Temperature-dependent transparency of poly(HPMA-co-DMA) hydrogels: effect of synthesis parameters

The acrylic comonomers hydroxypropyl methacrylate (HPMA) and N,N-dimethylaminoethyl methacrylate (DMA) have been used in several earlier studies to produce pH-responsive hydrogels. However, these same monomers can also be used to prepare hydrogels that are highly responsive to temperature. One manifestation of this temperature sensitivity is a sharp decrease in hydrogel optical transparency that occurs when the temperature exceeds a critical transition value. For example, a hydrogel that exhibits a swelling transition at the physiological pH value of 7.4 has a transition temperature of about 45 °C when the environmental salt concentration is 0.15 M. The value of the transparency transition temperature is shown to depend on hydrogel synthesis parameters such as comonomer mole ratio, crosslinker mole ratio, and even initiator concentration. By reducing the mole ratio of the crosslinker tetraethylene glycol dimethacrylate (TEGDMA), the transition temperature can be lowered by as much as 15 °C. Environmental salt concentration and solvent polarity are also shown to influence the transition temperature.     

Crystal shape monitoring and supersaturation measurement in cooling crystallization with quartz crystal oscillator

A crystallization monitoring system using a quartz crystal oscillator was utilized to predict different shapes of crystal formation by measuring crystal growth rate and to measure supersaturation. Applying different rates of cooling, crystal formation of different shapes was induced, and the frequency variation of the oscillator and the crystal shape observed with an SEM were compared to determine how the frequency variation can be interpreted for the prediction of produced crystal shape. The experimental results obtained from the crystallization of potassium nitrate and cupric sulfate solutions showed that the proposed frequency measurement technique could be applied in the prediction of crystal shape of cooling crystallization processes. In addition, supersaturation was determined from the measurements of solution and coolant temperatures.     

Properties of chitosan‐based biopolymer films with various degrees of deacetylation and molecular weights

An increase in the depolymerization of chitosan was found with an increased concentration of sodium perborate. Acetic anhydride was added to reacetylated chitosan in a molar ratio per gulcosamine unit, and the amide I band of IR spectra changed with the addition of acetic anhydride. Sixteen chitosans with various molecular weights (MWs) and degrees of deacetylation (DODs) were prepared. X‐ray diffraction patterns indicated their amorphous and partially crystalline states. Increases in the chitosan MW and DOD increased the tensile strength (TS). TS of the chitosan films ranged from 22 to 61 MPa. However, the elongation (E) of chitosan films did not show any difference with MW. TS of chitosan films decreased with the reacetylation process. However, E of chitosan films was not dependent on DOD. The water vapor permeabilities (WVPs) of the chitosan films without a plasticizer were between 0.155 and 0.214 ng m/m² s Pa. As the chitosan MW increased, the chitosan film WVP increased, but the values were not significantly different. Moreover, the WVP values were not different from low DOD to high DOD. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3476–3484, 2003     

Absorption of NO x in packed column (I)

A mathematical model for an absorption of nitrogen oxides into water in packed column was developed based on the mass-transfer coefficient in packed column and the chemical reaction accompanying NO _x absorption produces HNO₃ and HNO₂ in the liquid phase. The subsequent dissociation of HNO₂ in the liquid-phase results in the formation of HNO₃ and NO gas, and then this NO gas follows to be oxidized by O₂ in air. The important factors influenced on the absorption of NO _x are the oxidation state of NO gas and the partial pressure of nitrogen oxides in the gas. The efficiency of NO _x absorption increases with the increase of the partial pressure of NO _x . The most critical value for using the model is the constant of .The selection of 11×10⁻⁴kg·mol/atm·m²·sec for resonable for this model.     

Influence of mixing cycle on the degree of mixing of calcite‐filled polyethylene upon stretching

The mixing cycle‐dependent degree of dispersion and degree of mixing of a calcite (calcium carbonate) agglomerate in high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), and linear low‐density polyethylene (LLDPE) matrices upon stretching was investigated using three different techniques: mechanical property, morphological behavior, and image analyzer analyses. The mechanical properties analyzed in terms of the tensile strength and maximum elongation resulted in that the second mixing was the best for giving a better property for all systems except the LDPE system, which exhibited no significant difference between the second and third mixings. The morphological behavior of the three compounds were different, but no distinctive difference was observed to differentiate the degree of mixing from system to system. The number‐, weight‐, and z + 1‐average diameters of the air hole and the aspect ratio upon the stretching and mixing cycle were calculated to analyze the degree of mixing of the calcite‐filled composites. As a consequence, no difference in the average diameter of the air hole was obtained among the three systems, but the aspect ratios of the air hole varied significantly. Thus, the degree of dispersion and the degree of mixing may be influenced by the average calcite agglomerate size, the average diameter of the air hole, and the aspect ratio upon stretching and mixing cycles. Those factors would be formed by the difference in chemical characteristics upon various microstructures of polyethylene and its molecular weight and molecular weight distribution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 311–321, 2003     

Manipulating the microstructure and rheology in polymer‐organoclay composites

A series of nanocomposites prepared by melt‐blending of cloisite‐based organoclays with poly(ethylene‐vinylacetate) (EVA) and neutralized poly (ethylene‐methacrylic acid) (EMA) copolymers were investigated via DSC, small‐angle X‐ray scattering (SAXS), and rheological techniques. SAXS results indicated partial clay exfoliation in all samples. In both EMA and EVA systems, the nominal melting temperature T_m and bulk crystallinity are not significantly affected by the presence of organoclays, suggesting that clay particles are predominantly confined in the amorphous phase. In rheological measurements (above T_m), the EVA‐clay system demonstrated a solid‐like rheological behavior under the small‐strain oscillatory shear, yet it was able to yield and flow under a steady shear, which is the characteristic of physical crosslinking. In contrast, the EMA‐clay system exhibited a melt‐like rheological behavior, where the influence of organoclay on the thermorheological behavior of the EMA composite was quite minimal. We propose that the carbonyl groups of vinylacetate in EVA interact with the clay surface, resulting in a strong physically crosslinking like interaction in the melt. On the other hand, the interaction between EMA and clay is weak because of repulsion between carboxyl anions and negatively charged clay surface.     

Preparation and characterization of a proton‐exchange membrane by the radiation grafting of styrene onto polytetrafluoroethylene films

Radiation‐induced simultaneous grafting of styrene onto polytetrafluoroethylene (PTFE) films and the subsequent sulfonation in the chlorosulfonic acid/dichloroethane were investigated. The effects of the main radiation grafting conditions, such as the type of solvents, irradiation dose, dose rate, the styrene concentrations, etc., on the degree of grafting (DOG) were studied. To elucidate the influence of both the grafting and sulfonation conditions on the properties of the PTFE‐g‐polystyrene‐sulfonic acid (PSSA) membranes, the sulfonation conditions, including the sulfonation temperature and the concentration of the ClSO₃H with respect to the DOG, were systematically evaluated. The grafted and sulfonated membranes were characterized by FTIR–ATR spectra, ion‐exchange capacity (IEC), water uptake, thickness measurement, etc. The as‐prepared PTFE‐g‐PSSA membranes in this work showed a good combination of a high IEC (0.85–2.75 meq g^?1), acceptable water uptake (8.86–56.9 wt %), low thickness, and volume expansion and/or contraction. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1415–1428, 2006     

Synthesis and characterization of in situ polymerized segmented thermoplastic elastomeric polyurethane/layered silicate clay nanocomposites

Nanocomposites based on thermoplastic elastomeric polyurethane (TPU) and layered silicate clay were prepared by in situ synthesis. The properties of nanocomposites of TPU with unmodified clay were compared with that of organically modified clay. The nanocomposites of the TPU and organomodified clay showed better dispersion and exhibited superior properties. Exfoliation of the clay layers was observed at low organoclay contents, whereas an intercalated morphology was observed at higher clay contents. As one of major purposes of this study, the effect of the silicate layers in the nanocomposites on the order–disorder transition temperature (T_ODT) of the TPU was evaluated from the intensity change of the hydrogen‐bonded and free carbonyl stretching peaks and from the peak position change of the N? H bending peak. The presence of the organoclay increased T_ODT by approximately 10°C, which indicated improved stability in the phase‐separated domain structure. The layered silicate clay caused a tremendous improvement in the stiffness of the TPU; meanwhile, a reduction in the ultimate elongation was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3048–3055, 2006     

PSA performances and viscoelastic properties of SIS‐based PSA blends with H‐DCPD tackifiers

Hotmelt pressure sensitive adhesives (PSAs) usually contain styrenic block copolymers like styrene–isoprene–styrene (SIS), SBS, SEBS, tackifier, oil, and additives. These block copolymers individually reveal no tack. Therefore, a tackifier is a low molecular weight material with high glass transition temperature (T_g), and imparts the tacky property to PSA. The SIS block copolymer with different diblocks was blended with hydrogenated dicyclopentadiene (H‐DCPD tackifier), which has three kinds of T_g. PSA performance was evaluated by probe tack, peel strength, and shear adhesion failure temperature. PSA is a viscoelastic material, so that its performance is significantly related to the viscoelastic properties of PSAs. We tested the viscoelastic properties by dynamic mechanical analysis and the thermal properties by differential scanning calorimeter to investigate the relation between viscoelastic properties and PSA performance. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 2839–2846, 2006     

Experimental analysis of bubble mode in a plate-type absorber

An experimental analysis of ammonia-water absorption was performed in a plate-type absorber. The flow of water and ammonia gas was performed in the bubble mode. The experiments were made to examine the effects of solution flow rate and gas flow rate on the performance of the absorber. It was found that the increase of solution flow rate rarely affected the mass transfer, but improved the heat transfer. As the gas flow rate increased, slugging occurred in the bubble mode and influenced the thermal boundary layer. Finally, the results were converted into dimensionless numbers to elucidate physical phenomena and plotted as Sherwood number versus Reynolds number for mass transfer performance and Nusselt number versus Reynolds number for heat transfer performance.