reported on p. 2115 by Chu and co‐workers. The critical high anodizing potential in the adopted electrolyte system increases with the ageing of solutions after a long period of anodization. Correspondingly, the applicable current density for stable anodization rises significantly, thus leading to high‐speed film growth. Uniform porous anodic alumina films in sulfuric acid solutions under a high electric field of 40–70 V and 1600–2000 A m^–2 are achieved.