Impedance spectroscopy study and electrical behavior of PMN-PZT actuators joined by ceramic slurry

The solid solution of Pb(Mg,Nb)O₃-Pb(Zr,TiO) O₃ materials have high piezoelectric constant of 600 ∼650 pC/N and electromechanical coupling coefficient k _p of 0.65. Due to such high piezoelectric constant and electromechanical coupling coefficient, Pb(Mg,Nb)O₃-Pb(Zr,TiO)O₃ materials have been attracted attentions for the applications of multilayer ceramic actuators. Actuators can be produced by staking piezoelectric ceramic materials and inner electrodes, alternatively. However, it is difficult to fabricate huge ceramic actuators without any serious problems during the process conditions. Because ceramic are easily cracked during the sintering process, due to strikingly different shrinkage rate between the ceramic materials and metal electrodes. In this research, new jointing methods will be proposed for huge ceramic actuators, and then their electrical properties were investigated. Time dependent leakage current and impedance spectroscopy were employed to expect device performances.     

类似级配沥青混合料最佳油石比关系研究

利用压实热拌沥青混合料的空隙率和矿料间隙率等体积特性，考虑集料吸收沥青的情况，提出了“有效油石体积比”的概念，依据最佳有效油石体积比，分析研究了同类级配矿料的最佳油石比之间的关系，建立了具有普遍意义的关系式，并与新的公路沥青路面施工技术规范提供的预估公式作了比较.     

Selective wet etching of p-GaN for efficient GaN-based light-emitting diodes

The selective wet etching of a p-GaN layer by using a solution of KOH in ethylene glycol (KE) was studied to enhance the optical and electrical performance of the GaN-based light-emitting diodes (LEDs). The surface of the p-GaN, which was selectively etched in the KE solution, showed hexagonal-shaped etch pits. The light-output power of etched LEDs was improved by 29.4% compared to that of the nonetched LED. This improvement was attributed to the increase in the probability of photons to escape due to the increased surface area of textured surface and the reduction in contact resistance of the ohmic layer resulting from the increased contact area and hole concentration on the textured p-GaN. The reverse leakage current of the LED was also greatly decreased due to the surface passivation and the removal of defective regions from the p-GaN.     

Operation, system architectures, and physical Layer design considerations of distributed MAC protocols for UWB

Impulse-based ultra wideband (I-UWB) is an attractive radio technology for large ad hoc and sensor networks due to its robustness to harmful multipath effects, sub-centimeter ranging ability, simple hardware, and low radiated power. To scale to large sizes, networks often implement distributed medium access control (MAC) protocols. However, most MAC protocols for I-UWB are centralized, and they target small wireless personal area networks and cellular networks. We propose three distributed MAC protocols suitable for I-UWB. Two multichannel protocols, called multichannel pulse sense multiple access (M-PSMA) and multichannel ALOHA achieve high aggregate throughput. A busy-signal protocol, called busy-signal multiple access (BSMA), reduces the energy wasted from re-transmitted packets. This paper describes the three protocols in terms of the protocol's operation, the supporting system architecture, and the I-UWB physical layer. Physical layer simulations confirm the feasibility of implementing the proposed systems and also provide parameters for network simulations. Network simulations show that the throughput of M-PSMA exceeds that of a centralized time-division multiple-access protocol and that the energy efficiency of BSMA far surpasses that of other distributed protocols.     

Recrystallization and grain growth of cold-rolled gold sheet

Recrystallization and grain growth of a cold-rolled gold sheet with 98 pct reduction in area (RA) were investigated with electron backscatter diffraction (EBSD) and X-ray diffraction (XRD). Gold with some dopants (Be, Ca, and La) was used in this research and its recrystallization temperature was 320 °C. Isothermal annealing experiments at 400 °C, 500 °C, and 600 °C were carried out for the cold-rolled gold sheet, and recrystallization texture was examined. In the cold-rolled gold sheet, α- and β-fibers were measured mainly and some shear texture components were found on the surface. Shear texture components remained on the surface for 2 hours at 400 °C and were consumed by other recrystallized grains after 24 hours at 400 °C. Microstructure and texture evolution during in-situ annealing at 400 °C were investigated from the cold-rolled state to the fully recrystallized state using EBSD. Most of the newly, recrystallized grains came from the deformed β-fiber regions and consisted of β-fiber, cube, and other random orientations.     

Effects of ZnO on piezoelectric properties of 0.01PMW–0.41PNN–0.35PT–0.23PZ ceramics

The microstructure and piezoelectric properties of the 0.01Pb(Mg_1/2W_1/2)O₃–0.41Pb(Ni_1/3Nb_2/3)O₃–0.35PbTiO₃–0.23PbZrO₃ + 0.1 and 0.3 wt.% Y₂O₃ + x ZnO ceramics were investigated. The crystal structure changed from psudocubic to tetragonal when ZnO added. The average grain size increased from 4 μm to 8 μm with the addition of ZnO by oxygen diffusion, even if the growth rate was low. When ZnO added until 0.5 wt.%, the , k_p and d₃₃ values of specimens were slightly increased regardless Y₂O₃ contents. The curie point of PMW–PNN–PT–PZ ceramics were increased from 162 °C to 232 °C, as increasing the ZnO contents. When ZnO added, the k_p of specimens slightly was increased regardless Y₂O₃ contents. The mechanical quality factors were abruptly decreased regardless Y₂O₃ contents, when ZnO added until 0.75 wt.%. The optimized piezoelectric properties were obtained; d₃₃ = 730 (pC/N), k_p = 60, Q_m = 50, and  = 4750, when PMW–PNN–PT–PZ + 0.3 wt.% Y₂O₃ + 0.5 wt.% ZnO sintered at 1200 °C for 1 h.     

Fuzzy Web ad selector based on Web usage mining

Internet and Web technologies are widely available, making it easier for companies to conduct business and transfer information to customers. Moreover, they speed up financial transactions efficiently, reducing the transaction costs of commercial activities that businesses would normally incur. So, Internet business has created a competitive environment, a successful company wanting to survive and gain a competitive advantage must provide an acceptable bundle of customized services that satisfy customers' needs. Despite the Internet's obvious benefits as a new communication medium its advertising gives the same advertising messages to all customers and so has suffered from poor responses. To raise a Web ad's effectiveness, we propose a Web ad selector that personalizes advertising messages for customers based on their preferences and interests. The Web ad selection system divides Web site customers with similar preferences into several segments through Web usage mining. It uses fuzzy rules that express customer segments' surfing patterns on the basis of expert advice, and recommends appropriate ads by fuzzy inference.     

Off-line, handwritten numeral recognition by perturbation method

This paper presents a new approach to off-line, handwritten numeral recognition. From the concept of perturbation due to writing habits and instruments, we propose a recognition method which is able to account for a variety of distortions due to eccentric handwriting. We tested our method on two worldwide standard databases of isolated numerals, namely CEDAR and NIST, and obtained 99.09 percent and 99.54 percent correct recognition rates at no-rejection level respectively. The latter result was obtained by testing on more than 170000 numerals     

连续时间模糊随机系统分析：状态空间模型分析

研究了连续时间模糊随机系统理论，给出了连续时间模糊随机系统的态变模糊订值映射的定义，讨论并解决了连续时间模糊随机系统的状态空间模型分析。     

固化剂对环氧树脂/蒙脱土纳米复合材料中蒙脱土剥离行为的影响

采用阳离子交换的方法对蒙脱土进行了有机改性，使蒙脱土由亲水性变成亲油性，并使其层间距由原来的1．2nm扩大到2．2nm。分别使用甲基四氢苯酐和4，4’-二胺基二苯基甲烷为固化剂，制备两种环氧树脂／蒙脱土纳米复合材料，并用x一射线衍射仪和透射电镜(TEM)分析有机蒙脱土在环氧树脂中的剥离行为。研究表明，固化剂的选择对有机蒙脱土的剥离行为有很大的影响，用固化剂甲基四氢苯酐和促进剂苄基二甲胺后，有机蒙脱土容易被剥离而得到剥离型的纳米复合材料，而用4，4’-二胺基二苯基甲烷固化剂未能使有机蒙脱土剥离后形成插层型纳米复合材料。