Development of the Base Station Controller and Manager in the CDMA Mobile System

The base station (BS) in the CDMA Mobile System (CMS) connects calls through the radio interface and is designed to provide mobile subscribers with high quality service in spite of mobile subscribers’ motions. The BS consists of multiple base station transceiver subsystems (BTSs), a base station controller (BSC) and a base station manager (BSM). This paper is concerned with the BSC and the BSM. The BSC is located between the BTSs and the mobile switching center (MSC) connected with the public network, and is responsible for controlling mobile calls from and to mobile subscribers via the BTSs. The BSM provides operator-interfaces per the BS and takes responsibility of operation and maintenance (OAM) of the BS. Design of the BSC is based on two module types: functional module and unit module. The functional module is used to support new services easily and the unit module to increase the system capacity economically. Both modular types are easily achieved by inserting the corresponding modules to the system. Particularly, in order to efficiently support the soft handover which is one of CDMA superior advantages, the BSC adopts a large high-speed packet switch connecting up to 512 BTSs, and thus mobile subscribers can be provided with soft handover in high probability. The BSM is based on a commercial workstation to support OAM functions efficiently and guarantee high reliability of the functions. The BSM uses graphical user interface (GUI) for efficient OAM functions of the BS.     

An efficient assumed strain element model with six DOF per node for geometrically non-linear shells

The present paper describes an assumed strain finite element model with six degrees of freedom per node designed for geometrically non-linear shell analysis. An important feature of the present paper is the discussion on the spurious kinematic modes and the assumed strain field in the geometrically non-linear setting. The kinematics of deformation is described by using vector components in contrast to the conventional formulation which requires the use of trigonometric functions of rotational angles. Accordingly, converged solutions can be obtained for load or displacement increments that are much larger than possible with the conventional formulation with rotational angles. In addition, a detailed study of the spurious kinematic modes and the choice of assumed strain field reveals that the same assumed strain field can be used for both geometrically linear and non-linear cases to alleviate element locking while maintaining kinematic stability. It is strongly recommended that the element models, described in the present paper, be used instead of the conventional shell element models that employ rotational angles.     

The design of robots and intelligent manipulators using modern composite materials

The operating speed and endpoint positional accuracy of existing industrial manipulators are limited by the inertial and stiffness characteristics of the articulating members of the robot's mechanical linkage. This limitation may be overcome by developing members having high structural stiffness and strength with low mass, and this has been recognized for some time. These characteristics can be obtained by fabricating the moving members of manipulators in fiber reinforced composite materials. In order to establish a basis for the dynamic analysis of robots fabricated in viscoelastic composites, a variational theorem is developed herein. A preliminary comparative study is then undertaken for manipulators manufactured in a graphite-epoxy composite material and also steel in order to demonstrate some of the advantages to be accrued from this proposed new design philosophy.     

Application of differential quadrature to static analysis of structural components

The numerical technique of differential quadrature for the solution of linear and non-linear partial differential equations, first introduced by Bellman and his associates, is applied to the equations governing the deflection and buckling behaviour of one- and two-dimensional structural components. Separate transformations are used for higher-order derivatives, as suggested by Mingle, thus extending the method to treat fourth-order equations and to include multiple, boundary conditions in the respective co-ordinate directions. Results are obtained for various boundary and loading conditions and are compared with existing exact and numerical solutions by other methods. The application of differential quadrature to this class of problems is seen to lead to accurate results with relatively small computational effort.     

Effect of bulk flow pulsations on film cooling with compound angle holes

Experiments are conducted to investigate the effects of bulk flow pulsations on film cooling with compound angle holes. A row of five film cooling holes is considered with orientation angles of 0°, 30°, 60°, and 90° at a fixed inclination angle of 35°. Static pressure pulsations are produced by an array of six rotating shutter blades, which extend across the span of the exit of the wind tunnel test section. The pulsation frequency is fixed at 36 Hz, but changes in the time-averaged blowing ratios of 0.5, 1.0 and 2.0 produce three different coolant Strouhal numbers, 3.6, 1.8 and 0.9, respectively. Detailed film cooled boundary layer temperature distributions are measured by a cold wire and the adiabatic film cooling effectiveness by thermochromic liquid crystal (TLC). The boundary layer temperature surveys show that pulsations induce large disruptions to the boundary layer temperature distribution and the film coverage. As the orientation angle increases, the injectant concentration spreads further into the spanwise direction because of pulsations than the steady case. With pulsations the adiabatic film cooling effectiveness value decreases regardless of the orientation angle. The amount of reduction, however, depends on the orientation angle in such a way that the larger the orientation angle is, the smaller the reduction is.     

A lagrangian model for spray dryer desulfurization system

The purpose of this work is to develop a reliable numerical model for the spray dryer desulfurization system. The shape of the spray dryer requires that a body fitted orthogonal coordinate system be used for the numerical model. The governing equations are developed in the general orthogonal coordinates and discretized to yield a system of algbraic equations. A modified two-equation turbulence model is also included in the numerical program. The stability of QUICK scheme is investigated and the Absolutely Stable QUICK scheme is developed and included in the numerical model. The trajectory approach is used to simulate the flow of the dispersed phase. Two-way coupling phenomena is modeled by this sheme. The absorption of sulfur dioxide into lime slurry droplets is simulated by a model based on gas-phase mass transfer. The program is applied to a typical spray dryer desulfurization system. The reuslts show the capability of the program to predict the sensitivity of system performance to change in operational parameters.     

Classification and prediction of the critical heat flux using fuzzy theory and artificial neural networks

A new method to predict the critical heat flux (CHF) is proposed, based on the fuzzy clustering and artificial neural network. The fuzzy clustering classifies the experimental CHF data into a few data clusters (data groups) according to the data characteristics. After classification of the experimental data, the characteristics of the resulting clusters are discussed with emphasis on the distribution of the experimental conditions and physical mechanism. The CHF data in each group are trained in an artificial neural network to predict the CHF. The artificial neural network adjusts the weight so as to minimize the prediction error within the corresponding cluster. Application of the proposed method to the KAIST CHF data bank shows good prediction capability of the CHF, better than other existing methods.     

Ubiquitous Information Services with JAIN Platform

To provide responsive information services in a ubiquitous computing environment, service software and system development are indispensable. A component-based ubiquitous information system with a JAIN (Java APIs for Integrated Networks) platform to achieve seamless transmissions and reach-everywhere communications was designed in our research. In this development, numerous ubiquitous service modules were identified: location management, roaming, mobile IP and WAP networking. These component-based network modules were constructed using a component composition language with component specification and interface definition, running on top of a distributed service architecture using a JAIN platform to distribute the ubiquitous information services to mobile users. Two applications, Wireless-Application-Protocol (WAP) Mail and Video-on-Demand (VoD) services, show that the JAIN-like platform with the developed networking components effectively fills the gap for application developers between mobile appliances and various kinds of ubiquitous information services.