Effect of stress wave shape on the crack propagation velocity in cyclic delayed failure

Crack propagation velocity in delayed failure under superposed repeating load, ($\text{d}\text{a/}\text{d}\text{t)}{}_{\mathrm{R}}$, was compared with that under static load, ($\text{d}\text{a/}\text{d}\text{t)}{}_{\mathrm{S}}$Two peaks appear on the relation between decreasing rate of crack propagation velocity, $\text{1-β = 1 ? (}\text{d}\text{a/}\text{d}\text{t))}{}_{\mathrm{R}}\text{/(}\text{d}\text{a/}\text{d}\text{t)}{}_{\mathrm{S}}$ and frequency, ?, both under sinusoidal and square load. By changing the ratio of holding time at maximum stress intensity factor to that at minimum stress intensity factor in square load, it was deduced that the existence of two peaks on the 1 ? β vs $\text{f}$ curve was caused by an asymmetric interaction between hydrogen atoms and cyclic moving of the position with triaxial tensile stress at crack tip. Moreover, the relation between 1 ? β and $\text{f}$ under the positive or negative saw tooth load could be well explained by the interaction model.     

Three-dimensional time-averaged void fraction distribution measurement technique for BWR thermal hydraulic conditions using an X-ray CT system

We have developed a void fraction distribution measurement technique using the three-dimensional (3D) time-averaged X-ray computed tomography (CT) system to understand two-phase flow behavior inside a fuel bundle for boiling water reactor (BWR) thermal hydraulic conditions of 7.2 MPa and 288 °C. As a first step, we measured the 3D void fraction distribution in a vertical square (5?×?5) rod array that simulated a BWR fuel bundle in the air–water test. A comparison of the volume-averaged void fractions evaluated by the developed X-ray CT system with those evaluated by a differential pressure transducer showed satisfactory agreement within a difference of 0.03. Thus, we confirmed that the developed system could be used to get 3D imaging of the vertical square rod array used in the test under the BWR operating pressure condition. In the next step, we did a verification test using the vertical pipe (11.3 mm ID) for BWR thermal hydraulic conditions. A comparison of the cross-sectional-averaged void fractions evaluated by the X-ray CT system with those evaluated by the drift-flux model showed good agreement within a difference of 0.05. We confirmed that the evaluated void fraction distribution forms in the horizontal cross section changed with the quality in response to the flow regime transition.     

绕击雷侵入波下1 100 kV电气设备的绝缘配合研究

用电气几何模型(A-W theory)和EMTP程序定量研究了中国特高压变电站设备的绝缘配合问题。与出厂雷电冲击试验电压波形不同,由绕击雷电侵入波在主变压器上产生的电压波形在波头有高频振荡且波尾时间长。考虑多重雷的绕击雷电侵入波,在线路入口安装瓷柱式避雷器和罐式避雷器可以更好地保护断路器和高抗。     

Basic study of a ship navigator's mental workload using salivary NO\documentclass{article}\usepackage{amsmath}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{amsfonts}\pagestyle{empty}\begin{document}$_{3}^{-}$ \end{document}

Evaluation of the mental workload during training for ship handling has usually depended on professionals (captain, pilot) who have lots of experience on board. We are attempting to evaluate a ship navigator's mental workload based on a physiological index. The physiological indices, namely heart rate variability (R–R interval), nasal temperature, and salivary amylase, are good indices for reading the mental workload during ship handling. Moreover, we find the possibility of using salivary NO$_{3}^{-}$ as a good index for evaluating the ship navigator's mental workload. Salivary NO$_{3}^{-}$ is expected to have a specific characteristic to represent quick response on the spot and the trend. We confirmed the response of students during simulator training, and then carried out the experiment on professionals on a real ship. We propose that salivary NO$_{3}^{-}$ can show a ship navigator's stress for ship handling in the simulator and on a real ship. This work to evaluate the ship navigator's mental workload using salivary NO$_{3}^{-}$ is the first attempt worldwide. © 2013 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Component-based robot system design for grasping tasks

The paper presents a robot system design with highly reusable components for a component-based robot system for manipulation tasks. The robot system is designed based on the analysis of manipulation tasks using a unified modeling language use case diagram. For a service robot with locomotion and manipulation mechanisms, reusability of robot system components is improved by adopting the proposed design. Our structure consists of scenario, task, robot information management server, data analyzer, sensor hardware controller, skill, and motion hardware controller on a component-based robot system. Based on the proposed robot system, we implemented a component-based robot system and subsequently realized a grasping motion by a service robot.     

Flight Model Performance of 640-GHz Superconductor–Insulator–Superconductor Mixers for JEM/SMILES Mission

Performances of 640-GHz Superconductor–Insulator–Superconductor (SIS) mixers developed for the Superconducting Submillimeter-Wave Limb-Emission Sounder (SMILES) mission are described. SMILES, launched in September 2009, is the first mission to observe atmosphere from space using superconducting mixers. Ground test performances of the SIS mixers show very flat gain and noise characteristics in their observation bands in compliance with the specifications required for SMILES.     

Monte Carlo simulation of circular double-stranded polymers

Double-helix structure of DNA provides an appropriate model system for studying equilibrium properties of macromolecule. In contrast to the models of linear polymers, the secondary structure as well as most of interaction parameters can be introduced into the model. We present studies of double-stranded twisted circular polymer chain by mean of computer simulation. The attention was focused on the effect of polymer chain twisting on the properties of macromolecule. We found that the number of double helical turns affects the scaling of the polymer chain and markedly changes system properties, for example, coil to globule transition temperature.     

Prediction of the capacity of a heat exchanger by a thermal network method: Modified effective specific heat model considering the influence of static pressure distributions of refrigerants

In this paper, we proposed a method to predict the capacity of a heat exchanger by considering static pressure distributions of refrigerants. The thermal network method was modified by adding an equivalent heat generation term into a heat balance equation that was connected with calculated 1D static pressure distributions of refrigerants. An experiment was performed with a heat exchanger having two rows and two passes to verify the accuracy of the proposed method. The result showed the error of the predicted capacity to be less than 1% for an evaporator and less than 2% for a condenser. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(5): 376–390, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10039     

Development of coincidence transmission electron microscope. III. Incorporation with gamma-type imaging energy filter

We have developed a new analytical transmission electron microscope (TEM), called coincidence TEM, which, in principle, enables observation of elemental mapping images at a high signal-to-noise ratio. We have previously reported the successful observation of an elemental mapping image of a specimen, but over a very long period of time (168 h). To solve this inefficiency, we installed a gamma-type imaging energy filter in the coincidence TEM to remove the no-loss electrons, which are mainly transmitted electrons. This has enabled the intensity of the background signals in the coincidence measurement to be markedly reduced. The coincidence TEM with a gamma-type imaging energy filter allows the coincidence image to be observed in 3 h, thus, the measurement time is shortened by two orders of magnitude. Moreover, the use of a silicon drift detector (SDD) will shorten the measurement time.