Hydrolytic aging of polypropylene studied by X‐ray photoelectron spectroscopy

X‐ray photoelectron spectroscopy (XPS) was used to study the hydrolytic aging of polypropylene according to the pHs of degrading buffer solutions and the time of aging. The study was concentrated over periods of 3, 6, and 9 months for values of pH close to the real environments of use of the material (pH of 6, 7, and 8). The polypropylene underwent an oxidation of its polymeric matrix, independently of the range of pH values, by the production of C? OH, C?O, and O?C? O groups. These chemical functions were observed in high resolution XPS spectra around C1s and O1s peaks. Beginning with these results and from mechanisms of (photochemical, thermal, and others) aging proposed in the literature, it was then possible to propose mechanisms of hydrolytic ageing of polypropylene. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3830–3838, 2004     

Anisotropy in mechanical and dynamic properties of composites based on carbon fiber filled thermoplastic elastomeric blends of natural rubber and high density polyethylene

The effects of short carbon fibers on static and dynamic properties of thermoplastic elastomeric blends of natural rubber (NR) and high density polyethylene (HDPE) have been studied. Both mechanical and dynamic properties are dependent on fiber concentration. The fiber aspect ratio ranges from 20 to 30. Adhesion between fiber and matrix is evident from the SEM photomicrographs of the failed composites and from variation of relative damping properties. Fiber orientation occurring during processing causes anisotropy in the physical properties. In composites with longitudinally oriented fibers, tensile failure occurs by both fiber pullout and breakage, while in composites with transversely oriented fibers, matrix failure dominates. The incorporation of fibers into the matrix lowers the tan δ_max value, but no change in glass transition temperature is observed.     

Phenolic compounds from vacuum pyrolysis of wood wastes

Various softwood and hardwood bark residues, primary sludges and softwood sawdust residues were processed by vacuum pyrolysis in a laboratory scale batch reactor. The pyrolysis oil, water, charcoal, and gas were recovered and analyzed. The pyrolysis oils were analyzed in details for their content in phenolic compounds after derivatization to their acetyl derivatives. The influence of temperature, heating rate, feedstock bed thickness, particle size and feedstock water pretreatment on the yield of phenols was investigated. The highest yield of phenols was obtained when hardwood bark was soaked in water for 48 hours and pyrolyzed at a temperature of 450°C and a heating rate of 10°C/min. Pyrolysis performance was evaluated in terms of total phenolic yield and composition.     

Prediction of minimum velocity and minimum bed pressure drop for gas-solid fluidization in conical conduits

Experimental investigations have been carried out for spherical and non-spherical particles using beds comprised of single-sized particles and mixtures in the size and particle density ranges of 439 to 1524 μm and 1303 to 4948 kg/m³, respectively. Five conical fluidizers with varying apex angles of 8.86, 14.77, 19.60, 32.0 and 43.2 degrees were used. Experimental values of minimum velocity and bed pressure drop with air as the fluidizing medium have been compared with their respective values obtained from different models available in the literature. Deviations for each chosen model have been presented.     

Influence of mixing cycle on the degree of mixing of calcite‐filled polyethylene upon stretching

The mixing cycle‐dependent degree of dispersion and degree of mixing of a calcite (calcium carbonate) agglomerate in high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), and linear low‐density polyethylene (LLDPE) matrices upon stretching was investigated using three different techniques: mechanical property, morphological behavior, and image analyzer analyses. The mechanical properties analyzed in terms of the tensile strength and maximum elongation resulted in that the second mixing was the best for giving a better property for all systems except the LDPE system, which exhibited no significant difference between the second and third mixings. The morphological behavior of the three compounds were different, but no distinctive difference was observed to differentiate the degree of mixing from system to system. The number‐, weight‐, and z + 1‐average diameters of the air hole and the aspect ratio upon the stretching and mixing cycle were calculated to analyze the degree of mixing of the calcite‐filled composites. As a consequence, no difference in the average diameter of the air hole was obtained among the three systems, but the aspect ratios of the air hole varied significantly. Thus, the degree of dispersion and the degree of mixing may be influenced by the average calcite agglomerate size, the average diameter of the air hole, and the aspect ratio upon stretching and mixing cycles. Those factors would be formed by the difference in chemical characteristics upon various microstructures of polyethylene and its molecular weight and molecular weight distribution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 311–321, 2003     

Polyurethane‐infiltrated carbon foams: A coupling of thermal and mechanical properties

The thermal and mechanical properties of polyurethane‐infiltrated carbon foam of various densities were investigated. By combining the high thermal conductivity of the carbon foam with the mechanical toughness of the pure polyurethane, a mechanically tough composite (relative to the unfilled foam) that could be used at higher temperatures than the polyurethane's degradation was formed. Both the tensile strength and the modulus increased by an order of magnitude for the composites compared to unfilled foam, while the compressive and shear strengths and moduli of the composites approached values exhibited by pure polyurethane. At both 300 and 400°C, the rectangular blocks of pure polyurethane lost their mechanical integrity due to decomposition in air. Thermogravimetric analysis confirms substantial initial weight loss above 290°C. Filled carbon foam blocks, however, maintain their mechanical integrity at both 300 and 400°C indefinitely, although the bulk of the rectangular block mass is polyurethane. Three different carbon foam densities are examined. As expected, the higher density foams show greater heat transfer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2348–2355, 2003     

CO2 gasification of wood charcoals derived from vacuum and atmospheric pyrolysis

The gasification of biomass derived char obtained via vacuum and atmospheric pyrolysis of Populus tremuloides has been studied in the ranges of 725–960°C and 0.1 to 6 MPa. CO₂ was used as the oxidizing gas. The results show that char reactivity is influenced by the preheating rates and that pressure effects are significant between 850°C and 950°C. A correlation based on the expression: df/dt = k₀{exp(-E/RT)}(1 - f)^af^βP^yCO₂ was used to fit the experimental data. In general, vacuum pyrolysis derived char showed a higher reactivity than atmospheric pyrolysis chars. An explanation based on a higher oxygen content of the vacuum pyrolysis char is suggested.     

Prediction of dispersed phase holdup in a modified multi‐stage bubble column scrubber

This paper reports on the experimental investigation carried out to evaluate fractional dispersed phase holdup for a gas‐liquid mixture in a modified multi‐stage bubble column (with contraction and expansion disks), which has been conceived, designed and fabricated as a wet scrubber for control of air pollution; in addition it has versatile use as a gas‐liquid contactor in chemical process industries. A correlation developed for predicting fractional dispersed phase holdup has been found to be encouraging and highly significant from statistical analysis.     

Plasma and lipoprotein fatty acid composition in glycogen storage disease type I

Nocturnal intragastric feeding has been shown to be an effective means to improve clinical and biochemical features in glycogen storage disease type I (GSD-I). In this study, we investigated the fatty acid patterns in a whole plasma and in circulating lipoproteins in patients on this therapy. The results demonstrated massive concentration of total fatty acids coupled with higher levels of triglycerides, free cholesterol, cholesterol ester and phospholipids. This hyperlipidemia involved all fatty acids without distinction of carbon or bond numbers. However, the increase was more pronounced for saturated than polyunsaturated fatty acids, as was demonstrated by the ratios of both oleic acid to linoleic acid (1.91±0.40 vs 0.80±0.09 in controls) and of ω3+ω6 to ω9 fatty acid families (0.92±0.11 vs 1.66±0.08 in controls). The fatty acid patterns in very low (VLDL), low (LDL) and high (HDL) density lipoprotein showed substantial differences in composition, reflecting an association between an abnormal lipoprotein pattern and essential fatty acid deficiency. Furthermore, GSD-I patients exhibited a significant increase in VLDL (17±2 vs 47±7 mg/dl) and LDL cholesterol (124±7 vs 206±24 mg/dl), coupled with a decrease in HDL cholesterol (49±4 vs 28±3 mg/dl). These data documenting high LDL cholesterol and low HDL cholesterol associated with an increased concentration and proportion of saturated fatty acids suggest that GSD-I patients on nocturnal intragastric feeding are at high risk for atherosclerosis and its complications.     

Solvent Crystallization of the Fat and Fatty Acids of Schleichera trijuga Seed

The crystallizations of the kusum oil and the mixed fatty acids thereof were studied from several solvents at various temperatures (+10° C to ?60° C). The results indicate in general that in the range of temperatures studied, petroleum ether as a single solvent is comparable in efficiency to methanol and superior to both acetone and ethanol in respect of separation of the saturated and unsaturated components of the fatty acid mixture. The saturated and unsaturated fractions of the oil also are better separated by petroleum ether than acetone. Further, oleic acid essentially free from linoleic acid is obtainable by a preliminary crystallization of the fatty acid mixture from petroleum ether at ca. ?12° C, followed by two additional crystallizations from acetone at ca. ?55° C.