Feasibility of recycled newspaper as cellulose source for regenerated cellulose membrane fabrication

An environmental friendly regenerated cellulose membrane (RCM) was successfully prepared via NaOH/urea aqueous solution system by utilizing recycled newspaper (RNP) as the cellulose source. The morphological and chemical structure of resulting membrane were characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD) spectroscopy, and thermogravimetric analysis (TGA). Results from FTIR and XRD verified that the transparent RCM possesses cellulose II structure. SEM observation revealed that the transparent RCM consist of homogeneous dense symmetric membrane structure and composed of a skin layer with mean roughness parameter R_a, obtained from AFM analysis of 29.53 nm. Pure water flux, water content, water contact angle, porosity, and pore size of the resulting membrane were also measured. This study promotes the potential of the cellulose‐based membrane obtained from low cost cellulose source for application in filtration and separation system. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42684.     

Augmented reality assisted facility layout digitization and planning

Journal of Mechanical Science and Technology - Facility layout planning (FLP) has an important role in manufacturing industries. There are few approaches to solve FLP such as procedural,...     

Investigation on the effect of spinning conditions on the properties of hollow fiber membrane for hemodialysis application

Polyethersulfone (PES) hollow fiber membranes were fabricated via the dry‐wet phase inversion spinning technique, aiming to produce an asymmetric, micro porous ultrafiltration hollow‐fiber specifically for hemodialysis membrane. The objective of this study is to investigate the effect of spinning conditions on the morphological and permeation properties of the fabricated membrane. Among the parameters that were studied in this work are air gap distance, dope extrusion rate, bore fluid flow rate, and the take‐up speed. The contact angle was measured to determine the hydrophilicity of the fibers. Membrane with sufficient hydrophilicity properties is desired for hemodialysis application to avoid fouling and increase its biocompatibility. The influences of the hollow fiber's morphology (i.e., diameter and wall thickness) on the performance of the membranes were evaluated by pure water flux and BSA rejection. The experimental results showed that the dope extrusion rate to bore fluid flow rate ratio should be maintained at 1:1 ratio to produce a perfectly rounded asymmetric hollow fiber membrane. Moreover, the flux of the hollow fiber spun at higher air gap distance had better flux than the one spun at lower air gap distance. Furthermore, spinning asymmetric hollow fiber membranes at high air gap distance helps to produce a thin and porous skin layer, leading to a better flux but a relatively low percentage of rejection for BSA separation. Findings from this study would serve as primary data which will be a useful guide for fabricating a high performance hemodialysis hollow fiber membrane. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43633.     

Highly sensitive and selective dopamine detection by an amperometric biosensor based on tyrosinase/MWNT/GCE

Dopamine (3,4-dihydroxylphenyl ethylamine) is the most significant neurotransmitter in the human nervous system. Abnormal dopamine levels cause fatal neurological disorders, and thus measuring dopamine level in actual samples is important. Although electrochemical methods have been developed for detecting dopamine with high accuracy, certain substances (e.g., ascorbic acid) in actual samples often interfere with electrochemical dopamine detection. We developed tyrosinase-based dopamine biosensor with high sensitivity and selectivity. An electrochemically pretreated tyrosinase/multi-walled carbon nanotube-modified glassy carbon electrode (tyrosinase/MWNT/GCE) was prepared as an amperometric biosensor for selective dopamine detection. For optimizing the biosensor performance, pH, temperature, and scan rate were investigated. The electrochemically pretreated tyrosinase/MWNT/GCE exhibited not only the highest sensitivity (1,323 mAM^?1 cm^?2) compared to previously reported tyrosinase-based dopamine sensors, but also good long-term stability, retaining 90% of initial activity after 30 days. Additionally, ascorbic acid, a major interfering substances, was not oxidized at the potential used to detect dopamine oxidation, and the interfering effect of 4mM ascorbic acid was negligible when monitoring 1mM dopamine. Consequently, the electrochemically pretreated tyrosinase/MWNT/GCE is applicable for highly selective and sensitive dopamine detection in actual samples including interfering substances, thereby extending the practical use to monitor and diagnose neurological disorders.     

Vibration of antisymmetric angle-ply composite annular plates of variable thickness

Journal of Mechanical Science and Technology - Based on first order shear deformation theory, free vibrational behaviour of antisymmetric angle-ply composite annular plate is investigated. The...     

Raft crystals of poly(isoprene)-block-poly(ferrocenyldimethylsilane) and their surface wetting behavior during melting as observed by AFM and NanoTA

We report on the morphology evolution during heating and melting of lamellar poly(isoprene)-block-poly(ferrocenyldimethylsilane) (PI₇₆-b-PFDMS₇₆) raft crystals deposited at the native oxide surface of silicon (SiO₂) or at a highly ordered pyrolytic graphite (HOPG) surface, studied by in situ temperature controlled atomic force microscopy. Crystals deposited on hydrophilic SiO₂ surfaces revealed an irreversible decrease in length at temperatures of up to tens of degrees above their expected melting temperature, while maintaining their platelet-like structure. Crystals deposited on hydrophobic HOPG surfaces initially decreased in length below their expected melting temperature, while at 120 °C and above a typical molten morphology was observed. In addition, the irreversible formation of a PI₇₆-b-PFDMS₇₆ wetting layer around the crystals was observed upon increasing the temperature. These observations in the morphological behavior upon heating emphasize the role of interfacial energy between a surface deposited block copolymer based macromolecular nanostructure and its supporting substrate.     

Effects of additives on oxidation characteristics of palm oil‐based trimethylolpropane ester in hydraulics applications

Hydraulic fluids represent one of the most important groups of industrial lubricants. Increasing attention to environmental issues drives the lubricant industry to choose vegetable‐based hydraulic fluids which are biodegradable as compared to mineral‐based fluids. However, the lubricating properties of vegetable oil, such as poor oxidative stability and high pour point, have hindered their use. In this study, trimethylolpropane ester, which was derived from palm‐based methyl ester, was used as the base hydraulic fluid. The purpose of the study was to determine the optimum formulation for palm oil‐based synthetic lubricants by using suitable additives that can improve the oxidative stability and viscosity in accordance with the standard regulations for hydraulic fluid applications. The oxidative stability of the oil was evaluated by total acid number (TAN) and viscosity tests. In general, base oil without additive began to degrade after 200 h. The formulated oil, on the other hand, was quite stable even after 800 h of operation. The best formulation was obtained using 1.0% of either additive A or additive B. Both TAN and viscosity values were found to increase with increasing heating temperature. Meanwhile, the results have also shown that additive A performs better than additive B. After 800 h of exposure, the final TAN value for the formulated oil was only at 0.32 as compared to 4.88 mg KOH/g for the oil without additive. However, the kinematic viscosity of the oil at 40 and 100 °C was almost unchanged as compared to the oil without additive.     

Reinforcement of graphene nanoplatelets on plasticized poly(lactic acid) nanocomposites: Mechanical,thermal, morphology,and antibacterial properties

Plasticized poly(lactic acid) (PLA)‐based nanocomposites filled with graphene nanoplatelets (xGnP) and containing poly(ethylene glycol) (PEG) and epoxidized palm oil (EPO) with ratio 2 : 1 (2P : 1E) as hybrid plasticizer were prepared by melt blending method. The key objective is to take advantage of plasticization to increase the material ductility while preserving valuable stiffness, strength, and toughness via addition of xGnP. The tensile modulus of PLA/2P : 1E/0.1 wt % xGnP was substantially improved (30%) with strength and elasticity maintained, as compared to plasticized PLA. TGA analysis revealed that the xGnP was capable of acting as barrier to reduce thermal diffusion across the plasticized PLA matrix, and thus enhanced thermal stability of the plasticized PLA. Incorporation of xGnP also enhanced antimicrobial activity of nanocomposites toward Escherichia coli, Salmonella typhimurium, Staphylococcus aureus, and Listeria monocytogenes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41652.     

The effect of magnetic and optic field in water electrolysis

Hydrogen production via water electrolysis was studied under the effect of magnetic and optical field. A diode solid state laser at blue, green and red were utilized as optical field source. Magnetic bar was employed as external magnetic field. The green laser has shown a greatest effect in hydrogen production due to its non-absorbance properties in the water. Thus its intensity of electrical field is high enough to dissociation of hydronium and hydroxide ions during orientation toward polarization of water. The potential to break the autoprotolysis and generate the auto-ionization is the mechanism of optical field to reveal the hydrogen production in water electrolysis. The magnetic field effect is more dominant to enhance the hydrogen production. The diamagnetic property of water has repelled the present of magnetic in water. Consequently the water splitting occurs due to the repulsive force induced by the external magnetic field. The magnetic distributed more homogenous in the water to involve more density of water molecule. As a result hydrogen production due to magnetic field is higher in comparison to optical field. However the combination both fields have generated superior effect whereby the hydrogen yields nine times higher in comparison to conventional water electrolysis.