Trenched‐Sinker LDMOSFET (TS‐LDMOS) Structure for 2 GHz Power Amplifiers

This paper proposes a new LDMOSFET structure with a trenched sinker for high‐power RF amplifiers. Using a low‐temperature, deep‐trench technology, we succeeded in drastically shrinking the sinker area to one‐third the size of the conventional diffusion‐type structure. The RF performance of the proposed device with a channel width of 5 mm showed a small signal gain of 16.5 dB and a maximum peak power of 32 dBm with a power‐added efficiency of 25% at 2 GHz. Furthermore, the trench sinker, which was applied to the guard ring to suppress coupling between inductors, showed an excellent blocking performance below ?40 dB at a frequency of up to 20 GHz. These results confirm that the proposed trenched sinker should be an effective technology both as a compact sinker for RF power devices and as a guard ring against coupling.     

Post-Event Rumination and Negative Self-Appraisal in Social Phobia Before and After Treatment.

This study investigated the relationship between self-appraisals of performance, symptom severity and post-event rumination in social phobia, and evaluated the effect of treatment on these variables. A socially phobic group and a nonanxious control group performed an impromptu speech and were told that their performance would be evaluated. Participants appraised their performance immediately after the speech and 1 week later, and the frequency of post-event rumination during the week following the speech was assessed. The socially phobic group maintained the negative appraisals of their speech over the week, whereas the nonclinical group showed increased positivity about their performance The socially phobic group also engaged in more negative rumination than controls. Treatment improved perceptions of performance and reduced negative rumination. These results are discussed in the light of cognitive models of social phobia. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Tensile fracture and failure behavior of technical flax fibers

The apparent tensile strength of technical flax fibers was determined in single‐fiber tests at various clamping lengths (20, 40, and 80 mm) and the outcome was compared with literature data. It was demonstrated that the strength of flax at each clamping length obeyed the two‐parameter Weibull model. The failure mode and sequence were studied in situ (i.e., during loading) by SEM and acoustic emission (AE). The failure sequence (axial splitting of the technical fiber along its elementary constituents, radial cracking of the elementary fibers, multiple fracture of the elementary fibers) concluded reflected the hierarchical build‐up of the flax bast fibers. To the above failure events AE amplitude ranges were assigned. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3638–3645, 2003     

Positively Thermo‐Sensitive Monodisperse Core–Shell Microspheres

In this paper, we report on a novel family of monodisperse thermo‐sensitive core–shell hydrogel microspheres that is featured with high monodispersity and positively thermo‐responsive volume phase transition characteristics with tunable swelling kinetics, i.e., the particle swelling is induced by an increase rather than a decrease in temperature. The microspheres were fabricated in a three‐step process. In the first step, monodisperse poly(acrylamide‐co‐styrene) seeds were prepared by emulsifier‐free emulsion polymerization. In the second step, poly(acrylamide) or poly[acrylamide‐co‐(butyl methacrylate)] shells were fabricated on the microsphere seeds by free radical polymerization. In the third step, the core–shell microspheres with poly‐ (acrylamide)/poly(acrylic acid) based interpenetrating polymer network (IPN) shells were finished by a method of sequential IPN synthesis. The proposed monodisperse core–shell microspheres provide a new mode of the phase transition behavior for thermo‐sensitive “smart” or “intelligent” monodisperse micro‐actuators that is highly attractive for targeting drug delivery systems, chemical separations, sensors, and so on.     

High‐Performance,Monolithic Polyaniline Electrochemical Actuators

New polyaniline (PANI) asymmetric membranes were fabricated using a phase‐inversion technique with hexane as the coagulation bath. These membranes exhibit a dense structure with macrovoids distributed asymmetrically throughout the cross‐section. A stress–strain study demonstrated that the Young's modulus (1.421 GPa) and strain at break (7.6 %) of the new PANI asymmetric membranes prepared from hexane are approximately 12 and 4 times higher, respectively, than the values reported previously for the PANI integrally skinned asymmetric membranes (ISAMs) (123 MPa Young's modulus and 1.8 % strain at break). Furthermore, monolithic electrochemical actuators based on a single PANI asymmetric membrane were constructed, and a bending movement of up to 20 Hz was experimentally recorded in a hydrochloric acid aqueous solution. A lifetime of over 329 500 cycles was determined for these actuators at a ± 2° angular displacement (5 Hz). The lifetime is limited by a bending fatigue that creates a transversal crack on the PANI membrane at the air–water interface. Control over the actuator movement is also manifested by the linear dependences of the bending angle on the charge and of the angular velocity on the current. These relationships are independent of both the kind of applied electric signal and the frequency used.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Lipase‐catalyzed dynamic kinetic resolution of (R,S)‐fenoprofen thioester in isooctane

A lipase‐catalyzed enantioselective hydrolysis process under in situ racemization of the remaining (R)‐thioetser substrate with trioctylamine as the catalyst was developed for the production of (S)‐fenoprofen from (R,S)‐fenoprofen 2,2,2‐trifluoroethyl thioester in isooctane. Detailed investigations of trioctylamine concentration on the enzyme activation and the kinetic behavior of the thioester in racemization and enzymatic reactions were conducted, in which good agreement between the experimental data and theoretical results was observed. © 2002 Society of Chemical Industry     

Baseline Determination in Construction Labor Productivity-Loss Claims

Various ways of quantifying damages have been applied to productivity loss claims in construction. All of the ways attempt to be as objective as possible based on the extent of information available in a particular case. The measured mile, a widely accepted method, is employed when an unimpacted baseline period of production can be identified. Although that approach is considered to be the most objective method available in such cases, the method is limited and does not directly account for variation in individual productivity values about a normal or natural level of productivity. A gap exists between the use of existing methods and the availability of an appropriate methodology that specifically addresses variation in productivity. The key lies in the way baseline productivity is measured, which is inherently statistical, yet no truly statistical methods are used to establish such a baseline. Using the measured mile as a backdrop, this article provides an objective, measurement-based approach that can be used to establish a productivity baseline applied to construction productivity loss claims, based on the application of statistical methods aided by a process control chart. The focus is on providing the basic principles and concepts underlying the approach presented.