An automatic method for controlling the centre of gravity of a model

In many applications the location of the centre of gravity of a mechanical part is an important factor that a designer must consider. If it is not in a desired location, a part might not work properly, e.g. unbalanced force might be generated in a rotational part. After a part is modeled, its centre of gravity cannot be altered unless its external shape or internal mass distribution is changed. However, the external shape is usually constrained by other design considerations. In this paper, an algorithm is proposed for controlling the centre of gravity of a hollowed part. Using this algorithm, the location of the centre of gravity of a part is controlled by changing its internal mass distribution.     

A transmit/receive IF chip set for WCDMA mobiles in 0.35 /spl mu/m CMOS

An implementation of the IF section of WCDMA mobile transceivers with a set of two chips fabricated in an inexpensive 0.35-/spl mu/m two-poly three-metal CMOS process is presented. The transmit/receive chip set integrates quadrature modulators and demodulators, wide dynamic range automatic gain control (AGC) amplifiers, with linear-in-decibel gain control, and associated circuitry. This paper describes the problems encountered and the solutions envisaged to meet stringent specifications, with process and temperature variations, thus overcoming the limitations of CMOS devices, while operating at frequencies in the range of 100 MHz-1 GHz. Detailed measurement results corroborating successful application of the new techniques are reported. A receive AGC dynamic range of 73 dB with linearity error of less than /spl plusmn/2 dB and spread of less than 5 dB for a temperature range of -30/spl deg/C to +85/spl deg/C in the gain control characteristic has been measured. The modulator measurement shows a carrier suppression of 35 dB and sideband/third harmonic suppression of over 46 dB. The core die area of each chip is 1.5 mm/sup 2/.     

机电一体化技术在综合采煤设备中的应用与发展

介绍了机电一体化技术在国内外煤矿井下综采设备中的应用，并论述了机电一体化技术发展与相关技术的研究。     

空间桁架结构拓扑优化设计的线性规划方法

本文以杆件内力为设计变量,构造了多工况作用下空间桁架结构拓扑优化的线性规划模型,考虑了应力和位移约束,能够避免奇异最优拓扑和不稳定结构的产生。     

数据压缩的综合字典模型

文中提出一种无损的数据压缩的字典方法，被称为综合字典方法，该方法在较大程度上消除数据文件中多种形式的冗余，达到较好的压缩效果。     

基于移动Agent技术的QoS保障机制

介绍了移动Agent的基本特性。移动Agent可在异构的网络各个节点间自由地移动,它能感知网络的状态,监控系统并与其他Agent进行交互。IETF的IS模型采用了RSVP(ResourcereSerVationProtocol)协议对系统资源进行预留,从而达到一定程度上保障所需QoS的目的。QoS保障机制将移动agent技术与RSVP协议结合起来,通过资源预留和agent动态移动的实现可以达到更好地改善QoS的目的。     

I-slot characteristics

I-shaped slots will fit entirely on the rectangular waveguide narrow wall without wrapping onto the broad wall. This slot type is suitable for single plane scan-phased arrays where element spacing, in the scan plane, is equal to or less than one-half wavelength. The method of moments solution for the I-slot is presented. Comparison of computed results with measured data illustrates the validity of this solution. To facilitate future designs, the waveguide scattering parameters and the radiation characteristics of I-slots are included     

Assessment of underground cable ratings based on distributed temperature sensing

Numerous power utilities have installed advanced distributed temperature sensing (DTS) systems to measure the temperature of underground cables. This paper presents a general procedure for real-time assessment of underground cable ratings based on DTS. After the identification and location of hot spots on a cable, the cable installation data, load, and DTS-recorded temperature over a period of time are used to estimate soil thermal parameters and assess cable ratings under normal and overloading conditions. In order to accurately estimate soil thermal parameters, a combined technique of the finite-element method and gradient-based optimization is used. The technique was validated in the laboratory and applied to a rating assessment of a 230-kV/500-MVA cable circuit. The assessed continuous and emergency ratings are helpful in improving the operation of this circuit.     

Exploratory analysis of brain connectivity with ICA.

Covariance-based methods of exploration of functional connectivity of the brain from functional magnetic resonance imaging (fMRI) experiments, such as principal component analysis (PCA) and structural equation modeling (SEM), require a priori knowledge such as an anatomical model to infer functional connectivity. In this research, a hybrid method, combining independent component analysis (ICA) and SEM, which is capable of deriving functional connectivity in an exploratory manner without the need of a prior model is introduced. The spatial ICA (SICA) derives independent neural systems or sources involved in task-related brain activation, while an automated method based on the SEM finds the structure of the connectivity among the elements in independent neural systems. Unlike second-order approaches used in earlier studies, the task-related neural systems derived from the ICA provide brain connectivity in the complete statistical sense. The use and efficacy of this approach is illustrated on two fMRI datasets obtained from a visual task and a language reading task.