A new voltage control equipment using fuzzy inference

Power system control equipment needs higher sensitivity and operational reliability. Advanced voltage control equipment is needed for reducing the frequency of tap changes and improving the characteristics (the relationship between the actual voltage and reference voltage) of the voltage to meet today's power system requirements. However, these objectives are in a trade-off relationship. Studies of voltage control derived from a knowledge base suitable for electric power systems can satisfy these objectives using fuzzy inference. Compared with corresponding conventional equipment, the new equipment improved the deviation of 30 min average voltage of 30 percent. This paper describes the design concept of new voltage control equipment using fuzzy inference. In addition, field test results are described along with rules of fuzzy inference, membership functions, and the deviation of 30 min average voltage through detailed simulation.     

Influence of buried structure on polarization sensitivity instrained bulk semiconductor optical amplifiers

In order to achieve an accurate design of polarization-insensitive semiconductor optical amplifiers based on tensile strained bulk InGaAsP, the reduction of strain in the active layer of the buried heterostructure and its influence on polarization sensitivity are analyzed numerically for the first time. The gain calculation, including the strain distribution in the active layer, is examined based on the k · p method for the different active layers. It is found that the strain introduced during the epitaxial growth is strongly reduced after regrowth of the burying layer. In an active layer having the aspect ratio of 1 : 4, the strain reduction causes more than a 0.5-dB deviation in the polarization sensitivity of the gain. From a comparison with the experimental results, it is shown that including the effect of the burying layer in the calculation gives an accurate determination of the amount of strain for the polarization independence     

Humidity Sensor Characteristics of Woodceramics

The humidity sensor characteristics of Woodceramics were investigated. The Woodceramics used in this experiment were prepared at 650–900°C. The size of specimens selected was 1 × 1 × 10 mm . One was used as-cut and the other was polished. Above 700°C, the resistance of the specimen was below 50 and the decrease of resistance with increasing relative humidity was small. The specimen prepared at 650°C had a resistance of about 1 k. The resistance of as-cut specimens decreased with increase in relative humidity, but that of the polished specimen did not change significantly. The difference between as-cut and polished samples was explained by the differences in surface micro-structure.     

Studies on sublimation of disperse dye out of dyed polymers. I. Rate of sublimation and amorphous transition points of poly(ethylene terephthalate)

Four samples of poly(ethylene terephthalate) film of various crystallinities and orientation were dyed with p-nitroaniline and disperse dyes. When these films were heated under a 2–3 × 10^?3 mm Hg vacuum at a specified temperature T, the dye sublimed out of the dyed specimen. The amount (M_t/M_∞) of sublimed dye is in linear proportion to the square root of the sublimation time, t^½, where M_t and M_∞ are the amounts of dye sublimed for times t and t = ∞. The diffusion coefficient D, calculated from the slope of the above plot, is independent of the dye concentration of the film. When log D is plotted against 1/T°K over the temperature range 320–520°K, the relation is composed of two to four intersecting lines with the slope decreasing with elevation of temperature and with the breaks at about 89°–98°, 122°–135°, 155° and 175°–176°C. These breaks are the amorphous transitions: the first is the glass transition temperature T_g, the second and the fourth are the amorphous transitions corresponding to the crystalline transition points, i.e., the cold crystallization temperature and the smectic–triclinic transition temperature. With some exceptions, these amorphous transitions are found also by dilatometry and electrical conductivity measurements. The apparent activation energy for diffusion decreases from about 100 kcal/mole for the glass state to 22–24 kcal/mole for the region above 180°C. The activation energy for each region changes slightly with the size of dye molecule and the crystallinity and orientation of the film.     

Morphology,thermal, and mechanical properties of vinylester resin nanocomposites with various organo‐modified montmorillonites

New nanocomposites based on a vinylester resin (VER) and the organo‐montmorillonites (ODA‐M, BHL‐M, DEM‐M, BHLV‐M) modified with octadecylammonium, bis(2‐hydroxyethyl)lauryl ammonium, diethyl[2‐(methacryloyloxyl)ethyl]ammonium, and bis(2‐hydroxyethyl)lauryl(vinylbenzyl)‐ammonium chlorides, respectively, were prepared by dispersing the organoclays in VER, and subsequent crosslinking at finally 120°C. X‐ray diffraction studies and morphological studies using transmission electron microscopy revealed that exfoliation occurs for the VER/ODA‐M and BHL‐M composites, intercalation occurs for the VER/BHLV‐M composite, and neither intercalation nor exfoliation occur for the VER/DEM‐M and unmodified montmorillonite composites. On the whole, although the enhancement in flexural modulus was observed for the exfoliated ODA‐M and BHL‐M composites, the flexural strength was rather lowered. Dynamic viscoelastic measurement revealed that the ODA‐M, BHL‐M, and BHLV‐M nanocomposites have significantly higher storage modulus at the rubbery state than the other composites. Polym. Eng. Sci. 44:2041–2046, 2004. © 2004 Society of Plastics Engineers.     

Oxidation behavior of TiAl coated with a fine-grain Co-30Cr-4Al film

The oxidation behavior of TiAl coupons coated with a fine-grain Co-30Cr-4Al (mass %) film of about 30-m thickness has been studied at 1100–1400 K in a flow of purified oxygen at atmospheric pressure for up to 500 ks. Three oxidation stages were recognized: initial transient, parabolic, and accelerated stages. However, at 1100 K a parabolic stage continues for more than 800 ks. The activation energy for parabolic oxidation agrees with reported values for the oxidation of alumina-former alloys, although the mass gains during the parabolic stages are relatively small at 1200 and 1300 K. Micropores developed mainly at the scale/coating and coating/substrate interfaces as oxidation proceeded. This is attributable to recrystallization of the coating during oxidation and a Kirkendall effect due to preferential diffusion of Co into the substrate. The accelerated oxidation can be explained in terms of the formation of rutile mounds on the scale.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

Compact cryogenic system with mechanical cryocoolers for antihydrogen synthesis

We have developed a compact cryogenic system which cools a vacuum chamber housing multi-ring trap electrodes (MRTs) of an antihydrogen synthesis trap using mechanical cryocoolers to achieve background pressure less than 10(-12) Torr. The vacuum chamber and the cryocoolers are thermally connected by copper strips of 99.9999% in purity. All components are installed within a diametric gap between the MRT of phi108 mm and a magnet bore of phi160 mm. An adjusting mechanism is prepared to align the MRT axis to the magnet axis. The vacuum chamber was successfully cooled down to 4.0 K after 14 h of cooling with heat load of 0.8 W.     

Renal glomerular fibrosis in a cat

Renal glomerular fibrosis was observed in a 1-year-old spayed female Japanese domestic cat that showed clinically advanced renal failure. In the glomeruli, increased homogeneous materials were stained strongly with aniline blue by Masson's trichrome and positive for anti-type III collagen antibody by immunohistochemical staining, causing mesangial sclerosis and capillary collapse. By electron microscopy, randomly arranged fibrils were observed in the expanded subendothelial and mesangial areas, and the fibrils showed periodicity characteristic of collagen fibers in longitudinal sections. These findings of glomerular lesions closely resemble those of human "collagenofibrotic glomerulonephropathy," which has recently been described as a new type of glomerulonephropathy.