Tribological behavior of composites fabricated by reactive SPS sintering in Ti-Si-C system

In this study, wear and friction behavior of two based-composites from the Ti-Si-C system, (40 wt% TiC; 28 wt% Ti₅Si₃; 17 wt% Ti₃SiC₂) and (18 wt% TiC; 26 wt% Ti₅Si₃; 41 wt% Ti₃SiC₂) reinforced by 15 wt% of large size SiC (100-150 µm) particles were investigated. The four-phase composites exhibited approximatively the same friction coefficient (µ ~ 0.9) under high loads (10 N and 7 N). The composite with high Ti₃SiC₂ showed higher wear rate values by one order of magnitude. However, under 1 N, the composite with high TiC content showed a higher running-in period and a lower steady state µ value (0.37 after 1000 m sliding distance). Scanning electron microscopy, Energy Dispersive X-Ray and Raman spectroscopy analysis of the worn surfaces of the two composites revealed that oxidation was the dominant wear mechanism. The oxidation process and the removal kinetics of the oxides during sliding controlled the tribological behavior of the composites. The influence of processing variables on microstructures development and wear mechanisms of the composites is discussed.     

Disrupting the methionine biosynthetic pathway in Candida guilliermondii: characterization of the MET2 gene as counter‐selectable marker

Candida guilliermondii (teleomorph Meyerozyma guilliermondii) is an ascomycetous species belonging to the fungal CTG clade. This yeast remains actively studied as a result of its moderate clinical importance and most of all for its potential uses in biotechnology. The aim of the present study was to establish a convenient transformation system for C. guilliermondii by developing both a methionine auxotroph recipient strain and a functional MET gene as selection marker. We first disrupted the MET2 and MET15 genes encoding homoserine‐O‐acetyltransferase and O‐acetylserine O‐acetylhomoserine sulphydrylase, respectively. The met2 mutant was shown to be a methionine auxotroph in contrast to met15 which was not. Interestingly, met2 and met15 mutants formed brown colonies when cultured on lead‐containing medium, contrary to the wild‐type strain, which develop as white colonies on this medium. The MET2 wild‐type allele was successfully used to transfer a yellow fluorescent protein (YFP) gene‐expressing vector into the met2 recipient strain. In addition, we showed that the loss of the MET2‐containing YFP‐expressing plasmid can be easily observed on lead‐containing medium. The MET2 wild‐type allele, flanked by two short repeated sequences, was then used to disrupt the LYS2 gene (encoding the α‐aminoadipate reductase) in the C. guilliermondii met2 recipient strain. The resulting lys2 mutants displayed, as expected, auxotrophy for lysine. Unfortunately, all our attempts to pop‐out the MET2 marker (following the recombination of the bordering repeat sequences) from a target lys2 locus were unsuccessful using white/brown colony colour screening. Nevertheless, this MET2 transformation/disruption system represents a new versatile genetic tool for C. guilliermondii. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis of fatty hydroxamic acids catalyzed by the lipase ofMucor miehei

Biotechnological synthesis of a new class of amphiphilic molecules—fatty hydroxamic acids—was carried out using the lipase ofMucor miehei by reacting hydroxyl amine with the fatty acids in their free or methyl ester form. Concurrently with enzymatic synthesis, chemical synthesis of hydroxamic fatty acids has also been developed by adapting methods that already existed for water-soluble acids. Different parameters were studied to determine the optimum operating conditions: temperature, molar ratio of reagents, quantity of biocatalyst and length of reaction. A general method, whatever the type of fatty acids used, is described.     

INFLUENCE OF MATERIAL REMOVAL ON THE DYNAMIC BEHAVIOR OF THIN-WALLED STRUCTURES IN PERIPHERAL MILLING

Machining is a material removal process that alters the dynamic properties during machining operations. The peripheral milling of a thin-walled structure generates vibration of the workpiece and this influences the quality of the machined surface. A reduction of tool life and spindle life can also be experienced when machining is subjected to vibration. In this paper, the linearized stability lobes theory allows us to determine critical and optimal cutting conditions for which vibration is not apparent in the milling of thin-walled workpieces. The evolution of the mechanical parameters of the cutting tool, machine tool and workpiece during the milling operation are not taken into account. The critical and optimal cutting conditions depend on dynamic properties of the workpiece. It is illustrated how the stability lobes theory is used to evaluate the variation of the dynamic properties of the thin-walled workpiece. We use both modal measurement and finite element method to establish a 3D representation of stability lobes. The 3D representation allows us to identify spindle speed values at which the variation of spindle speed is initiated to improve the surface finish of the workpiece.     

Neutronic characterization of the MEGAPIE target

The MEGAPIE project aimed to design, build and operate a liquid metal spallation neutron target of about 1 MW beam power in the SINQ facility at the Paul Scherrer Institut (Villigen, Switzerland). This project is an important step in the roadmap towards the demonstration of the accelerator driven system (ADS) concept and high power liquid metal targets in general. Following the design phase, an experimental program was defined to provide a complete characterization of the facility by performing a “mapping” of the neutron flux at different points, from the center of the target to the beam lines. The neutronic performance of the target was studied using different experimental techniques with the goals of validating the Monte Carlo codes used in the design of the target; additionally, the performance was compared with the solid lead targets used before and after the MEGAPIE experiment.     

Market Coordination Under Non-Equilibrium Dynamics

Networks and Spatial Economics - In order to study the market coordination under non-equilibrium dynamics, such as the one outlined in catallactics, we consider a multi-agent system with fixed...     

Co/SiO2 catalysts prepared from Co2(CO)8 for CO hydrogenation into alcohols and hydrocarbons: characterization by magnetic methods and temperature-programmed hydrogenation

The hydrogenation of carbon monoxide over Co/SiO₂ catalysts obtained by reduction of precursors prepared by the reaction of dicobaltoctacarbonyl with silica gives rise to a mixture of alcohols and hydrocarbons. The chain growth probability for hydrocarbon synthesis is similar to that observed over conventional catalysts prepared by the ammonia method (=0.74) with a comparable metal dispersion (metal particle size 4 nm). Alcohol formation yields a smaller chain growth probability (=0.42). Magnetic measurements have shown that in the latter catalyst, small cobalt clusters (1 nm) are likely to be present together with the cobalt particles (4 nm), this observation reconciles apparently conflicting results from the literature. It has been speculated that alcohol formation might be related to the presence of these clusters according to a concerted mechanism. Furthermore, the observation of large amounts of acetates by temperature-programmed hydrogenation, not detected in hydrocarbon selective catalysts, suggests that they may play a role in ethanol synthesis.     

Surface roughness variation of thin wall milling, related to modal interactions

High-speed milling operations of thin walls are often limited by the so-called regenerative effect that causes poor surface finish. The aim of this paper is to examine the link between chatter instability and surface roughness evolution for thin wall milling. Firstly, the linear stability lobes theory for the thin wall milling optimisation was used. Then, in order to consider the modal interactions, an explicit numerical model was developed. The resulting nonlinear system of delay differential equations is solved by numerical integration. The model takes into account the coupling mode, the modal shape, the fact that the tool may leave the cut and the ploughing effect. Dedicated experiments are carried out in order to confirm this modelling. This paper presents surface roughness and chatter frequency measurements. The stability lobes are validated by thin wall milling. Finally, the modal behaviour and the mode coupling give a new interpretation of the complex surface finish deterioration often observed during thin wall milling.     

Rehydration process of milk protein concentrate powder monitored by static light scattering

Static light scattering (SLS) was applied to monitor the rehydration process of milk protein concentrate (MPC) powder. The size distribution and volume concentration of the suspended powder particles were measured to quantify the dissolution kinetics of MPC powder. The results obtained showed that the low solubility index reported for MPC85 (85% protein) powder at room temperature was the consequence of slow dissolution kinetics rather than the presence of a large amount of insoluble material in the rehydrated powder. The rehydration process of MPC85 powder occurs in two overlapping steps: the disruption of agglomerated particles into primary powder particles and, simultaneously, the release of material from the powder particles into the surrounding aqueous phase. The latter process appeared to be the rate-limiting step of dissolution of MPC85 and was accelerated by an increase of the solvent temperature.