Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Proton exchange membranes by radiation grafting of styrene onto fep films. III. Structural investigation

Structural investigation on proton-exchange membranes, obtained by the radiation grafting of styrene onto FEP films and subsequent sulfonation, was carried out by differential scanning calorimetry. The membrane crystallinity was found to show a decreasing trend with increasing degree of grafting. The melting temperature of all the membranes also showed a slight decrease as compared to the ungrafted FEP. The results have been explained in terms of the cumulative effect of the decrease in the crystalline/amorphous ratio by the incorporation of amorphous polystyrene grafts and of disruption of spherulitic crystallites of the FEP component in the membranes. The glass transition temperature of the membranes with different water contents was also evaluated. A correlation of the glass transition temperature with the residual water in dried membranes was established. © 1994 John Wiley & Sons, Inc.     

Evaluation of refractive index approximations used for modedetermination in multiple quantum well slab waveguides

Approximations commonly used to determine the effective indexes of the guided modes of optical waveguides formed using multiple quantum well (MQW) materials are compared to the exact solutions in the slab waveguide model. Modeling the quantum well region as a single homogeneous layer with an average index of refraction is shown to produce results in close agreement with exact values of the effective index. A geometrically weighted average of the indexes provides the most accurate approximation for typical values of index and layer thickness of GaAs-Al_xGa_1-xAs quantum well waveguides     

Satellite broadcasting of time and frequency signals

The authors discuss the advantages of broadcasting time from a satellite over the more traditional ground based methods such as short wave and low frequency standard time and frequency broadcasts. The authors describe several one way satellite time services currently operational and discuss, in particular, a broadcast service using the Indian domestic satellite INSAT. The signal format, transmitting and receiving setups, and the methods for satellite position prediction are described in detail for the INSAT broadcast. Some typical results of time and frequency calibration are also discussed     

Liquid phase epitaxial growth of pure and doped GaSb layers: morphological evolution and native defects

Undoped and Te-doped gallium antimonide (GaSb) layers have been grown on GaSb bulk substrates by the liquid phase epitaxial technique from Ga-rich and Sb-rich melts. The nucleation morphology of the grown layers has been studied as a function of growth temperature and substrate orientation. MOS structures have been fabricated on the epilayers to evaluate the native defect content in the grown layers from theC-V characteristics. Layers grown from antimony rich melts always exhibitp-type conductivity. In contrast, a type conversion fromp- ton- was observed in layers grown from gallium rich melts below 400 C. The electron mobility of undopedn-type layers grown from Ga-rich melts and tellurium doped layers grown from Sb- and Ga-rich solutions has been evaluated. Paper presented at the poster session of MRSI AGM VI. Kharagpur. 1995     

A parametric study of strength reduction factors for elasto-plastic oscillators

Strength reduction factors (SRFs) continue to play a key role in obtaining design forces from elastic design spectra (via response modification factors) in ductility-based earthquake-resistant design. Despite several years of sustained research efforts, it has not been conclusively shown how SRF for a given singledegree-of-freedom structural system depends on various source and site parameters. A parametric study is carried out here for the explicit dependence of SRF spectrum (describing variation of SRF with system period for a given ductility demand) on strong motion duration, earthquake magnitude, geological site conditions, and epicentral distance in case of (non-degrading) elasto-plastic oscillators. For this, scaled response spectra are considered for different combinations of earthquake magnitude, site conditions and epicentral distance, and SRF spectra are generated from 1274 accelerograms recorded in western USA after making those compatible with each of these spectra. It is shown that there is no clear and significant dependence of SRF spectrum on strong motion duration. Further, the parametric dependence on earthquake magnitude, site conditions, and epicentral distance broadly conforms to the trends reported by earlier investigations. In particular, this study confirms that the dependence of SRF spectra on earthquake magnitude should not be ignored. This paper has been contributed in honour of Professor R N Iyengar, Indian Institute of Science, on the occasion of his formal retirement.     

A Study of Interspeaker Variability in Speaker Verification

We propose a new approach to the problem of estimating the hyperparameters which define the interspeaker variability model in joint factor analysis. We tested the proposed estimation technique on the NIST 2006 speaker recognition evaluation data and obtained 10%-15% reductions in error rates on the core condition and the extended data condition (as measured both by equal error rates and the NIST detection cost function). We show that when a large joint factor analysis model is trained in this way and tested on the core condition, the extended data condition and the cross-channel condition, it is capable of performing at least as well as fusions of multiple systems of other types. (The comparisons are based on the best results on these tasks that have been reported in the literature.) In the case of the cross-channel condition, a factor analysis model with 300 speaker factors and 200 channel factors can achieve equal error rates of less than 3.0%. This is a substantial improvement over the best results that have previously been reported on this task.     

Design development of a static sunshade using small scale modeling technique

The rising global demand for energy has triggered emphasis on conservation of energy. Buildings are one of the important energy consuming sectors. Passive solar architecture encompasses a wide range of strategies and options resulting in energy efficient building design and increased occupant's comfort. Passive solar design, aiming at increasing direct solar gains during winter period and to avoid overheating during summer period should make use of specific shading devices over energy efficient window. The static sunshades are most effective for solar control inside the buildings.Countries like India have composite climate, which can be classified under summer, winter and rainy season. Depending on the seasonal requirements, this paper introduces a new geometry of a static sunshade, designed by calculating the sun angles for the two dates. The static sun shading design methodology is validated with the help of small scale modeling experimentation technique, carried out in Pilani, Rajasthan (India). Although insulating materials can be used as a part of a building structure, its feasibility should be checked before particular application. In the present paper, the two small-scale experimental models of actual construction material with varying static sunshades, i.e. horizontal and the proposed one have been constructed and analyzed with the models of insulating material (Polyurethane Foam [PUF]). Depending upon the solar intersection over south facade wall, sunlit area and shaded area have been correlated with temperature inside the models to decide the effectiveness of the proposed sunshade.     

Synthesis and characterization of acidic properties of Al-SBA-15 materials with varying Si/Al ratios

Al-SBA-15 of varying Si/Al ratios in the range 11.4–78.4 was synthesized using tri-block copolymer P123. The calcined materials were examined by XRD, pore size distribution, surface area, ²⁷Al NMR spectroscopy. The acidity and acid strength distribution were studied using microcalorimetric adsorption of NH₃. The acidic properties were also examined by cumene cracking reaction as a function of Si/Al ratios. Systematic variation of acidity and activity was observed as a function of Si/Al ratio. The initial heats of NH₃ adsorption correlated well with activity indicate that acid sites with ΔH > 100 kJ/mole is responsible for cumene cracking activity. Linear correlations were obtained with total acidity and cumene cracking activities. The tetrahedral aluminum was found to be responsible for the observed acidities and catalytic activities.