Performance analysis of disk allocation method usingerror-correcting codes

The problem of distributing a Cartesian product file on multiple disks to maximize the parallelism for partial match queries is addressed. C. Faloutsos et al. (1989) have proposed an allocation method for Cartesian product files on multiple disks by using linear error-correcting codes. The performance of the allocation method is analyzed. Some conditions under which the allocation method is strictly optimal for queries with a given number of unspecified attributes are presented. A necessary and sufficient condition for a linear code to give a strictly optimal allocation method is discussed. Formulas for the average response time on queries with w unspecified attributes, denoted T_w, in terms of the weight distribution of the code or its dual code, and formulas for the average response time Ton all queries, are given. Several examples whose average response times T_w or T are close to theoretical lower bounds are presented     

Construction and field measurement of high-speed railway test embankment built on Indian expansive soil “Black Cotton Soil”

The railway embankment applied to high-speed railways is required to have high performance in terms of strength and deformation characteristics. Especially in the case of railway embankments that support slab tracks, the allowable settlement is very small. There are two technical challenges in constructing high-speed rail embankments to support slab tracks in India. The first challenge is dealing with problematic black cotton soil (BCS), which is widely distributed in India but very unusual soil in Japan. The second challenge is posed by the strict deformation requirement in the construction of the embankments. In this study, a 6 m-high test embankment was constructed on BCS in India. The deformation of the embankment and changes in water content were measured over a period of 18 months. In the construction of the test embankment, two different BCS countermeasures were applied. The results of the tests on this embankment were compared with those from an embankment without countermeasures. Complicated deformation behaviors, including settlement and the uplift of embankment, were observed in the section without countermeasure. However, in the embankment with cement-mixed gravelly soil (CGS) slab improvement with geosynthetics, the much lower amplitude of embankment deformation is evidence of the effectiveness of this countermeasure. The cohesive non-swelling soil (CNS) layer applied immediately below the embankment to reduce the water content fluctuation of BCS was not effective enough for use for high-speed railway embankment. Besides determining the technical challenges for the BCS countermeasures, the results of this study confirmed that a high-performance embankment can be constructed with Indian embankment material by performing sufficient compaction management.     

Development of lateral displacement sensor for real‐time detection of structural damage

We have developed a novel sensor that enables us to measure the relative story displacement of a building structure in real time. This lateral displacement sensor (LDS) is composed of a light‐emitting diode (LED) array, which is fixed on the ceiling, and a position‐sensitive detector (PSD) unit, which is placed on the floor. We optimized the LDS to achieve high accuracy in lateral displacement measurement. The accuracy was evaluated to be 60 µm by conducting shaking table tests. Two LDSs were implemented in an actual building equipped with an active variable stiffness (AVS) system, and the building was vibrated with seismic waveforms by an exciter placed on the rooftop. The seismic displacement of the second floor relative to the first floor was measured using the LDS. Furthermore, the inclination angle of the second floor could be measured using the LDS during the seismic vibration. Using the AVS system, we realized the residual displacement of the second floor without inducing damage to the building, and succeeded in real‐time residual displacement measurement for the first time. These results indicate that the LDS is useful for the health diagnosis of a building structure. © 2011 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Effects of phosphorus content on generation and growth of cracks in nickel–phosphorus platings owing to thermal cycling

We observed crack generation and structural changes in electroless nickel–phosphorus (Ni–P) plating layers formed on copper-metalized silicon nitride substrates both during thermal cycling from ? 40 to 250 °C and during storage (not cycling) at 250 °C in order to investigate the effect of the phosphorus contents on crack generation and growth in the Ni–P platings. The used platings contained phosphorus at three different contents: 2.1 wt% [Ni–P(low)], 6.5 wt% [Ni–P(med)], and 10.9 wt% [Ni–P(high)]. The generation time and the amount of cracks were strongly dependent on their phosphorus contents. More cracks appeared after thermal cycling than after storage at 250 °C. In Ni–P(low), cracks were generated after 200 thermal cycles, whereas no cracks were observed even after 250 h of storage at 250 °C. In Ni–P(med) and Ni–P(high), both during thermal cycling and storage at 250 °C, cracks formed during or after crystallization of the amorphous layers. These results suggest that the primary factors affecting the generation of cracks in electroless Ni–P platings are crystallization of the Ni–P platings and repeated changes in thermal stress.     

Lithium intercalation and alloying effects on electronic structures of spinel lithium manganese oxides

Employing the DV-Xα molecular orbital method, lithium intercalation effect and alloying effect have been investigated on the electronic structures of spinel M_xMn_2−xO₄ and LiM_xMn_2−xO₄ (M=Ti, V, Cr, Mn, Fe, Co, Ni and Cu). It is found that the lithium intercalation induces the electron transfer from Li to the surrounding O ions, and enlarges the Mn-3d/O-2p band gap greatly. Such a modification of the oxygen electronic state is probably related to the electrochemical cell voltage. This lithium intercalation effect still holds even in the alloyed systems. However, the amount of transferred charges from M to O ions changes depending on the alloying element, M. So the alloying addition modifies the oxygen electronic state and influences the lithium intercalation process indirectly.     

Combination of cytomegalovirus enhancer with human cellular promoters for gene-induced chondrogenesis of human bone marrow mesenchymal stem cells

High-expression plasmid vectors for human mesenchymal stem cells (MSCs) were constructed by combination of cytomegalovirus immediate-early enhancer with cellular promoters. MSCs transfected with the vector showed higher transgene production of a cytokine, which increased the differentiation level to chondrocytes.     

A quantitative analysis of a trace amount of hydrogen in high temperature heat-treated carbons

A technique to determine a trace amount of hydrogen in carbon materials heat-treated above 1000 °C was developed. Three types of carbons prepared from poly(furfulyl alcohol), poly(vinyl chloride) and mesophase carbon microbeads were heat-treated at various temperatures ranging from 1000 to 1800 °C. Then they were gasified by O₂ in a fixed bed flow reactor, and the H₂O gases formed during the gasification processes were carefully monitored with a Karl Fischer moisture analyzer. As a result, this method makes it possible to determine the hydrogen contents in the carbons down to three places of decimals as a weight percent and can detect even a trace amount of hydrogen as low as 0.002 wt.%. A possible chemical structure of carbon edge sites was also discussed based on the experimentally determined hydrogen contents.     

Proposal for a benchmark model of a laminated iron core and a large‐scale and highly accurate magnetic analysis

This paper describes a benchmark model proposed for the clarification of the characteristic of various methods for modeling the laminated iron core. In order to obtain a reference solution of the benchmark model, a large‐scale nonlinear magnetostatic field analysis with a mesh fine enough to represent the microscopic structure of the laminated iron core is carried out by using the hybrid finite element–boundary element (FE‐BE) method combined with the fast multipole method (FMM) based on diagonal forms for translation operators. The computational costs and accuracy of two kinds of homogenization methods are discussed, comparing them with the reference solution. As a consequence, it is verified that the homogenization methods can analyze magnetic fields in laminated iron core within acceptable computational costs. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 170(1): 26–35, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20809