High-pressure solubility of fullerene C60 in toluene

The solubility of fullerene C₆₀ in toluene was measured at temperatures between 278.2 and 308.2 K and pressures up to 340 MPa, and also at temperatures between 258.2 and 298.2 K under atmospheric pressure. The solubility increased with increasing pressure, and then decreased with a sharp maximum, suggesting a transition between solid phases. A thermodynamic analysis of the solubility supported the proposal of Korobov, et al. that the two solids correspond to C₆₀ (fcc) and C₆₀ · 2 (toluene) solvate. The solubility enhancement of C₆₀ by pressure in a low-pressure region is an unusual phenomenon when compared with the decrease in solubility of nonpolar molecular solids generally observed with rises in pressure.     

Chemical vapour deposition of Si3N4 from a gas mixture of Si2Cl6, NH3 and H2

Si₃N₄ layers were obtained on a quartz substrate from a gas mixture of Si₂Cl₆, NH₃ and H₂ under a reduced pressure in a temperature range of 800 to 1300‡ C. Amorphous Si₃N₄ layers that were dense and adherent to the substrate were obtained in a temperature range of 800 to 1100‡ C. On the other hand,α-Si₃N₄ layers were obtained at 1200‡ C and a source-gas ratio (N/Si) of 1.33 to 1.77. The lowest deposition temperature of amorphous Si₃N₄ was considered to be about 700‡ C. The microhardness of amorphous Si₃N₄ obtained in a temperature range of 800 to 1100‡ C was 2400 to 2600 kg mm⁻² (load: 50 g), and that ofα-Si₃N₄ obtained at 1200‡ C was 3400 kg mm⁻². Chlorine contents in the Si₃N₄ layer decreased with increasing deposition temperature and source-gas ratio (N/Si), and with decreasing total pressure.     

Microstructure Development and Dielectric Properties of Potassium Strontium Niobate Ceramics

Sintering of a KSr₂Nb₅O₁₅ powder compact at 1350°C resulted in a duplex structure. Prefiring of the compact between 1200° and 1300°C inhibited the abnormal grain growth responsible for the duplex structure. The Curie temperature and dielectric constant were dependent on the microstructure.     

Nanoparticle formation in H2O/N2 and H2O/Ar mixtures under irradiation by 20 MeV protons and positive corona discharge

To investigate the contribution of ions to gas nucleation, we have performed experiments on the formation of water droplets in H₂O/N₂ and H₂O/Ar gas mixtures by irradiation with a 20 MeV proton beam and by positive corona discharge. The size of the formed nanoparticles was measured using a differential mobility analyzer equipped with a Faraday cup electrometer. Using the proton beam, droplets around 10 nm in diameter were observed for both positively and negatively charged particles, but none were found when the corona discharge was used. This implies the importance of the presence of both positive and negative ions for the formation of nanosize droplets, which attract each other by Coulomb interactions, enhancing the collision frequency and leading to the formation of the 10 nm droplets.     

A neck‐in model in extrusion lamination process

In this study, the experiment of the extrusion lamination process using high‐pressure process low‐density polyethylene (LDPE) was performed. The nonisothermal viscoelastic simulation of the extrusion lamination experiment was also carried out. The simulation results were in good agreement with the experimental data within wide range of take up velocity and air gap length. We developed the theoretical model based on force balance and deformation type of a film to predict the neck‐in behavior in the extrusion lamination or cast film process. It was suggested from the neck‐in model that the neck‐in correlates with the ratio of planar to uniaxial elongational viscosity. It was confirmed that the neck‐in model could predict the film edge shape and neck‐in properly for conventional LDPE. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Enzymatic preparation of structured oils containing short-chain fatty acids

Structured oils prepared by enzymatic transacylation with triacylglycerols (TAGs) and various fatty acids (FAs) were characterized. Transacylation with trilaurin and saturated FAs (C4:0-C16:0) was performed using Lipozyme RM-IM under standard reaction conditions. The structured oils thus produced had transacylation ratios of 25-37%, as medium-chain FAs > long-chain FAs > short-chain FAs. This result confirmed that short-chain FAs have little reactivity in enzymatic transacylation. All prepared oils shared the same composition of TAG molecular species, as demonstrated by HPLC analysis, and contained a mixture of mono-substituted, di-substituted, and non-substituted TAGs. The reaction conditions for transacylation with TAGs and short-chain FAs were optimized to improve transacylation ratios. The introduction ratios of C4:0, C5:0, and C6:0 into trilaurin were increased to 52.4, 42.5, and 34.1%, respectively, by extending the reaction time. Transacylation between TAGs and short-chain FAs was further examined by using Lipase PL. C4:0 was introduced at 51.1%, the same ratio as for Lipozyme RM-IM. When C5:0 and C6:0 were used as the FA substrate, the transacylation ratios obtained were 47.7 and 43.4%, respectively, higher than those for Lipase RM-IM. Lipase PL is therefore useful for introducing short-chain FAs into TAGs.     

Molded micro- and mesoporous carbon/silica composite from rice husk and beet sugar

A molded carbon/silica composite with high micro- and mesoporosity, as well as a high bulk density, was fabricated by activating a disk-molded precursor made from carbonized rice husk (RH) and beet sugar (BS) at 875 °C in CO₂. The pore structure of the RH- and BS-based carbon/silica composite (RBC) was analysed in relation to the bulk density. An activation time of 2.0 h provided the largest BET specific surface area (1027 m²/g) and total pore volume (0.68 cm³/g) and a low bulk density (0.54 g/cm³). An RBC that was first activated for 1 h was immersed again in BS syrup and then activated in CO₂ for 1 h. This two-step activation process provided both a high bulk density (0.69 g/cm³) and a highly textured structure (BET specific surface area, 943 m²/g; total pore volume, 0.56 cm³/g). The immersion in BS syrup was useful for improving the texture without reducing the bulk density, in comparison to one-step activation for 1.0 h. The suspension of the RBCs was basic because of the residual inorganic compounds of potassium and calcium. However, the basicity of the suspension was alleviated by washing the RBCs with water.     

Microporous activated carbons from used coffee grounds for application to electric double‐layer capacitors

Electrochemical double‐layer capacitors (EDLCs) are devices that store enormous amounts of charge electrostatically when a potential is applied between electrodes of very high surface area (typically made of porous carbon) and an electrolyte. Wider commercialization of this technology has been held back by the lack of ultralow‐cost electrode materials. We demonstrate that used coffee grounds can be processed to form low‐cost electrodes. The surface and electrochemical characteristics of microporous activated carbons from used coffee grounds (CGCs) were measured. First, optimal times and temperatures for carbonization and activation were identified on the basis of Brunauer–Emmett–Teller (BET) surface area, pore volume, and pore size distribution. Second, CGCs were used as polarized electrodes in EDLCs, whose capacitances were evaluated using cyclic voltammetry. The results show that carbonization for 1 h at 600 °C with a heating rate of 300 °C/h, followed by CO₂ activation for 2 h at 1000 °C, affords the highest BET surface area (1867 m²/g) compared to other works. The produced CGCs have many micropores of less than 2 nm across, which contribute to the formation of an electric double layer. Capacitors made using these CGCs show the highest capacitance (103 F/g) in 0.8 M (C₂H₅)₄NBF₄/PC as an organic electrolyte, which is much higher than the ∼80 F/g typically used in organic‐electrolyte‐based commercial EDLCs, suggesting that coffee grounds are a useful electrode material. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Estimation of daily intake of phenols in hospital meal samples

Daily intakes of 12 phenols which are possible endocrine disruptors were estimated in hospital meals from 2000 to 2001. 4-Nonylphenol (4-NP (mix)) and bisphenol A (BPA) were detected at levels of 5.0 to 19.4 ng/g and 0.2 to 1.1 ng/g, respectively. 4-tert-Butylphenol, 4-n-pentylphenol, 4 -tert-pentylphenol, 4-n-hexylphenol, 4-n-heptylphenol and 4-tert-octylphenol were detected at levels of 0.1 to 2.4 microg/g. The daily intakes of 4-NP (mix) and BPA were 5.8 microg/day and 0.42 microg/day, respectively. The daily intakes of other phenols were less than 1 microg/day.     

Microstructure and Softening of Laser-Welded 960 MPa Grade High Strength Steel Joints

The microstructural evolution of laser-welded 960 MPa grade high strength steel joints and its effect on softening behavior of heat affected zone (HAZ) were investigated in this paper. The results show that microstructure of HAZ and fusion zone (FZ) is composed of lath martensite and bainitic ferrite. The microstructure of mixed grained zone presents strip-like characteristics and small block martensite distributes along the grain boundary. The grain size near the fusion line is about 25 μm, and the grain size in the fine grain zone is less than 5 μm. Microhardness of HAZ and FZ is lower than base metal. The soft zone locates in transitional region between tempering zone and mixed grained zone due to the interaction of the martensite tempering and the recovery and recrystallization of the rolled microstructure. Microhardness of soft zone is 310 HV and drops 18% compared to base material. Welding heat input has a remarkable effect on the width of soft zone and microhardness. The tensile properties of weld joints are closely related to the softening behavior of HAZ.