Direct observation of time-dependent space charge profiles in XLPEcable under high electric fields

Space charge distribution was measured, applying an electric field of >1 MV/cm to 3 mm thick XLPE cable insulation. Improving the conventional pulse electro-acoustic method, a new method was developed to measure space charge when applying HV to cables. Under high field, hetero charges were formed soon after voltage application, followed by an injection from the cathode. Then intermittent injections of charge packets from the anode took place. The space charge distribution kept changing without becoming stabilized. A simulation was done assuming hysteresis of the injection characteristics. The observed intermittent injection near the anode was qualitatively reproduced using computer simulation     

STRUCTURE FORMATION OF COATED FILMS WITH DISPERSED PIGMENTS DURING DRYING

In the drying of coated films with dispersed pigments, such as floppy disks, the structure of the film is formed during the drying process and depends on the drying condition. It is important to understand the structure formation during drying for the design of the dryer and die better quality of the product. We measured die drying characteristics of the film and determined the structure of dried film experimentally. A qualitative model for the structure formation during drying of the coated film is suggested.     

High repetition rate, wide-aperture KrF lasers for subpicosecondamplification

A high repetition rate, wide-aperture KrF laser with a magnetic switch has been developed. A dynamic response and a core loss of several magnetic materials were measured, resulting in a loss as low as 0.45 J/pulse for a voltage risetime of ~100 ns. A maximum output energy of 2.5 J in 20 ns (FWHM) was obtained with a total efficiency of 2.5% at 20 Hz. The cross section of the output beam was 65×50 mm². Spectral, spatial, and temporal profiles of gain and absorption coefficients were also measured, resulting in a peak gain of 8.5%/cm. An output energy of 410 mJ was extracted in 280 fs with two beams by using this laser as an amplifier     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Model analysis of enzyme monolayer- and bilayer-modified electrodes: the steady-state response.

The steady-state sensor responses of enzyme monolayer- and heterobilayer-modified electrodes were theoretically analyzed with a simple model. Parameters used here are the surface coverage and rate constants of the enzyme, the concentrations and diffusion coefficients of the substrate and mediator, the rate constant of the electrode process, the thickness of the diffusion layer, and the distance between the enzyme and electrode. The sensor response was divided into three factors; the efficiencies of substrate and mediator supply to the enzyme, the enzyme/electrode charge-transfer efficiency, and the potential rate of enzymatic reaction where the supply efficiencies are unity. Contributions of the parameters to these factors or the total sensor response are described by simple formulas. The experimental observations are successfully interpreted in terms of these theoretical results.     

Coherence-Based 3-D and Spectral Imaging and Laser-Scanning Microscopy

The basics of three-dimensional (3-D) and spectral imaging techniques that are based on the detection of coherence functions and other related techniques are reviewed. The principle of the 3-D source retrieval is based on understanding the propagation law of optical random field through the free space. The 3-D and spectral information are retrieved from the cross-spectral density function of optical random field or numerical calculation of the inverse propagation of the cross-spectral density. We will first introduce the coherence-based spectral tomography techniques with low-coherence light sources. These techniques limit their scheme of coherence detection only along the optical axis and some of them achieve simultaneously the high resolution and high speed of detection taking advantage of an imaging lens. We then provided explanations of the principle of 3-D source retrieval that is based on the propagation law of optical random field through the free space along with the introduction of the numerical holography and computed tomography techniques. We will lastly show 3-D spectral imaging schemes with the concurrent laser-scanning cross-sectioning techniques: one is the confocal laser scanning microscopy and the other is the two-photon laser-scanning fluorescence microscopy.     

Temperature Dependence of the Raman Spectrum in Lithium Oxide Single Crystal

Temperature dependence of the Raman spectrum of lithium oxide single crystal has been measured over a temperature range of 80 to 1073 K. The frequency shift and the line width of the Raman spectrum in lithium oxide were about 531 and 4.5 cm^-1 at 80 K, respectively. At 1073 K, the frequency shift and the line width attained the values of 464 and 112 cm^-1, respectively. The strong temperature dependence of the frequency shift and line width was compared with data from some crystals with a fluorite structure.     

REM sleep deprivation potentiates the effects of imipramine and desipramine but not that of clomipramine in the forced swimming test

The human amnestic syndrome associated with lesions of the hippocampus and amygdala is characterized by a selective impairment of recent (explicit, episodic) memory. Benzodiazepine (BZ) treated normal subjects demonstrate similar, marked impairments in episodic memory, but in addition, BZ also induces sedation and inattention. Thus, the amnestic effects of BZ may be secondary to drug-induced sedation. However, when subjects were pretreated with the specific BZ receptor antagonist, flumazenil, the sedative and attentional effects of diazepam were blocked, but a marked impairment in episodic memory still occurred. This demonstrates that, using neuropharmacological methods, it is possible to produce a dissociation of memory impairment from inattention and sedation. Such distinct patterns of cognitive dysfunction may serve as models for clinical cognitive syndromes.     

Effective sludge solubilization treatment by simultaneous use of ultrasonic and electrochemical processes.

Sludge disintegration treatment by using simultaneously ultrasonic irradiation and electrolysis was investigated experimentally. A lab-scale diaphragm cell irradiated with ultrasound at a constant oscillating frequency of 20 kHz was used as a reactor. The batch experiments were carried out under different conditions of electric outputs of the ultrasonic generator, electric current for the electrolysis and different initial SS concentrations. A simultaneous treatment in the cathodic compartment without any chemical doses considerably facilitated the sludge solubilization, compared to the sonication alone. An increase in the electric current up to 400 mA under a constant ultrasonic density decreased the specific energy by 55% within the experimental range. The specific energy consumption was also reduced when the initial SS concentration increased. In addition, before carrying out the simultaneous treatment, a brief electrolysis was effective for further reduction of the specific energy and the acceleration of soluble COD generation.     

Changes in the thermomechanical behavior of epoxy glasses under the state of strain aging

Changes in thermomechanical behavior with structural relaxation taking place in epoxy glasses were studied. Differential scanning calorimetry measurements and thermostimulated strain recovery tests were performed for specimens deformed and then aged under fixed strain. In the course of heating, the specimens started to absorb thermal energy, whereas plastic strain was still stable. At higher temperatures, plastic strain started recovery, which was accompanied by exothermic behavior of the specimen. With an increase in the aging duration, the endothermic peak signified and moved to a higher temperature. These results indicated that the longer the aging duration was, the harder the plastic strain and strain energy were frozen in the glassy structure. This freeze‐strain phenomenon was observed for crosslinked epoxy glass, as well as polymeric glasses with linear molecular structures, aged under strain. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008