Change of characteristics of desulfurization and denitrification by combustion flue gas composition and electrode configuration under pulsed corona discharge

Laboratory-scale and parametric experiments of SO₂ and NO_x removal from the simulated combustion gas by pulsed corona discharge have been performed by changing the combustion gas composition and temperature, the electrode configuration of plasma reactor, and the polarity of high-voltage electrode. The following results are obtained: 1) the higher the concentration of H₂O and O₂, the higher the efficiency of desulfurization and denitrification at the same specific input; 2) the pulsed corona discharge with a voltage pulsewidth as short as 200 ns of negative polarity shows the possibility to attain almost 90 percent deSO_x and deNO_x efficiency at the specific discharge input of 20 J/g, which is almost the same as the specific input in the electron-beam process; 3) the deNO_x characteristics show a little temperature dependence in the range of 70 to 130°C, but the deSO_x efficiency increases rapidly in the temperature region below 100°C suggesting the thermochemical dependence of deSO_x reaction; 4) when desulfurization and denitrification proceed, the white dendritic powder deposits on the plasma reactor whose composition is identified to be 49 mol% (NH₄)₂SO₄ and 47 mol% of 2NH₄NO₃ · (NH₄)₂SO₄, and the ratio of SO₂, NO and NH₃ of the deposit is almost equal to that of supplied gas.     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

Detection of hepatitis C virus RNA in the liver by in situ hybridization

To examine HCV infection histologically, we attempted non-radioactive in situ hybridization of HCV-RNA in the liver. We amplified cDNA probe (360 base pairs) by PCR using the primers deduced from the core region of the HCV genome. The probe was labelled with digoxigenin by PCR and used for in situ hybridization on paraformaldehyde-fixed frozen liver sections. The hybrids were visualized immunohistochemically with alkaline-phosphatase-conjugated anti-digoxigenin and alkaline-phosphatase substrates. HCV-RNA-cDNA hybrids were detected in 21 of 24 patients with positive serum HCV markers, whereas there were no positive signals in the liver of 12 cases without HCV infection. The signal intensity of HCV-RNA-cDNA hybrids was abolished after RNase treatment. Various other specificity experiments also verified specific hybridization of HCV-RNA-cDNA. HCV-RNA was visualized in liver cells and most of them were regarded as hepatocytes from their characteristic features. The infected hepatocytes were frequently associated with mononuclear cell infiltration. Hepatocytes positive for HCV-RNA were sometimes binuclear and distributed in various patterns among cases tested. The present in situ hybridization of HCV RNA is highly sensitive and specific and the results suggest the host immune response to HCV-infected cells.     

Neutronic and thermodynamic feasibility of UF6-NpF6 fueled transmutation reactor

Transmutation of neptunium, which is contained in radioactive wastes discharged from nuclear reactors, was investigated as a substitutional method for geologic disposal. We proposed a transmutation reactor fueled with a mixture of gaseous ²³³UF₆ and ²³⁷NpF₆. Neutronic and thermodynamic analysis of the reactor revealed the feasibility of the concept. The reactor has two principal advantages: (1) use of the fuel gas enables on-line reprocessing, (2) ²³⁷Np can be transmuted by a high neutron flux. Our calculation indicated that the transmutation rate of ²³⁷Np was 335 g/year/MW_th, which is much larger than the annual yield of ²³²Np in PWR (6.19 g/year/MW_th).     

Boundary type finite element method for surface wave motion based on trigonometric function interpolation

There are many physical phenomena which can be handled by the Helmholtz equation. The equation explains certain phenomena of wave propagation. This paper presents a new finite element method to analyse surface wave motion. The characteristic point of this method is that the interpolation equation is chosen to satisfy the governing Helmholtz equation using trigonometric functions. This follows that the variational functional to be minimized can be formulated such that the integration is limited to the boundary of the element. The numerical solutions obtained are compared with analytical and experimental solutions. From these comparative studies, it is concluded that the present method provides a useful tool for the analysis of surface wave motion.     

Mechanical properties-morphology of rolltruded propylene ethylene block copolymers

Commercially available propylene-ethylene (P/E) block copolymers have been processed by the rolltrusion technique. Properties such as tensile modulus, tensile strength and sample clarity are significantly enhanced compared to the original commercial material. The latter is found to be comprised of ethylene globules distributed uniformly or heterogenously throughout the P/E copolymer, depending upon the manufacturing process. In the rolltruded copolymer, the mechanical and morphological properties depend upon the processing temperature and deformation ratio experienced by the workpiece. The chemical composition of the P/E copolymers also plays a significant part in the improvements in properties induced via rolltrusion that may be carried out below or above the melting temperature of the ethylene component of the copolymers. Differential scanning calorimetry thermograms are very useful in assessing transitional behaviour in this respect and may be used to distinguish between different copolymers (processed and original samples). Correlations among some properties and processing conditions are presented and discussed in relation to polymer composition-processing conditions-morphology-property relationships.     

Analysis of higher information density pregroove model by boundary element method

Using the boundary element method, results of the push-pull ratio of differential output signals from an optical disc pregroove model by simulation are presented. The possibility of achieving higher information density by reducing the track pitch and the beam spot is demonstrated.<>     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Antioxidant activity of anacardic acids

Anacardic acids, 6-pentadec(en)ylsalicylic acids isolated from the cashew Anacardium occidentale L. (Anacardiaceae) nut and apple, were found to possess preventive antioxidant activity while salicylic acid did not show this activity. These anacardic acids prevent generation of superoxide radicals by inhibiting xanthine oxidase (EC 1.1.3.22, Grade IV) without radical-scavenging activity. Notably, the inhibition kinetics of anacardic acids do not follow hyperbolic dependence of enzyme inhibition on inhibitor contents (Michaelis–Menten equation) but follow the Hill equation instead. Anacardic acid (C_15:1) inhibited the soybean lipoxygenase-1 (EC 1.13.11.12, Type 1) catalyzed oxidation of linoleic acid with an IC₅₀ of 6.8 μM. The inhibition is a slow and reversible reaction without residual enzyme activity. The inhibition kinetics indicate that anacardic acid (C_15:1) is a competitive inhibitor and the inhibition constant, K_I, was 2.8 μM. Anacardic acids act as antioxidants in a variety ways, including inhibition of various prooxidant enzymes involved in the production of the reactive oxygen species and chelate divalent metal ions such as Fe²⁺ or Cu²⁺, but do not quench reactive oxygen species. The C₁₅-alkenyl side chain is largely associated with the activity.     

Syntheses and structural properties of four Rb-aluminosilicate zeolites

Four types of Rb-aluminosilicate zeolites were hydrothermally synthesized in pure phase for the first time from Rb-aluminosilicate gels without using any organic structure-directing agent (SDA) under stirring conditions. The crystal structure of each zeolite was refined by Rietveld analysis of the X-ray diffraction (XRD) data. These crystal structures were confirmed to be Rb-mordenite, Rb-merlinoite, a new aluminosilicate zeolite with an ATT framework topology, and Rb-offretite denoted by RMA-1, RMA-2, RMA-3, and RMA-4, respectively. The Si/Al ratio of RMA-1 with an MOR topology varied from 5.3 to 8.0; however, the variation of the Si/Al ratios of the other zeolites was rather small. The crystal system of RMA-2 was tetragonal with space group I4/mmm, where two Rb sites were distributed at the center of an 8-membered ring (MR). On the other hand, two Rb sites in RMA-3 were located at the center of the 8-MR in small two cages. The structure of RMA-4 was identified as the OFF type with a local disorder or defect, which included a small amount of an intergrown ERI phase.