Fabrication of fluorine-terminated diamond-like carbon thin film using a hyperthermal atomic fluorine beam

Surface modification of diamond-like carbon (DLC) film was performed using a hyperthermal atomic fluorine beam on the purpose of production of hydrophobic surface by maintaining the high hardness of DLC film. By the irradiation of atomic fluorine beam of a 1.0 × 10²⁰ atoms/cm², the contact angle of a water drop against the DLC surface increased from 73° to 111°. The formation of CF₃, CF₂ and CF bonding on the modified DLC surface was confirmed from the measurements of X-ray photoelectron spectra and near-edge X-ray absorption fine structure spectra. Irradiation of hyperthermal atomic fluorine beam was concluded to produce insulator fluorine-terminated DLC film, which has high F content on the surface, by the taking of the use of neutral atomic beam as a fluorine source.     

Feasible method,utilizing density changes,for estimating in situ dynamic strength and deformation properties of sand samples

Laboratory tests and design reliability are directly controlled by sample quality. The frozen sampling (FS) method is useful for dynamic strength and deformation tests of undisturbed clean sand. However, it is very expensive and requires considerable equipment. The sample quality of Toyoura sands obtained from 48 mm and 75 mm samplers are scrutinized based on void ratio, dynamic strength and deformation properties through model and cyclic undrained triaxial tests. A conventional method for estimating in-situ dynamic strength and deformation properties of sand samples utilizing density changes is examined and the applicability of the proposed method is discussed for the samples obtained from Niigata sand deposits.The main conclusions obtained from this study are summarized as follows:(1) A conventional method for estimating in-situ void ratio (e₀), D_r, stress ratio (R_L20) in a 20 cyclic time frame and the initial modulus of rigidity (G₀) of sand samples utilizing density changes is proposed.(2) The in-situ R_L20 and G₀ estimated from the proposed method for sand samples from tube samplers were similar to those of frozen sampling and the in-situ modulus of initial rigidity was calculated from the secondary wave velocity for Niigata sand deposits.Therefore, dynamic strength and deformation properties changes, caused by sampling, can be modified appropriately to an in-situ condition by this proposed method.     

Development of gap sensing system for narrow gap laser welding

Narrow gap welding with an oscillation laser beam is one of the effective processes for thick plate welding. To put this welding process into practical manufacturing, a groove-sensing system using image processing for narrow gap welding with an oscillation laser beam is used. This developed system uses still images of the weld zone taken by a coaxial CMOS camera. It can recognize the position of the groove wall by analysing the brightness distribution in the still image. It can then control the oscillation width and the laser-irradiated area by calculating the groove width and the groove centre position. Some narrow gap welding experiments were performed to evaluate the performance of the developed system. The results revealed that the developed system is effective for narrow gap welding with an oscillation laser beam. Using this system, the narrow gap groove can be welded even if the groove width has changed during the welding process.     

Effect of trace Na additions on the hydriding kinetics of hypo-eutectic Mg–Ni alloys

Mg–Ni alloys are among the most promising candidates for solid-state hydrogen storage systems. This paper reveals the effect of Na doping in accelerating initial hydrogen uptake in Mg–Ni alloys using in-situ Synchrotron X-ray powder diffraction. A minimum concentration of approximately 0.2 wt.% Na must be achieved for the alloys to show reasonably fast hydriding kinetics. Surface analysis shows that a Na-modified Mg–Ni surface facilitates the chemisorption and dissociation of hydrogen molecules in the early stage of hydriding as evidenced by a rapid formation of the saturated hydrogen solid solution Mg₂NiH_0.3 from the original Mg₂Ni. The subsequent hydrogen absorption is based on a mechanism of nucleation and growth of MgH₂ where a high density of dislocations develops ahead of the growing hydride-metal interface.     

Influence of temperature on the fatigue strength of compressed-hydrogen tanks for vehicles

The influence of environmental temperatures on the fatigue strength of compressed-hydrogen tanks for vehicles was investigated. The fatigue strength of Type-3 tanks was found to decrease in a low-temperature environment and increase in a high-temperature environment. The Type-3 tank has been subjected to autofrettage to improve fatigue strength. The investigation clarified that the effect of autofrettage changes according to the environmental temperature due to the difference between the coefficients of thermal expansion of carbon fiber reinforced plastic and aluminum alloy. This causes fatigue strength to change with changes in temperature. The Type-4 tank has a very long fatigue life and did not break after 45,000 cycles in a room-temperature or low-temperature environment. In a high-temperature environment, however, the tank broke in fewer than 45,000 cycles. The fatigue of carbon fiber reinforced plastic was promoted in the high-temperature environment, resulting in breakage of the tank. These results indicate that the fatigue strength of the tanks is influenced by the environmental temperature.     

Simplified method for determining cadmium concentrations in rice foliage and soil by using a biosensor kit with immunochromatography

BACKGROUND: The behavior of cadmium in ecosystems needs to be monitored because of the human toxicity of this heavy metal. The need recently arose for a simple and quick on‐site test for trace levels of Cd in food and environmental samples. In response, an immunochromatographic assay kit for detecting Cd was manufactured by Kansai Electric Power Co. of Japan. This kit uses the antigen–antibody complex reaction between the Cd–EDTA complex and an anti‐Cd–EDTA antibody and shows the results in terms of the degree of color developed on a test paper. We previously reported the successful use of this kit to determine Cd concentrations in brown rice. Here, we applied the kit to the determination of Cd concentrations in rice foliage and soil. RESULTS: Cadmium in rice foliage was not extracted successfully by the method used for brown rice. However, it was successfully extracted by 0.1 mol L^?1 HCl solution at a rice foliage:HCl ratio of 1:20, and coexisting metals were removed sufficiently by the column treatment. The Cd concentrations determined by immunochromatographic assay were well correlated with the values obtained by acid decomposition and inductively coupled plasma mass spectrometry. The 0.1 mol L^?1 HCl‐extractable Cd concentration in soil was also determined successfully with the kit. CONCLUSION: Approximate Cd concentrations in rice plants and 0.1 mol L^?1 HCl‐extractable Cd concentrations in soil can be monitored easily and quickly by this method at locations where facilities for acid digestion and precision analysis are not available. Copyright © 2009 Society of Chemical Industry     

Synthesis and chiroptical properties of helical poly(phenylacetylene) bearing optically active chiral oxazoline Pendants

The novel optically active (S)-4-benzyl-2-(ethynylphenyl)-oxazoline (BnEPhOx) was successfully prepared and polymerized using rhodium catalyst ([Rh(nbd)Cl]₂) to obtain the moderate molecular weight poly(phenylacetylene)s bearing chiral oxazoline derivatives with high yields (≥90%). The ¹H NMR spectra demonstrated that the resulting polymers had high stereoregular structures. Moreover, the poly(phenylacetylene)s bearing chiral oxazoline exhibited better thermal stability than poly(phenylacetylene). The resulting polymers showed higher absolute values of optical specific rotation than the monomer. The polymers also exhibited intense CD signal in the region of the π-π1 band of the conjugated polyacetylene backbone in chloroform solution. The results of specific rotation and CD spectroscopy indicated that all the polymers adopted higher-order structure with predominantly one-handed screw sense.In addition, the resulting polymers emitted fluorescence under UV irradiation.