The influence of the processing route on the fragmentation of (Nb,Ti)C stringers and its role on mechanical properties and hydrogen embrittlement of nickel based alloy 718

The nickel-base superalloy 718 is a precipitation hardened alloy widely used in the nuclear fuel assembly of pressurized water reactors (PWR). However, the alloy can experience failure due to hydrogen embrittlement (HE). The processing route can influence the microstructure of the material and, therefore, the HE degree. In particular, the size and distribution of the (Nb,Ti)C particles can be affected by the processing. In this regard, the objective of this work was to analyze the influence of cold and hot deformation processing routes on the development of the microstructure, and the consequences on mechanical properties and hydrogen embrittlement. Tensile samples were hydrogenated through gaseous charging and compared to non-hydrogenated samples. Characterization was performed via scanning and transmission electron microscopies, as well as electron backscattered diffraction. The processing was effective to promote significant variations in average grain size and length fraction of special Σ3ⁿ boundaries, as well as reduction of average (Nb,Ti)C particle size, being these changes more intense for the cold-rolled route. For the mechanical properties, on one side, the cold-rolled route presented the highest increase in ductility for non-hydrogenated samples, while, on the other side, had the highest degree of embrittlement under hydrogen. This dual behavior was attributed to the interaction of hydrogen with the (Nb,Ti)C particles and stringers and its ensuing influence on the fracture processes.     

Large-scale load capacity tests on a geosynthetic encased column

Stone columns have been used to minimize the settlement of embankments on soft soils but their use in very soft soils can become challenging, partly because of the low confinement provided by the surrounding soil. Geosynthetic encased columns (GECs) have been successfully used to enhance to reduce settlements of embankments on soft soils. This paper describes an investigation on the performance of encased columns constructed on a very soft soil using different types of encasement (three woven geotextiles with different values of tensile stiffness) and different column fill materials (sand, gravel and recycled construction and demolition waste, RCDW). The results of load capacity tests conducted on large-scale models constructed to simulate the different types of GECs indicate that the displacement method adopted during column installation can lead to an enhanced shear strength in the smear zone that develops within the very soft soil. In addition, breakage of the column fill material was found to affect the load-settlement response of gravel and RCDW columns. Furthermore, the excess pore water pressure generated in the surrounding soil during installation, was found to remain limited to radial distances smaller than three times the GEC diameter.     

Chronic anal fissure: results of the surgical treatment of 220 patients

Since results from non-surgical procedures designed for treatment of chronic anal fissure are still controversial, sphincterotomy remain as the "state of the art" therapy for this condition. In a retrospective basis, the authors intend to review results from treatment of chronic anal fissure in 220 patients who underwent surgical procedure between 1984 and 1995. Data from chart review included age, sex, location of the lesion at the canal anal, associated anorectal disease, delivered surgical technique and complications. Seventy per cent of the patients were male. Mean age was 37.1 years. Fissure was located at the posterior midline in 86.1%. Associated anorectal conditions occurred in 41.4%. Fissurectomy plus posterior sphincterotomy was the treatment of choice in 84.1%. Complications occurred in 5 (2.3%) cases. There were no incontinent patients. Mean follow-up was 2.6 years. The authors conclude that partial internal anal sphincter section produces excellent results in treatment of chronic anal fissure. Posterior sphincterotomy may persist effective and safe since continence impairment was not identified in the present study.     

Photoinduced Self‐Assembled Nanostructures and Permanent Polaron Formation in Regioregular Poly(3‐hexylthiophene)

Solution processing of conjugated polymers into ordered self‐assembled precursors has attracted great interest in the past years owing to the ability to manipulate their structural and physical properties. Regioregular poly(3‐hexylthiophene) (P3HT) has become the benchmark polymer in this scenario, where ordered lamellar structures significantly improve carrier mobility of the thin films due to increased crystallinity, extended intrachain conjugation, and ordered interchain π‐stacking. Here, a new photoinduced approach is presented for the generation of highly ordered P3HT aggregate structures that is amenable to the use of visible light to control the aggregate formation. Strong intra‐ and interchain interactions in the solution precursors allow for permanent formation of localized and delocalized polarons that are stable for months. Spin‐coated thin films are found to preserve, in part, the morphological and physical properties of the aggregated P3HT solution precursors with high degree of crystallinity and short π‐stack interchain distances.     

Influence of oxygen vacancies on the structural,dielectric, and magnetic properties of (Mn,Co) co-doped ZnO nanostructures

We analysed the variation and effect of oxygen vacancies on the structural, dielectric and magnetic properties in case of Mn (4%) and Co (1, 2 and 4%) co-doped ZnO nanoparticles (NPs), synthesized by chemical precipitation route and annealed at 750 °C for 2 h. From the XRD, the calculated average crystallite size increased from15.30?±?0.73 nm to 16.71?±?012 nm, when Co content is increased from 1 to 4%. Enhancement of dopants (Mn, Co) introduced more and more oxygen vacancies to ZnO lattice confirmed from EDX and XPS. The high-temperature annealing leads to reduction of the dielectric properties due to enhancement in grain growth (large grain volume and lesser number of grain boundaries) with the incorporation of Co and Mn ions into the ZnO lattice. The electrical conductivity of the Mn doped and (Mn, Co) co-doped ZnO samples were enhanced due to increase in the volume of conducting grains and charge density (liberation of trapped charge carriers in oxygen vacancies and free charge carriers at higher frequencies). The Mn-doped and (Mn, Co) co-doped ZnO NPs show ferromagnetic (FM) behaviour. The saturation and remnant magnetizations (M_s and M_r) elevates from (0.235 to 1.489)?×?10^?2 and (0.12 to 0.27)?×?10^?2 emu/g while Coercivity (H_c) reduced from 97 to 36 Oe with enhancement in the concentration of dopants in ZnO matrix. Oxygen vacancies were found to be the main reason for room-temperature ferromagnetism (RTFM) in the doped and co-doped ZnO NPs. The results show that the enhanced dielectric and magnetic properties of Mn doped and (Mn, Co) co-doped ZnO is strongly correlated with the concentration of oxygen vacancies. The observed enhanced RTFM, dielectric properties and electrical conductivity makes TM doped ZnO nanoparticles suitable for spintronics, microelectronics and optoelectronics based applications.     

Kinetics and mechanism of the hydrogen discharge on Ti in HCl-DMSO solutions

The kinetics of hydrogen discharge in solutions of HCl-DMSO is investigated within 10^?3 1 N HCl concentrations, in the presence of KClO₄ as supporting electrolyte. The cathodic slope is 0·120 V/decade for all solutions. The electrochemical reaction order with respect to the hydrogen ion concentration at E = ?0·6 V is found to be 0·52. The stoichiometric number is practically equal to 2. The experimental activation energy is 11·2 kcal/mole.The cathodic process is interpreted with the discharge reaction as rate determining step, followed by the adatom recombination reaction.     

Patch-based reconstruction of surfaces undergoing different types of deformations

We deal with the reconstruction of surfaces that deform under a variety of conditions. The deformation can range from no extension to a certain degree of extensibility. The deformed surface is reconstructed from a single image, given a 3D reference shape. This shape corresponds to the undeformed state of the surface and can be computed using any appropriate technique. In particular, we use homographies defined from two views of the surface. To proceed with the 3D reconstruction of the deformed surface, we assume that the deformations are locally homogeneous and that the overall surface deformation can be obtained by combining the local homogeneous deformations. For this purpose, the surface is split into small patches. For each patch, a mapping between the undeformed and the deformed shapes is computed. The mapping is specified by using the quadratic deformation model Fayad et al. (Proceedings of British Machine Vision Conference (BMVC), 2004). As a result, given the undeformed shape, we define an optimization procedure whose goal is to estimate the 3D positions of deformed points in each image. The optimization is performed on each patch, independently of the others. The experimental results show that this approach allows precise reconstruction of a wide class of real deformations.     

Developing Smart Grids Based on GPRS and ZigBee Technologies Using Queueing Modeling–Based Optimization Algorithm

Smart metering systems have become widespread around the world. RF mesh communication systems have contributed to the creation of smarter and more reliable power systems. This paper presents an algorithm for positioning GPRS concentrators to attain delay constraints for a ZigBee‐based mesh network. The proposed algorithm determines the number and placement of concentrators using integer linear programming and a queueing model for the given mesh network. The solutions given by the proposed algorithm are validated by verifying the communication network performance through simulations.