Effect of residual water content on the physico-chemical properties of sucralfate dried gel obtained by microwave drying

The purpose of this study was to investigate the physico-chemical characteristics of sucralfate humid gel dried by microwaves, in relation to the residual water content. Differential scanning calorimetry (DSC) allowed for the determination of the water state in sucralfate samples. Fourier-transform infrared (FT-IR) spectroscopy was used to monitor the changes in sucralfate gel structure induced by the microwave drying. A boundary value of total water content for sucralfate gel samples was found at 42% (w/w). Below this value only bound water was present, whereas above this value, the increase in total water was due to free water. In the physical form of gel, the strength of the coordination between sulfate anions and the positively charged aluminum hydroxide was dependent on the residual water content. The study of the sedimentation behavior of water suspensions prepared with dried sucralfate allowed for the evaluation of the retention of gel properties. We found that the microwave drying process affected the sedimentation of sucralfate dried gel suspensions independent of the residual water content: when suspensions were prepared from sucralfate dried gel powders containing more than 42% (w/w) of residual water, the sedimentation ratio was higher than 0.9. The non-gel powder suspension showed a sedimentation ratio of 0.68 ± 0.02, whereas the sucralfate humid gel suspension did not sediment.     

Feasibility of a long-term low-sodium diet in mild hypertension

The present study set out to assess the feasibility of long-term moderate dietary sodium restriction in patients with mild hypertension in general practice. After screening and a run-in phase of 6-8 weeks, a total of 77 previously undiagnosed mildly hypertensive patients were identified. Half of them were randomized to receive a few simple dietary instructions from their general practitioners in order to reduce salt usage; the others were randomized to receive no advice. The patients were followed up for 12 months with quarterly visits. A total of 56 patients (72.7%) completed the study, 26 on a low-sodium diet (LD) and 30 on their usual diet (UD). At each visit in the diet phase, patients provided 24h urine, which was analysed for volume and sodium concentration in order to assess their sodium intake. Blood pressure, heart the rate and body weight were recorded. The mean urinary sodium excretion for all diet phase visits overlapped in the two groups (177.0 +/- 32.9 vs. 169.3 +/- 49.4 mEq/24h respectively in the LD and UD groups). Nevertheless the mean systolic and diastolic blood pressures for all diet phase visits were significantly lower in the LD than in UD group (144.2 +/- 11.1/91.6 +/- 6.4 and 148.0 +/- 13.7/95.6 +/- 4.7 mmHg respectively, P less than 0.01). Our data suggest that it is not feasible at present to reduce sodium intake in mild hypertensives with simple and inexpensive dietary instructions, the only ones suitable for widespread application in general practice.     

Inversion of a radiative transfer model with hyperspectral observations for LAI mapping in poplar plantations

The potential of radiative transfer modelling and inversion techniques for operational uses is investigated in order to retrieve leaf area index in a poplar plantation. The 1-D bidirectional canopy reflectance model SAIL, coupled with the leaf optical properties model PROSPECT, was inverted with hyperspectral airborne DAIS data by means of an iterative method. The root mean square error in LAI estimation was determined against in situ measurements in order to evaluate the impact of different inversion strategies on the LAI retrieval accuracy. These included the selection of an optimal spectral sampling set, the exploitation of prior knowledge in the inversion process and the use of multiview angle data. We claim that the best configuration is achieved by exploiting multiview DAIS data and prior knowledge information about the model variables (RMSE of 0.39 m² m⁻²). It is also shown that the use of prior knowledge and the selection of a limited number of bands forming the optimal spectral sampling are instrumental in increasing the accuracy of the inversion process. Our analysis confirms the operational potential of model inversion for biophysical parameter retrieval.     

A computer implementation of the partition of the unity procedure and its application to arthropod population dynamics. A case study on the European grape berry moth

This paper presents a new procedure to construct families of spatial approximation-prediction functions which depend on several parameters. The method is based on partitions of the unity. In order to find optimal functions in these families we introduce a Vietoris simplicial set associated to an influence radius. We consider error estimators induced by these Vietoris simplicial sets. A computational implementation of these mathematical models has been developed to be applied to any kind of finite discrete data. Our methods provide a useful tool for the analysis of the spatial distribution of species, which is imperative for developing accurate and efficient management of endangered and invasive species, biological conservation programs, etc. We demonstrate the application of our method to the analysis of the spatial distribution of the grape moth Lobesia botrana (Lepidoptera: Tortricidae) in the vineyards of La Rioja obtaining useful results for the management of this pest.     

High Yield Conversion of Residual Pentoses into Furfural via Zeolite Catalysis and Catalytic Hydrogenation of Furfural to 2-Methylfuran

Xylose was dehydrated over (H⁺) mordenite, using a continuous two-liquid-phase (aqueous-toluene) plug-flow reactor at 260 °C and 55 atm, with 98% conversion rate, 98% furfural molar yield, and 98% furfural selectivity (results from the first pass). Furfural in toluene was hydrogenated over a Cu/Fe catalyst, at 252 °C (gas-phase), in a 99% conversion rate to give 2-methylfuran in a 98% yield (same activity maintained for a 20-h operation).     

Capacitance properties of electrochemically deposited polyazulene films

Polyazulene films formed by electrochemical oxidation of azulene have been studied as active components in electrochemical capacitors. The film shows reversible electrochemical behavior in the positive potential range and exhibits p-doping properties. The influence of film formation conditions on the films electrochemical properties has been investigated. A strong effect of solvent on the polyazulene deposition has been observed. The highest yield of film deposition was found for dichloromethane. Polyazulene films also exhibit stable voltammetric properties in aprotic solvents. The voltammetric response of the film is affected by the size of the anion of the supporting electrolyte. In solutions containing tetra(alkyl)ammonium perchlorates, tetrafluoroborates or hexafluorophosphates, reversible oxidation of polyazulene is obtained. In the presence of large tetra(phenyl)borate anions, polyazulene is irreversibly oxidized upon electrochemical oxidation. The capacitance properties of these materials have been investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The polyazulene film displays a relatively high specific capacitance close to 400 F g⁻¹. Such high value of C_s locates this material among very good polymeric redox pseudo-capacitors.     

LAS glass–ceramic scaffolds by three-dimensional printing

Highly porous (>60% open porosity) glass–ceramic scaffolds with remarkable mechanical properties (compression strength of ～15 MPa) were produced by indirect 3D printing. Precursor glass powders were printed into 3D ordered structures and then heat treated to sinter and develop crystalline phases. The final glass–ceramic contained a β-spodumene solid solution together with a secondary phase of lithium disilicate.The precision of the printed geometry and the density of the struts in the scaffold depended on several processing parameters (e.g. powder size and flowability, layer thickness) and were improved by increasing the binder saturation and drying time. Two types of powders with different particle size distribution (PSD) and flowability were used. Powders with a larger PSD, could be processed within a wider range of printing parameters due to their good flowability; however, the printing precision and the struts density were lower compared to the scaffolds printed using the powder in a smaller average PSD.     

Design Impact on Airflow Patterns in Fluidization Units

The airflow behavior in a fluidization unit was integrally studied by means of experimental work and computational fluid dynamics simulation. The computational domain included the gas inlet pipe, plenum, perforated plate, fluidization chamber, and air outlet pipe. Different scenarios were simulated to allow distinguishing the best way to represent perforated‐plate distributors and elucidate the impact of the grid design on the fluidization performance. The simulated pressure drop across the distributor and the plenum flow pattern were in concordance with the experimental data. It was found that the distance between the peripheral holes and walls has a great impact on the airflow downstream the distributor.