Heat transfer to laminar flow with temperature — dependent heat generation

Two problems were solved theoretically on the heat transfer to circular tube flow with internal heat source. The one problem is to maintain the mixed-mean temperature of fluid at the inlet temperature. The other is a conjugated problem with a uniformly specified temperature at the outside surface of the wall, accounting for the wall conduction. From the numerical example for the former, it is shown that the mixed-mean temperature can be controlled within 15% error under the estimated condition. From the numerical results for the latter, it is concluded that the influence of wall conduction is more serious than the case without heat generation.     

One-step formation of ethyl methyl ketone from 1-butene and water on ultrastable Y-type zeolite catalyst

Proton exchanged ultrastable Y-type zeolite with silica/alumina = 40 showed a pronounced catalytic activity for the formation of ethyl methyl ketone directly from 1-butene and water. The formation rate of ethyl methyl ketone was much higher than those on MoO₃-based catalysts in the oxidation of 1-butene by oxygen. It was suggested that the basic site necessary for the formation of ethyl ketone directly from 1-butene and water would be the pentacoordinated Al.     

Electron-beam irradiation-induced grafting of acrylonitrile onto polyethylene

Low- and high-density polyethylene (PE) films were grafted with acrylonitrile (AN) by electron beam prior to irradiation. The distribution of graft chains over the cross section of the sample film was analyzed in terms of the distribution of nitrogen atoms contained in the AN by means of an electron probe microanalyzer (EPMA), and graft sites were studied in relation to the effect of grafting temperature on the percent graft and the oxygen permeability of the sample films. It was found that diffusion of AN into the film was the rate-limiting step in the grafting process, thus restricting the grafting to the surface of the film in the initial grafting stages. However, the grafting shifted to the center of film as the graft process proceeded, until a uniform distribution of graft chains was observed across the entire film thickness. High-density polyethylene (HDPE) was found to display a higher percent graft than did low-density polyethylene (LDPE), and percent graft tended to increase with increasing grafting temperature. On the other hand, film oxygen permeability decreased with increasing percent graft, but this decreasing trend decreased with increasing percent graft. These findings suggest that the grafting is initiated by radicals trapped in the amorphous phase near the crystalline regions and at the surface of crystallites and that graft chains grow toward the amorphous regions. As for the radicals contributing to graft polymerization, it appears that AN permeates deeper near the crystalline surface and that graft chains grow from these sites.     

Lab-scale feasibility study on new elastomer comprising chloroprene and acrylonitrile for oil and gas applications

The limited options of suitable elastomers with adequate cost-performance balance drive the necessity to introduce new materials in the oil & gas (O&G) application space. The relevance of a recently developed copolymer of chloroprene and acrylonitrile (referred to as acrylonitrile–chloroprene rubber or NCR) to O&G applications is described in this technical contribution. The new elastomer demonstrates adequate physical properties and reasonably good high and low-temperature capabilities. It offers good resistance to several aqueous and non-aqueous fluids with low volume swelling and retains its physical properties to reasonable extents while exposed to hot test oils. Acrylonitrile–chloroprene rubber has been found to sustain “sour gas” exposure. Good abrasion resistance, high tear strength, and remarkably high flex-fatigue resistance coupled with low heat build-up reflect its durability under dynamic conditions. In addition, acrylonitrile–chloroprene rubber can very well withstand the rapid gas decompression test at 25°C. This unique combination of attributes may allow acrylonitrile–chloroprene rubber to be considered as a candidate material for high-performance O&G applications.     

Adaptive interpolation scheme for NURBS curves with the integration of machining dynamics

This paper develops a comprehensive interpolation scheme for non-uniform rational B-spline (NURBS) curves, which does not only simultaneously meet the requirements of both constant feedrate and chord accuracy, but also real-time integrates machining dynamics in the interpolation stage. Although the existing work in this regard has realized the importance to simultaneously consider chord error and machining dynamics, none has really incorporated these in one complete interpolation scheme. In this paper, machining dynamics is considered for three aspects: sharp corners or feedrate sensitive corners on the curves, components with high frequencies or frequencies matching machine natural ones and high jerks. A look-ahead module was developed for detecting and adaptively adjusting the feedrate at the sharp corners. By Fast Fourier Transform (FFT) analysis with a moving window in the interpolation stage identified were some special frequency components such as those containing high frequencies or with frequencies matching machine natural ones. Then, the notch filtering or time spacing method was used to eliminate these components. To more completely reduce feedrate and acceleration fluctuations, the jerk-limited algorithm was also developed. Finally, the interpolated feedrate was further smoothened with B-spline fitting method and the NURBS curves were re-interpolated with the smoothened feedrate. During the interpolation, the chord error was repeatedly checked and confined in the prescribed tolerance. Two NURBS curves were used as examples to test the feasibility of the developed interpolation scheme.     

Data Center as a Key Player of a District Electric Power and Heat Network System： A Comparison in Urban and Suburb Regions

A DC （data center） demands air-conditioning power as large as the 1/3-1/2 of total electricity consumption. Thus, energy saving of cooling power of DC yields considerable effect on both economic and environmental views. PV （Photovoltaic） and absorption refrigerator with CGS （cogeneration systems） or gas boiler are possible power saving options. The waste warm air from DC would be utilized for greenhouse heating when DC and greenhouse locate near in the suburbs. In this study, the authors develop an energy network model to assess the potential contribution of DC as a major electric power and chilled air consumer as well as the warm air supplier in a district to the energy efficiency improvement. The evaporation heat of LNG （liquefied natural gas） utilization is also considered as well as PV, CGS. This model is applied to the cases of the urban area in Tokyo which involves athletic center, shops and hospital and the suburbs including greenhouse and then compared.     

Autonomic load balancing of flow monitors

In monitoring flows at routers for flow analysis or deep packet inspection, the monitor calculates hash values from the flow ID of each packet arriving at the input port of the router. Therefore, the monitors must update the flow table at the transmission line rate, so high-speed and high-cost memory, such as SRAM, is used for the flow table. This requires the monitors to limit the monitoring target to just some of the flows. However, if the monitors randomly select the monitoring targets, multiple routers on the route will sometimes monitor the same flow, or no monitors will monitor a flow. To maximize the number of monitored flows in the entire network, the monitors must select the monitoring targets while maintaining a balanced load among them. We propose an autonomous load-balancing method where monitors exchange information on monitor load only with adjacent monitors. Numerical evaluations using the actual traffic matrix of Internet2 show that the proposed method improves the total monitored flow count by about 50% compared with that of independent sampling. Moreover, we evaluate the load-balancing effect on 36 backbone networks of commercial ISPs.     

Transflective IPS‐LCD with improved reflective contrast ratio

Abstract— In order to improve the reflective contrast ratio of transflective IPS‐LCDs, a novel pixel design for a normally white reflective IPS has been proposed. In this design, the large‐inter‐electrode‐spacing layout using a novel driving method and a double‐layered electrode have effectively reduced the light leakage. By applying these two technologies, a transflective IPS‐LCD has been successfully demonstrated with a high contrast ratio (15:1) in the reflective mode and a wide‐viewing‐angle characteristic in the transmissive mode.     

Ergonomics solution for crossing collisions based on field assessment of visual environment at urban intersections in Japan

This paper aims to assess quantitatively the actual visual environment of uncontrolled urban downtown intersections in Japan in relation to frequently occurring crossing collisions and to discuss the safety countermeasures for them. In Field Study 1 dealing with direct visibility, our ultra-wide-angle photograph analysis revealed that most of the right/left-ward visible range at 11 intersections were insufficient to check safety, and the quality of direct visibility was closely associated with causing crossing collisions. The countermeasures to reduce a blind area were determined to be a top priority. In Field Study 2 dealing with indirect visibility, more than half of the 25 traffic convex mirrors had marked shortcomings for preventive safety, and ergonomics guidelines ensuring indirect visibility were proposed for installing traffic convex mirrors. Low-cost/low-technology-oriented countermeasures are highly recommended to obtain clear/sufficient images of crucial information satisfying drivers' requirements on traffic convex mirrors in accordance with those ergonomics guidelines was highly recommended. Crossing collisions could be prevented by improvement of poor direct and indirect visibility.     

Studies of 2D Cryocrystals by STM Techniques

Scanning tunneling microscopy (STM) studies of two-dimensional (2D) cryocrystals ⁴ He, Kr, Xe) physisorbed on graphite surfaces are presented. Individual helium atoms, usually thought to be invisible with STM, were recently observed on graphite surfaces at a density corresponding to the commensurate solid. Here we show that a local elastic deformation seems to be the principal mechanism responsible to render the atoms visible. Recent tight-binding calculations of the local density of states (LDOS) of graphite which predict the appearance of an energy gap support this picture. I-z curve measurements for the case of ⁴ He show a sharp drop (increase) of the tunneling current I at a certain tip-surface distance z during retraction (approach) of the tip. This drop (increase) may be associated with the tunneling of a single He adatom, opening new possibilities to study the quantum tunneling of atoms via STM.