Thermochemische Kennwerte für die Reaktion,Mo + O2 ⇌ MoO2 sowie in Eisenschmelzen

Zusammenstellung von Schrifttumsangaben für die Änderung der freien Standardenthalpien der Reaktionen , Mo + O₂ ? MoO₂ und in Eisenschmelzen. Neubestimmung der Temperaturabhängigkeiten der Größen ΔG^oCr₂O₃, ΔG^oMoO₂ und ΔG^o_O im Eisen bei Temperaturen zwischen 1460 bzw. 1530 und 1725 °C. Nachweis der Anwendbarkeit der neu ermittelten thermodynamischen Funktionen durch EMK-Parallelmessungen an ThO₂ (Y₂O₃)- und ZrO₂ (MgO)-Festelektrolytzellen mit Cr-Cr₂O₃- und Mo-MoO₂-Referenzelektroden in Reineisenschmelzen bei 1600 °C. Ermittlung des Parameters p_e′ der Elektronenteilleitfähigkeit für einen teilstabilisierten ZrO₂-Festelektrolyten mit einem Stoffmengengehalt von 5% MgO.     

Micromechanics of solvent crazes in polystyrene

Double exposure holographic interferometry (DEHI) is used to determine the strain energy release rate, craze opening displacement profile, and craze stress profile ofn-heptane and methanol crazes growing from cracks in polystyrene.n-heptane crazes have strain energy release rates (SERRs) close to those of cracks and their stress profile is almost crack-like in that the tensile stress across the craze falls almost to zero. On the other hand, the SERRs of methanol crazes are only 30 to 55% the SERR of a crack depending on stress intensity factorK _I of the precrack from which they are grown. The stress profile of the methanol craze shows it to be strongly load-bearing away from the craze tip, apparently as a result of the strain hardening of the craze fibrils. The stress concentration in front of the methanol craze tip is only 40% of that in front of then-heptane craze tip. The opening displacements of the methanol craze are almost as large as those of a crack very near its tip but are much less than those of a crack at large distances behind the tip. The Dugdale model of a strip yielding zone provides a poor representation of the craze opening displacements of the growing methanol craze. Dry (static) methanol crazes have larger opening displacements in response to an incremental tensile strain at moderate prestrains than at either low or high prestrains, suggesting that the craze fibrils undergo a yielding/strain-hardening process as the strain is increased similar to that observed in polycarbonate crazes by Kopp and Kambour. Dryn-heptane crazes do not show this response but rather open linearly with increasing prestrain. The opening displacement for long (dry)n-heptane crazes is almost crack-like whereas the largest opening of a dry methanol craze is only 20% of that of a crack. Dry methanol crazes break at aK _IC that is 40% of theK _IC of precracked but uncrazed specimens. The strongest (shortest) dryn-heptane crazes fail at only 7% ofK _IC of uncrazed specimens and theK _IC of the dryn-heptane crazes decreases markedly with increasing craze length.     

A Study on the Buckling Behaviour of Strips and Plates with Residual Stresses

During and after rolling or flattening of metal strips and plates the permissible deviations from flatness are described by the permissible absolute wave height and the flatness index. Both values can be determined on a measuring table while the material is not subjected to global tension. Because this procedure is expensive, time‐consuming and allows measurement only at discrete positions along the strip length, on‐line flatness measuring systems are used which can detect the distribution of longitudinal tensile stresses distributed across the strip width allowing for the calculation of the flatness index. This value does not always agree with the value obtained directly by measuring on the table even when the measurement of the longitudinal tensile stress distribution operates perfectly. It can be shown that the measurement of the tensile stress distribution does not give a direct indication on the wave height in the tension‐free state determined on the measuring table. To explain the relationship between tensile stress distribution in the strip and the flatness measurement on the measuring table, the buckling behavior is analysed both with and without dead load for simple symmetrical residual stress distributions resulting, e.g., from the rolling process. Based on the knowledge of the distribution of the longitudinal residual stresses across the strip width, the flatness index and the wave height can be determined by using a specialized finite element model. If the direct measurement is performed under action of dead load, large differences between the directly and indirectly obtained flatness index are observed. Below a certain limit of the intensity of the residual stress distribution the strips and plates lie flat on the measuring table. Above this limit the strip lying on the table exhibits post‐bucking deformations. In the latter case, the wave height increases with strip thickness and intensity of residual stresses.     

Simulation of thermally induced package effects with regard to piezoresistive pressure sensors

Microsystems are on their way out of laboratories into production. One of these microsystems, a piezoresistive pressure sensor developed by Robert Bosch GmbH, is examined within this paper. Obviously, one can detect undesirable temperature effects resulting from the sensor package, which influence the electrical characteristics of the sensor. By means of finite-element modelling (FEM), a simulation of the temperature effects can be managed. It is also possible to search for alternative designs of the sensor package.     

A Probabilistic Approach to Concurrent Mapping and Localization for Mobile Robots

This paper addresses the problem of building large-scale geometric maps of indoor environments with mobile robots. It poses the map building problem as a constrained, probabilistic maximum-likelihood estimation problem. It then devises a practical algorithm for generating the most likely map from data, along with the most likely path taken by the robot. Experimental results in cyclic environments of size up to 80 by 25 meter illustrate the appropriateness of the approach.     

Polarization Phase-Based Method For Material Classification In Computer Vision

A robust and accurate polarization phase-based technique for material classification is presented. The novelty of this technique is three-fold in (i) its theoretical development, (ii) application, and, (iii) experimental implementation. The concept of phase of polarization of a light wave is introduced to computer vision for discrimination between materials according to their intrinsic electrical conductivity, such as distinguishing conducting metals, and poorly conducting dielectrics. Previous work has used intensity, color and polarization component ratios. This new method is based on the physical principle that metals retard orthogonal components of light upon reflection while dielectrics do not. This method has significant complementary advantages with respect to existing techniques, is computationally efficient, and can be easily implemented with existing imaging technology. Experiments for real circuit board inspection, nonconductive and conductive glass, and, outdoor object recognition have been performed to demonstrate its accuracy and potential capabilities.     

Die Geschichte der Vakuumkühlung. The History of Vacuum Refrigeration

The use of the high evaporation enthalpy of water is one of the oldest technologies of refrigeration for food preservation used by the mankind. One could nearly celebrate the true 5000^th anniversary of this technology. Nowadays we call the refrigeration by evaporation from wet surfaces “adiabatic refrigeration”, it regulates, for instance, our body heat by evaporating sweat. After the introduction of some vacuum pumps into the experimental scientific works, 250 years ago, namely in Great Britan, the modern form of “artificial” refrigeration began its career, the evaporation of liquids under the absence of permanent gasses in vacuum. The vacuum refrigeration has been nearly abruptly stopped by the development of compression refrigeration processes, about 150 years ago. Only after world war 2, a reintroduction of vacuum refrigeration began again. Now, at the beginning of the 3. milennium, there are good chances for recovering terrain.     

Biocompatibility study of three distinct carbon pastes for application as electrode material in neural stimulations and recordings

Neural interfaces hold great promise for research and treatment of a wide variety of neurological diseases. Medical electrodes are designed to interface with the nervous system and provide control signals for neural prostheses. We fabricated previously a hook-up neural electrode. Here we investigate the in vitro cytotoxicity of three commercial carbon pastes used for printing the conductor tracks of this electrode. At first, the carbon pastes were characterized with respect to their microstructure and chemical composition. SEM images showed a grainy texture that is associated to the carbon/graphite microparticles dispersed by the polymeric binder. All the three pastes contained in major proportions carbon and in different proportions other elements. The surface roughness analysis evidenced differences in the smoothness of the carbon paste surfaces. Sterilization procedures did not alter the microstructure or surface morphology of the pastes. Finally, cell viability based on -(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) test and fluorescence staining experiments proved non-cytotoxicity and suitability of the studied carbon pastes as electrode material for measuring neural activity during surgeries (up to a certain time period).