Effect of water pretreatment on CO<Subscript>2</Subscript> capture using a potassium-based solid sorbent in a bubbling fluidized bed reactor

A bubbling fluidized bed reactor was used to study CO₂ capture from flue gas by using a potassium-based solid sorbent, sorbKX35 which was manufactured by the Korea Electric Power Research Institute. A dry sorbent, sorbKX35, consists of K₂CO₃ for absorption and supporters for mechanical strength. To increase initial CO₂ removal, some amount of H₂O was absorbed in the sorbent before injecting simulated flue gas. It was possible to achieve 100% CO₂ removal for more than 10 minutes at 60°C and a residence time of 2 s with H₂O pretreatment. When H₂O pretreatment time was long enough to convert K₂CO₃ of sorbKX35 into K₂CO₃ · 1.5H₂O, CO₂ removal was excellent. The results obtained in this study can be used as basic data for designing and operating a large scale CO₂ capture process with two fluidized bed reactors. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Catalytic characteristics of various rubber-reinforcing carbon blacks in decomposition of methane for hydrogen production

Carbon black has recently been reported to act as an effective catalyst for methane decomposition and to exhibit stable catalytic behavior despite carbon deposition, and thus it can be used for CO₂-free production of hydrogen from natural gas. In this work, various carbon blacks with different primary particle size were investigated with respect to methane decomposition under atmospheric pressure from 1123 to 1223 K. Catalytic characteristics, such as activity, activation energy and reaction order, were investigated and compared. It was observed that with decreasing primary particle size (or increasing specific surface area), the specific activity increased and the activation energy decreased. The reaction orders for various pelletized, rubber-reinforcing carbon blacks were 0.6–0.7, about the same regardless of the primary particle size, while they were near 1 for fluffy carbon blacks. Fluffy carbon black showed higher activity and activation energy than the pelletized carbon black of the same primary particle size. Changes of the surface morphology during carbon deposition were observed by TEM. Variations of the number of active sites were discussed in regard of the primary particle size, carbon deposition and binder. The presence of different types of active sites was also suggested.     

Latent catalyst effects in halogen‐free epoxy molding compounds for semiconductor encapsulation

Latent catalyst effects were investigated to improve the physical properties of halogen‐free epoxy molding compounds (EMCs) for semiconductor encapsulation. In this study, biphenyl‐type resins were used as the epoxy and hardener resin for halogen‐free EMCs to obtain high flame‐retardant properties and high filler contents. Latent catalyst effects were examined with two kinds of EMC compositions, halogen‐free EMCs and conventional EMC compositions. We used triphenylphosphine‐benzoquinone salt (TPP‐BQ) as a latent catalyst. Spiral flow and gel time were measured to investigate the change in moldability with the latent catalyst. We measured package fail, moisture absorption, and delamination for reliability evaluation and flexural strength, flexural modulus, and adhesion for mechanical properties to examine latent catalyst effects. An improvement in moldability, reliability, and the mechanical properties were observed in two types of halogen‐free EMCs with TPP‐BQ as a latent catalyst. These phenomena were seen in conventional EMCs, including o‐cresol novolac epoxy resin. The cure kinetics of these systems were investigated by differential scanning calorimetry with an isothermal approach to explain these phenomena. The results indicate that the improvement in moldability in halogen‐free EMCs with TPP‐BQ was due to the low conversion rate of this system, and the increase in mechanical properties was attributed to the high conversion of curing reaction. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2287–2299, 2005     

Preparation and characterization of trilobal activated carbon fibers

The objective of this research was to evaluate the effectiveness of several different methods for controlling the pore size and pore size distribution in activated carbon fibers. Variables studied included fiber shape, activation time, and the addition of small amounts of silver nitrate. Pure isotropic pitch and the same isotropic pitch containing 1 wt.% silver were melt spun to form fibers with round and trilobal cross sections. These fibers were then stabilized, carbonized, and activated in carbon dioxide. Field emission scanning electron microscopy (FE SEM), electron dispersive spectra (EDS), and wavelength dispersive spectra (WDS) were used to monitor the size and distribution of the silver particles in the fibers before and after activation. Each of these analyses showed that the distribution of silver particles was extremely uniform before and after activation. The fibers were also weighed before and after activation to determine the percent burn-off. The BET specific surface areas of the activated fibers were determined from N₂ adsorption isotherms measured at −196 °C. The results showed that round and trilobal fibers with equivalent cross-sectional areas yielded similar burn-off values and specific surface areas after activation. Also, activation rates were found to be independent of CO₂ flow rate. The porosity of the activated fibers depended on the total time of activation and the cross-sectional area of fibers. The N₂ adsorption measurements showed that the activated fibers had extremely high specific surface areas (greater than 3000 m²/g) and high degrees of meso- and macro-porosity. FE SEM was also used to investigate surface texture and size of pore openings on the surfaces of the activated fibers. The photos showed that silver particles generated surface macro- and mesopores, in agreement with the inferences from N₂ adsorption measurements.     

A study on the factors for improving the ethanol production from Jerusalem artichoke by Kluyveromyces fragilis

This study is to investigate the factors influencing the alcohol production byKluyveromyces fragilis using the juice of Jerusalem Artichoke tubers. The cell growth rate and ethanol production rate were stimulated by aeration and by the addition of unsaturated fatty acids and the cell mass production and the ethanol production were substantially improved. It was found that oxygen and unsaturated fatty acids added played a decisive role on the increase of alcohol tolerance of yeast.     

Companion robots for older adults: Rodgers’ evolutionary concept analysis approach

Intelligent Service Robotics - This study aims to analyze the concept of companion robots for older adults from the perspective of nursing. This study employed a concept analysis. The literature...     

Process for dense 2D SiC fiber-SiC matrix composites

A new process using SiC fiber fabrics and SiC tapes to produce dense 2D SiC fiber-SiC (SiC/SiC) composites is demonstrated. The strategy for fabricating the SiC/SiC composites involves: (i) alternately stacking the SiC fiber fabrics and SiC tapes at room temperature, (ii) pyrolyzing of the stacked composites, and (iii) hot-pressing the pyrolyzed composites. By controlling the hot-pressing temperature, it is possible to obtain dense 2D SiC/SiC composites with relative densities of >98%. The 2D SiC/SiC composites show no degradation of the SiC fibers and a higher mechanical strength.     

The form error prediction in side wall machining considering tool deflection

In this research, an effective method for the form error prediction in side wall machining with a flat end mill is suggested. The form error is predicted directly from the tool deflection without surface generation by cutting edge locus with time simulation. The developed model can predict the surface form error accurately about 300 times faster than the previous method. Cutting forces and tool deflection are calculated considering tool geometry, tool setting error and machine tool stiffness. The characteristics and the difference of generated surface shape in up milling and down milling are discussed. The usefulness of the presented method is verified from a set of experiments under various cutting conditions generally used in die and mold manufacturing. This study contributes to real time surface shape estimation and cutting process planning for the improvement of form accuracy.