On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

基于多线程技术的监控系统的设计

详细介绍在32位操作系统Windows95／98下，用C Builder3．0开发基于多线程技术的监控系统的有关方法。     

全球3G市场管制政策分析

主要对各国3G许可证与使用技术标准的抽绑政策．各国对2G／3G网络漫游的管制规定。以及3G网络之间共享的种类及实施方式等方面做了详尽的讲解，并进行比较和分析。     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

丁苯干燥箱热风循环流程的改造

齐鲁股份有限公司橡胶厂针对丁苯橡胶装置干燥箱的设计及运行缺陷,借鉴吸收国内外先进干燥箱的生产技术与经验,组织技术攻关,对干燥箱热风循环工艺流程进行改造,实现了节能降耗以及废气污染物排放的减少,提高了干燥箱热能利用效率与生产能力。     

油气吸收回收系统的研究及工业应用——(Ⅰ)中型试验及结果分析

在蒸发油气吸收回收技术小试研究的基础上，开发出常温常压吸收法油气回收中试装置，并利用已开发的吸收剂AbsFOV-97进行了中试试验。结果表明，当系统进料气、吸收剂AbsFOV-97、汽油的体积流量比为10．0：1．0：0．5、真空泵解吸压力小于13．3kPa时，系统回收率高达97％以上，高于设计指标，且回收汽油的质量满足使用要求。统计数据表明，油气回收系统进料气、尾气中平均油气摩尔质量分别为65．51、48．97g／mol，该值可为油品蒸发损耗及其控制技术的评价提供参考。     

对重油催化裂化反应历程的若干再认识——"新型多区协控重油催化裂化技术MZCC"的提出

基于对重油催化裂化反应历程的若干再认识,以高油剂混合能量短接触时间催化裂化为工艺基础,提出了进料强返混、反应平流推进、产物超快分离及化学汽提的分区协同控制新理念和实现分区协同控制反应的新技术.并且为实现高油剂混合能量短接触时间催化裂化提出了新型反应器结构;同时对汽提段的功能进行了拓展与强化,提出了"化学汽提器"的概念.分区协同控制反应的技术以进一步提高轻质油收率和实现装置长周期运行为目标,有着重要的理论和实际意义.     

容灾系统中存储方案选择的研究

论文首先阐述了在容灾系统中存储方案的重要性,讨论了存储方案需要考虑的衡量指标,然后介绍了主要的存储方式,根据衡量指标划分了存储方式的特性范围,最后着重研究了容灾系统中存储方案的选择流程,并使用一个实例说明容灾系统中存储方案的选择流程。     

基于单片机加压控制的PCD复合片真空扩散焊接

文章针对普通钎焊的聚晶金刚石钻头剪切强度不高，提出了采用单片机加压控制的PCD复合片真空扩散焊接的设计思想，在对原真空扩散焊机液压改造的基础上给出如何由单片机控制加压的电路和程序流程设计。实际应用表明，该技术经济实用，有较好的经济效益。     

双层有机电致发光器件有机层厚度优化的数值研究

在陷阱电荷限制电流传导理论的基础上,提出了双层有机电致发光器件的数值模型,研究了结构为"阳极/空穴输运层(HTL)/发光层(EML)/阴极"的器件中电流密度和量子效率随有机层的特征陷阱能量、陷阱密度和载流子迁移率的依赖关系. 研究发现,对于给定的HTL和EML的特征陷阱能量、陷阱密度和载流子迁移率,存在一个最优的HTL和EML之间的厚度比率,在此最优厚度比下,器件的电流密度和量子效率达到最大.通过有机层厚度的优化,器件的电流密度和量子效率可提高多达两个数量级.另外,还研究了最优厚度比随有机层特征陷阱能量、总陷阱密度和载流子迁移率之间的定量关系.